Discussion
I was getting pulsing brakes while slowing down to a stop on my blade. Essentially when you braked from say 60 the brakes would vibrate a bit (you could feel it most with the clutch in) and then the bike would slow and the frequency of the pulsing would decrease with wheel speed until at about 10mph there was a definite pulse to them.
Putting this down to the discs (the bike has done 37500 miles) I replaced with new. The problem persists. The mating faces on the wheel were cleaned, the disc mounting faces were cleaned, brand new honda OE pads were used and the fluid changed a fortnight ago.
Is there anything other than discs that can cause road wheel speed frequency pulsing on the front brakes?
Thanks,
Mark
Putting this down to the discs (the bike has done 37500 miles) I replaced with new. The problem persists. The mating faces on the wheel were cleaned, the disc mounting faces were cleaned, brand new honda OE pads were used and the fluid changed a fortnight ago.
Is there anything other than discs that can cause road wheel speed frequency pulsing on the front brakes?
Thanks,
Mark
dern said:
I was getting pulsing brakes while slowing down to a stop on my blade. Essentially when you braked from say 60 the brakes would vibrate a bit (you could feel it most with the clutch in) and then the bike would slow and the frequency of the pulsing would decrease with wheel speed until at about 10mph there was a definite pulse to them.
Putting this down to the discs (the bike has done 37500 miles) I replaced with new. The problem persists. The mating faces on the wheel were cleaned, the disc mounting faces were cleaned, brand new honda OE pads were used and the fluid changed a fortnight ago.
Is there anything other than discs that can cause road wheel speed frequency pulsing on the front brakes?
Thanks,
Mark
Check for the wheel being bent a bit, tyre misalignment or distorted etc. It might feel like it is your brakes, but could be the wheel itself.Putting this down to the discs (the bike has done 37500 miles) I replaced with new. The problem persists. The mating faces on the wheel were cleaned, the disc mounting faces were cleaned, brand new honda OE pads were used and the fluid changed a fortnight ago.
Is there anything other than discs that can cause road wheel speed frequency pulsing on the front brakes?
Thanks,
Mark
King Herald said:
Check for the wheel being bent a bit, tyre misalignment or distorted etc. It might feel like it is your brakes, but could be the wheel itself.
If I slow to a stop you can visibly see the screen go down as the forks compress and then lift as the braking force increases and decreases as it pulses. I can see how a distorted wheel cause cause the disc to be misshaped but the discs do sit flat on the wheel mount points prior to bolting on. If the wheel was buckled or the tyre distorted I think it would vibrate for sure but I would get that compression/decompression of the forks.Cheers,
Mark
dern said:
King Herald said:
Check for the wheel being bent a bit, tyre misalignment or distorted etc. It might feel like it is your brakes, but could be the wheel itself.
If I slow to a stop you can visibly see the screen go down as the forks compress and then lift as the braking force increases and decreases as it pulses. I can see how a distorted wheel cause cause the disc to be misshaped but the discs do sit flat on the wheel mount points prior to bolting on. If the wheel was buckled or the tyre distorted I think it would vibrate for sure but I would get that compression/decompression of the forks.Cheers,
Mark
If you have access to a micrometer measure the thickness at a half dozen places around each disc, see if there is more than about 0.05mm variation. That will be enough to makes your brakes feel like they do.
Busamav said:
I would lift the front end and spin the wheel whilst holding a screwdriver or similar at a fixed point to check for any deviation n the disc .
There is some slight deviation on one disc but it's less than .1mmm according to my feeler gauge and .3mm is within spec. Rolling the wheel round does make it feel really slightly grabby at a certain point but only very slightly.Busamav said:
Have you cleaned the calipers up , inc the pins holding the pads .
Yep, did the lot a couple of weeks ago.King Herald said:
Does sound like a brake grabbing then. Do as Busamav says, prop the front up solidly and get someone to spin the wheel while you carefully eyeball the discs for run out or distortion. Are these fully floating discs?
They are. There's nothing you can actually see and hardly anything you can measure.King Herald said:
If you have access to a micrometer measure the thickness at a half dozen places around each disc, see if there is more than about 0.05mm variation. That will be enough to makes your brakes feel like they do.
I'll try that (the battery is dead in it - that'll teach me for going all modern).Yoda954 said:
Was it you that had the fork re-call done recently? Just wondering if it's related to some odd way?....no idea at all of a cure, but just throwing a thought your way
Yes, that was me. I had new fork lowers, new oil, new seals etc. They feel ok to me. The wheel bearings feel fine too and I checked the steering head bearing feel and torque.At a loss and it's unrideable

King Herald said:
If you have access to a micrometer measure the thickness at a half dozen places around each disc, see if there is more than about 0.05mm variation. That will be enough to makes your brakes feel like they do.
Rigged up a battery to the micrometer and measured the discs. It seems like the intended thickness of the discs is supposed to be 4.50mm however on the right hand disc there's a high point about 6 inches long where the edge thickness at least rises to 4.59mm in places. This coincides with some relatively heavy pad deposits round the edge. The other disc isn't so bad but one place does rise in thickness to 4.55mm and that coincides with the other side unfortunately which can only (I imagine) exacerbate the problem.I took it for another test ride and using gradual braking (gentle one fingered) from 40mph on a flat bit of road with the clutch in doesn't produce any pulsing at the lever or excessive suspension travel but provides gentle braking but with all I can describe as an undulating grab/release/grab/release type braking pulsing action. Obviously I can make this a lot worse by using more brake but I think that the varying thickness of the right disc is probably the cause. I'll contact the supplier.
Thanks,
Mark
dern said:
It seems like the intended thickness of the discs is supposed to be 4.50mm however on the right hand disc there's a high point about 6 inches long where the edge thickness at least rises to 4.59mm in places. This coincides with some relatively heavy pad deposits round the edge. The other disc isn't so bad but one place does rise in thickness to 4.55mm and that coincides with the other side unfortunately which can only (I imagine) exacerbate the problem.
I took it for another test ride and using gradual braking (gentle one fingered) from 40mph on a flat bit of road with the clutch in doesn't produce any pulsing at the lever or excessive suspension travel but provides gentle braking but with all I can describe as an undulating grab/release/grab/release type braking pulsing action. Obviously I can make this a lot worse by using more brake but I think that the varying thickness of the right disc is probably the cause. I'll contact the supplier.
Thanks,
Mark
I used to skim bike discs for friends when I worked in a machine shop years ago. The only way to do it was to machine both sides in one hit, without taking it out of the lathe. Some were impossible to do like that, but no matter how accurately I trued it up when I turned it round to machine the other side, it was impossible to get it realigned parallel enough to give surge free braking. Two thousandths of an inch (or 0.05mm) was enough to have people complaining about the braking.I took it for another test ride and using gradual braking (gentle one fingered) from 40mph on a flat bit of road with the clutch in doesn't produce any pulsing at the lever or excessive suspension travel but provides gentle braking but with all I can describe as an undulating grab/release/grab/release type braking pulsing action. Obviously I can make this a lot worse by using more brake but I think that the varying thickness of the right disc is probably the cause. I'll contact the supplier.
Thanks,
Mark
King Herald said:
I used to skim bike discs for friends when I worked in a machine shop years ago. The only way to do it was to machine both sides in one hit, without taking it out of the lathe. Some were impossible to do like that, but no matter how accurately I trued it up when I turned it round to machine the other side, it was impossible to get it realigned parallel enough to give surge free braking. Two thousandths of an inch (or 0.05mm) was enough to have people complaining about the braking.
Ah. That'll probably be it then. Cheers,
Mark
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff




.