Front tyre wear
Discussion
Just curious, having ridden for a few years now, I am used to going through almost 2 rear tyres, to every front. Has always been the case on all bikes I have had (punctures excluded obviously).
However was looking at the Bandit tyres (BT0-20/21 - whatever the touring tyre is called), both were put on at the same time approx 3000 miles ago. The front probably has another 500 miles in, and the rear has much more. I would have expected (based on previous tyres and bikes) to have got around 3500/4000 on the rear, and double on the front.
This is used as a commuter, so although the chicken strips have gone (on back at least), most of the wear is down the middle of the tyres.
What would cause this?
However was looking at the Bandit tyres (BT0-20/21 - whatever the touring tyre is called), both were put on at the same time approx 3000 miles ago. The front probably has another 500 miles in, and the rear has much more. I would have expected (based on previous tyres and bikes) to have got around 3500/4000 on the rear, and double on the front.
This is used as a commuter, so although the chicken strips have gone (on back at least), most of the wear is down the middle of the tyres.
What would cause this?
Firstly - please note that my knowledge of motorbikes is very similar to Chilli's (no disrespect Chilli - but you know what I mean).
I love riding bikes, and I can check tyres, tyre pressure, and adjust the chain. Apart from this I cannot do anything, or really understand anything about bikes!
The suspension is as it is - I have not done any of this clicks up and down, rebound damper stuff that I don't understand, but read on here sometimes!
Sorry for being so non-descript - but I am a bit out of my depth here, just wanted to know why front is wearing so quickly!
I love riding bikes, and I can check tyres, tyre pressure, and adjust the chain. Apart from this I cannot do anything, or really understand anything about bikes!
StevRS said:
Is the front a softer compound? Is the front alignment or front suspension a bit off? Are you loading more weight forward on the bike?
Both are the same tyre - so I assume same compound. I did have a leak on the front fork seal that was only fixed recently - so there was probably suspension offness, during the life of this tyre. I only noticed by the liquid on the wheel, not by the feel of anything different on the bike.The suspension is as it is - I have not done any of this clicks up and down, rebound damper stuff that I don't understand, but read on here sometimes!
black-k1 said:
Are your front brakes binding slightly?
I don't understand this comment! It is the ABS version if that helps?Sorry for being so non-descript - but I am a bit out of my depth here, just wanted to know why front is wearing so quickly!
Fats25 said:
black-k1 said:
Are your front brakes binding slightly?
I don't understand this comment! It is the ABS version if that helps?Sorry for being so non-descript - but I am a bit out of my depth here, just wanted to know why front is wearing so quickly!
OK, a quick, non-technical explanation of what happens when you apply the brake while the bike is moving.
The brakes work by pressing the brake pads against the disk using the force you apply through the brake lever. The harder you pull the lever the harder the pads press against the disk effectively trying to stop the wheel rotating. Meanwhile, the momentum of the bike is still pushing the bike forward and thus trying to make the wheel spin. So we have brakes trying to stop the wheel spinning and forward momentum trying to make the wheel spin by pushing the wheel along the tarmac.
When the brake lever is released the pressure comes off the brake pads and they, in turn, should ‘let go’ of the brake disk. This means that the only thing that is happening to the wheel is that the forward momentum of the bike is making the wheel spin by it running along the tarmac.
So what is binding brakes and how will it cause the tyre to wear out quicker.
Now, if the brake pads don’t fully release the disk when the brake lever is released (because, for example, there is too much muck in the brake callipers) then there will still be braking force trying to stop the wheel turning. This means that more ‘effort’ has to be put through the tarmac (via the tyre) to ensure that the wheel keeps spinning. This ‘extra force’ will then cause the tyre to wear out sooner.
So how do I check?
The easiest way to test for brake binding is to lift the front wheel off the ground via a stand or something and spin the wheel by hand. It should spin reasonably freely and continue spinning for a couple of seconds afterwards. If there is resitance to the wheel being spun or the wheel stops almost instantly your hand comes off the tyre then you likely have a brake binding issue. This test needs to be carried out both when the brakes are cold, and when the brakes are warm (immediately after normal use) as there may be something that isn’t a problem when cold but the expansion due to the heat causes the brakes to bind.
I hope that helps.
Fats25 said:
black-k1 said:
Are your front brakes binding slightly?
I don't understand this comment! It is the ABS version if that helps?Sorry for being so non-descript - but I am a bit out of my depth here, just wanted to know why front is wearing so quickly!
Ah, beaten to it

Edited by dern on Friday 12th September 12:29
Dern & Black K1 - understood even by a retard like me.
Will try this when I get home tonight. To be fair last time it had a service they mentioned that the pads would need replacing at next service, so perhaps I have worn through quicker than expected. I have to admit I am pretty hard on the brakes, as I am a fat b
d and it takes a lot to stop me, and with ABS I can give it everything to stop on the bike without fear of locking them.
I will take a look when I get home, and see from there.
Thanks
Will try this when I get home tonight. To be fair last time it had a service they mentioned that the pads would need replacing at next service, so perhaps I have worn through quicker than expected. I have to admit I am pretty hard on the brakes, as I am a fat b
d and it takes a lot to stop me, and with ABS I can give it everything to stop on the bike without fear of locking them.I will take a look when I get home, and see from there.
Thanks
My FJR 1300, used for "enthusiastic" commuting, shows similar tendencies with the BT021's. Front is v.worn and tramlining a lot at 4500 miles, while rear would still do another 1000 or so. New rubber goes on next week - I've opted to stay with the 'stones as they grip well and were v.predictable until recently. The FJR is obviously heavier than your Bandit but it sounds a similar pattern. My dealer reports this tends to be the norm with the FJR's he sees although obviously depends how you ride it!
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff




