Discussion
Have a look here, a decent garage shouldn't charge more than £30-40 for fitting.
http://www.bandcexpress.co.uk/cgi-bin/bc_page.pl?c...
http://www.bandcexpress.co.uk/cgi-bin/bc_page.pl?c...
Agreed, wouldn't reccomend trying it yourself unless you can get your hands on a dremmel or similar to cut the heads off the old link, and a chain riveting tool to put it back togehter. A decent garage should charge you under an hours labour to do it. £100-£150 for the chain and sprockets, genuine Yam will be more expensive (£45 compared to £12 for my front sprocket) and no better.
RizzoTheRat said:
Agreed, wouldn't reccomend trying it yourself unless you can get your hands on a dremmel or similar to cut the heads off the old link
Or a hacksaw and just hack through the old chain 
RizzoTheRat said:
and a chain riveting tool to put it back togehter.
A must have for the job!Busamav said:
if you do go ahead and try it your self ( and i wouldnt recomend it either )
Do not remove the chain untill you have the engine sprocket loosened off
To do the job you will need:Do not remove the chain untill you have the engine sprocket loosened off
Paddock stand
Hex / Alen keys
Screw drivers + and - ones
1/2 Drive socket set (with large sockets)
Possibly a bigger socket for wheel nut
Breaker Bar
Chain busting tool of your choice
Riveting tool
Big Hammer
Loctite
Torque wench
If your answer to anything on the list is "what's that", then take it to a shop. Or if your name is Chilli...
smack said:
RizzoTheRat said:
and a chain riveting tool to put it back togehter.
A must have for the job!
t and an angle grinder will take your old chain off more efficiently and a ball pein hammer will mushroom the ends of the pins more convincingly. If you want one though you can fetch mine... it's covered in blood, an important (and weak) bit snapped off and embedded in the wall of my garage 
RizzoTheRat said:
Trouble I had doing one with a ball pien was stopping it moving, managed to wedge a sledge hammer against the back of the chain in the end but it was still a pain in the backside. Borrowed a Whale chain rivting tool off a mate for the last one and it worked really well.
I have a lump hammer with flat sides which I use as an anvil.Having just done a google that whale one looks pretty good. I bought the generic s
t motrax one to my cost.Edited by dern on Monday 15th September 15:39
I have the Whale tool, it has been a good to me so far, and nice and solid. Didn't really work for pin extraction, as all my bashing energy wasn't going into the pin with the chain flexing. I could have messed around with something hard/heaving behind the chain - but a hacksaw was the nearest thing to hand.
An angle grinder will be noisy, slightly dangerous, and give you cool sparks - so clearly this is the preferred method!
But I see we all recommend a very large hammer for the job
An angle grinder will be noisy, slightly dangerous, and give you cool sparks - so clearly this is the preferred method!

But I see we all recommend a very large hammer for the job

RizzoTheRat said:
smack said:
But I see we all recommend a very large hammer for the job 
A real mans toolkit consists of two tools; a hammer and a roll of gaffer tape. If it moves and it shouldn't, tape it; if it should and doesn't, hit it with the hammer! 

Chain and Sprockets are not worth skimping on.
Cheap ones wear out quickly in my experiance.
But a DID O ring chain and decent sprockets.
Do Yanaha do an OE replacement?
I know Honda do.
They realised how much they were missing out on and came up with some very realistic prices for genuine kit.
Cheap ones wear out quickly in my experiance.
But a DID O ring chain and decent sprockets.
Do Yanaha do an OE replacement?
I know Honda do.
They realised how much they were missing out on and came up with some very realistic prices for genuine kit.
smack said:
Busamav said:
if you do go ahead and try it your self ( and i wouldnt recomend it either )
Do not remove the chain untill you have the engine sprocket loosened off
To do the job you will need:Do not remove the chain untill you have the engine sprocket loosened off
Paddock stand
Hex / Alen keys
Screw drivers + and - ones
1/2 Drive socket set (with large sockets)
Possibly a bigger socket for wheel nut
Breaker Bar
Chain busting tool of your choice
Riveting tool
Big Hammer
Loctite
Torque wench
If your answer to anything on the list is "what's that", then take it to a shop. Or if your name is Chilli...
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff


