Chain tension
Author
Discussion

Rach*

Original Poster:

8,824 posts

247 months

Wednesday 22nd October 2008
quotequote all
I had my chain tightend before I left Scotland and have only ridden the 400 miles home, now its all baggy (alot baggy) again already.
Is that normal?

A bit ago my mate looked at my chain and said because he could move some things about in the centre of the chain it was about ready for replacing....

What's the BB opinion?

(also I'm skint and not found a job yet and getting a bit depressed frown)

catso

16,587 posts

298 months

Wednesday 22nd October 2008
quotequote all
If it's stretched that quickly then, unless you're a 'stunta' it's probably knacked.

Rach*

Original Poster:

8,824 posts

247 months

Wednesday 22nd October 2008
quotequote all
Bugger cry

Is that replacing spockets at the same time?

Edited by Rach* on Wednesday 22 October 15:37

Sossige

3,176 posts

294 months

Wednesday 22nd October 2008
quotequote all
Rach* said:
Bugger cry

Is that replacing spockets at the same time?

Edited by Rach* on Wednesday 22 October 15:37
I'd have thought it false economy not to Rach. Replace both sprockets and the chain together.

S

Rach*

Original Poster:

8,824 posts

247 months

Wednesday 22nd October 2008
quotequote all
He's running lumpy as anything too and the front pads are about ready for a change and I get front brake judder so the discs are probably foobarred aswell and there's 2 small oil leaks weeping





Carl-H

947 posts

237 months

Wednesday 22nd October 2008
quotequote all
LMAO at the 'baggy' chain. Your discs should not need changing (I've never had to change any but changed a fair few pads). I changed my chain and sprockets for less than £70 the other week doing the work my self. Not sure what everyone else pays but that was an O ring chain but not brilliant sprockets (only ones I could find for my bike though).

Steve_T

6,356 posts

303 months

Wednesday 22nd October 2008
quotequote all
Rach* said:
He's running lumpy as anything too and the front pads are about ready for a change and I get front brake judder so the discs are probably foobarred aswell and there's 2 small oil leaks weeping
Sucks to be you!

trumpet600

3,527 posts

262 months

Wednesday 22nd October 2008
quotequote all
Rach

You could always do the 'boomerang' test on your front disc.


Launch it through the air like a boomerang........if it doesn't come back to you it's knackered.

mitzy

13,858 posts

228 months

Wednesday 22nd October 2008
quotequote all
trumpet600 said:
Rach

You could always do the 'boomerang' test on your front disc.


Launch it through the air like a boomerang........if it doesn't come back to you it's knackered.
You been on the sauce ?

robstvr

3,217 posts

299 months

Wednesday 22nd October 2008
quotequote all
Check that your spindle nut is tight, and that the lock-nuts which prevent the wheel edging forwards have nothing untoward going on.

Rach*

Original Poster:

8,824 posts

247 months

Wednesday 22nd October 2008
quotequote all
trumpet600 said:
Rach

You could always do the 'boomerang' test on your front disc.


Launch it through the air like a boomerang........if it doesn't come back to you it's knackered.
Lol, don't tempt me!

Rach*

Original Poster:

8,824 posts

247 months

Wednesday 22nd October 2008
quotequote all
robstvr said:
Check that your spindle nut is tight, and that the lock-nuts which prevent the wheel edging forwards have nothing untoward going on.
Will do smile

Hooli

32,278 posts

231 months

Wednesday 22nd October 2008
quotequote all
vibey brakes is often just floating discs that arent floating on the bobbins rather than warped discs. where the disc attaches to the hub it'll have a righ of about 6 bobbins, they look like giant rivets (sorta). spray lots of brake cleaner on them & wiggle the disc in & out. whats ment to happen is the disc centers itself when you brake by moving on the bobbins, what actually happens is one sticks & disc runs off true.
pads are about £20 a caliper to do & easy enough. worth getting a mate to watch/advise if you've not done them before as brakes are sort of important.

if your chain is wearing that quick its either utterly fooked or something is causing it. a loose sprocket will eat the chain as will an out of line rear wheel. try pulling the chain straight backwards from the middle of the rear sprocket, if you can lift it more than a mm or two then it is knackered.

stick a post on that forum i sent you, there are a few people up your way & one of them even does quite a bit of cheap work on bikes for people. you'll probably find him happy to help for tea & cake.

y2blade

56,325 posts

246 months

Wednesday 22nd October 2008
quotequote all
Rach* said:
I had my chain tightend before I left Scotland and have only ridden the 400 miles home, now its all baggy (alot baggy) again already.
Is that normal?

A bit ago my mate looked at my chain and said because he could move some things about in the centre of the chain it was about ready for replacing....

What's the BB opinion?

(also I'm skint and not found a job yet and getting a bit depressed frown)
did you over tension it last time? should ALWAYS set the amount of slack as per the owners manual as each bike is differant.

if it's been over tensioned you may well have done bearing damage on the output shaft


Rach*

Original Poster:

8,824 posts

247 months

Wednesday 22nd October 2008
quotequote all
y2blade said:
Rach* said:
I had my chain tightend before I left Scotland and have only ridden the 400 miles home, now its all baggy (alot baggy) again already.
Is that normal?

A bit ago my mate looked at my chain and said because he could move some things about in the centre of the chain it was about ready for replacing....

What's the BB opinion?

(also I'm skint and not found a job yet and getting a bit depressed frown)
did you over tension it last time? should ALWAYS set the amount of slack as per the owners manual as each bike is differant.

if it's been over tensioned you may well have done bearing damage on the output shaft
I didnt tighten it I had it done at the bike shop

Rach*

Original Poster:

8,824 posts

247 months

Wednesday 22nd October 2008
quotequote all
Hooli said:
vibey brakes is often just floating discs that arent floating on the bobbins rather than warped discs. where the disc attaches to the hub it'll have a righ of about 6 bobbins, they look like giant rivets (sorta). spray lots of brake cleaner on them & wiggle the disc in & out. whats ment to happen is the disc centers itself when you brake by moving on the bobbins, what actually happens is one sticks & disc runs off true.
pads are about £20 a caliper to do & easy enough. worth getting a mate to watch/advise if you've not done them before as brakes are sort of important.

if your chain is wearing that quick its either utterly fooked or something is causing it. a loose sprocket will eat the chain as will an out of line rear wheel. try pulling the chain straight backwards from the middle of the rear sprocket, if you can lift it more than a mm or two then it is knackered.

stick a post on that forum i sent you, there are a few people up your way & one of them even does quite a bit of cheap work on bikes for people. you'll probably find him happy to help for tea & cake.
Will do, have to wait til I have enough pennies for the parts, seen a chain & sprocket set on ebay for £90, need to shop about a bit too smile

Hooli

32,278 posts

231 months

Wednesday 22nd October 2008
quotequote all
try proper shops too, i only paid £120 for chain & sprockets on my 14. i'd expect yours would be a bit cheaper.

Rach*

Original Poster:

8,824 posts

247 months

Wednesday 22nd October 2008
quotequote all
I need to find a local shop and make friends with them hehe

I feel sad now frown

Xenocide

4,286 posts

239 months

Wednesday 22nd October 2008
quotequote all
Virgin money are doing 0% interest for a while on their credit cards at the moment... smile

Roger McLittriss

493 posts

285 months

Wednesday 22nd October 2008
quotequote all
Could always be that the last shop let the trainee do it and he didn't bother to judge the wear on the chain before he adjusted it, and twiddled it at the slackest part of the chain run. So it wouldn't take much running to loosen it again, if you get me.

I always find it odd that given that chain drive is one of the most efficient means of transferring power from one place to another, and that multi-cylinder bikes have evenly-spaced power pulses, how the chain develops tight and slack spots. You could understand it on a single-cylinder!

It used to be cheaper to find an engineering suppliers' place that sold chain 'off the reel'; you just took the old chain in and they matched link size and length. Then chain and sprocket kits came along biggrin
Whilst it's true that fitting a new chain to old sprockets is verging on false economy, better a new chain wearing x% faster than normal than the old one snapping on take-off, if you're pushed for pennies (you could always do the chain this month and the sprockets next if you need the transport). Small-capacity bikes take a long time to wear the sprockets into hooks anyway so wear & tear, missed lubrication and the elements will do a chain in faster than the engine can.