Poor fuel economy
Poor fuel economy
Author
Discussion

lewis_sharman

Original Poster:

5,958 posts

222 months

Saturday 22nd November 2008
quotequote all
Just had a few alarm bells ringing in my head after reading a few posts on here about fuel economy.

Ive had the Chim for about 3 weeks now and so far havent had it above 17mpg (ive worked it out for 4 tankfulls and the worst one has been 13mpg!!!)

What could be causing this, as im assuming this is not right?

MADMAX2

2,336 posts

225 months

Saturday 22nd November 2008
quotequote all
Your heavy right foot?


whistle

lewis_sharman

Original Poster:

5,958 posts

222 months

Saturday 22nd November 2008
quotequote all
Ive been quite restrained actually, and the last tank i was being very cautious to see how good i could get the fuel economy as i thought it was quite low.

The wiring going into the AFM looks a tad ropey (as in i can see copper) but im not sure what they looked like from the factory. I will go get a picture if i can figure out photobucket to see what everyone thinks. Could this be the problem?

MADMAX2

2,336 posts

225 months

Saturday 22nd November 2008
quotequote all
I use my Chim every day 30 mins to work and 30 mins back home plus the usual blast when its dry. ive noticed shorter journeys DO use more fuel no matter how careful you can be.

chrispitman

742 posts

285 months

Saturday 22nd November 2008
quotequote all
Sounds abit low, 400's usually around 22-24Mpg. Used to get 22Mpg out of my 450 before the ecu change now running 18-19 Mpg but working to increase that a little.

lewis_sharman

Original Poster:

5,958 posts

222 months

Saturday 22nd November 2008
quotequote all



Does this look right to you?

ETA sorry for the poor picture quality, its a crap camera and only wanted to focus on the manifolds


Edited by lewis_sharman on Saturday 22 November 17:38


Edited by lewis_sharman on Saturday 22 November 17:41

V8 Animal

6,015 posts

241 months

Saturday 22nd November 2008
quotequote all
lewis_sharman said:
<a href="http://s499.photobucket.com/albums/rr353/lewis_sharman/?action=view&current=001.jpg" target="_blank"><img src="http://i499.photobucket.com/albums/rr353/lewis_sharman/001.jpg" border="0" alt="AFM"></a>

Does this look right to you?
NO
Copy and paste IMG on here.

lewis_sharman

Original Poster:

5,958 posts

222 months

Saturday 22nd November 2008
quotequote all
Sorry about that (first photo post)

GreenV8S

31,027 posts

315 months

Saturday 22nd November 2008
quotequote all
lewis_sharman said:
Does this look right to you?
No. That plug should have a shroud to protect it from the elements. The wiring shouldn't be exposed like that.

lewis_sharman

Original Poster:

5,958 posts

222 months

Saturday 22nd November 2008
quotequote all
GreenV8S said:
lewis_sharman said:
Does this look right to you?
No. That plug should have a shroud to protect it from the elements. The wiring shouldn't be exposed like that.
Do you know where i can get one?

HRG

72,863 posts

270 months

Saturday 22nd November 2008
quotequote all
GreenV8S said:
lewis_sharman said:
Does this look right to you?
No. That plug should have a shroud to protect it from the elements. The wiring shouldn't be exposed like that.
yes However unless you've got the right tools it'll be a pain to take the end off and get it back on. You can protect it with a liberal amount of Vaseline.

If you've got an extractor the sleeves are available here.

http://www.vehicle-wiring-products.eu/VWP-onlinest...

Not likely to cause the poor economy though.

Del 203

12,728 posts

280 months

Saturday 22nd November 2008
quotequote all
HRG said:
If you've got an extractor the sleeves are available here.

http://www.vehicle-wiring-products.eu/VWP-onlinest...

Not likely to cause the poor economy though.
Or just cut the wires & put small spade connectors on biggrin

HRG

72,863 posts

270 months

Saturday 22nd November 2008
quotequote all

V8 GRF

7,299 posts

241 months

Saturday 22nd November 2008
quotequote all
What colour are the insides of your exhausts? If they're covered in thick black soot then it's running rich and probably needs needs a decent service and the idle/mixture scre adjusting that and a combination of old plugs, dirty airfilter etc could result in excessive fuel consumption

lewis_sharman

Original Poster:

5,958 posts

222 months

Saturday 22nd November 2008
quotequote all
Just had new plugs, dizzy etc.

Will be getting a new air filter soon, and its going to the TDI dyno day on saturday so that shout give a descent representation of whats going on with it. I just didnt know if it could possibly be a duff sensor or something that i could check before i go?

V8 Animal

6,015 posts

241 months

Saturday 22nd November 2008
quotequote all
lewis_sharman said:
Just had new plugs, dizzy etc.

Will be getting a new air filter soon, and its going to the TDI dyno day on saturday so that shout give a descent representation of whats going on with it. I just didnt know if it could possibly be a duff sensor or something that i could check before i go?
TDI Dyno but's it's petrollaugh

lewis_sharman

Original Poster:

5,958 posts

222 months

Saturday 22nd November 2008
quotequote all
http://www.tdi-plc.com/thumbup

Edited by lewis_sharman on Saturday 22 November 19:18

blitzracing

6,422 posts

251 months

Saturday 22nd November 2008
quotequote all

The ecu should not let it run rich, even if the service items are worn, unless its a pre 92 car without a cat', when the AFM mixture screw makes a huge difference. Once the catalysts where fitted the ECU automaticaly adjusts the mixture, and the screw setting is ignored. Looking at you AFM wiring, I would not be surprised if the artfull bodger had been in there, and my first point of call would be borrow a fault code reader, and check the ECU is not in "fall back" mode. You would hardly know driving the car, but the fueling can be wrong. Unfortuantly in most cases the TVR does not have a working ECU warning light so you cant tell something is wrong. I would hold fire on the rolling road session until you have done this, as the only adjustment you can actually make is the ignition timing, and you dont need to simply be told "its running rich mate". Some reasons for running rich can normally be an AFM problem, excess fuel pressure, or a bad misfire.

Mark

lewis_sharman

Original Poster:

5,958 posts

222 months

Saturday 22nd November 2008
quotequote all
Next question then, who would be lovely enough to let me use their fault code reader? biggrin

I'm in the hertfordshire area but wouldnt mind a bit of a drive.

Or, failing that, where can i buy one and how much?

Edited by lewis_sharman on Saturday 22 November 21:06

hoach

49 posts

218 months

Saturday 22nd November 2008
quotequote all
There are two Lambda probes, one in each bank.

They measure the oxygen in the exhaust after combustion. It matters little how they work but understanding what they do is the best help in diagnosing fuel burning in the cylinders and therefore ‘mixture’ (air/fuel ratio).

Everyone who call themselves an expert (‘ex’ is a hasbeen and ‘spert’ is a drip under pressure) knows this, and it is simple.

Consider it magic in the absence of a detailed technical explanation. The exact mixture can be translated into a voltage that can be measured by the use of the cheapest voltmeter and translated into a signal that is always changing as the mixture is adjusted by the fuel injection computer.

If the voltage is less than 0.5volts on a scale of zero to one volt there is too much residual oxygen in the exhaust gas, therefore not enough fuel and so it is running week (not enough fuel for the amount of air)

If the voltage is above 0.5 volts the engine is running rich.

This is a true reading. Believe it, even though it looks like magic, when it works correctly it is magic!

The perfect running engine will produce a signal which changes continuously from above 0.5v to less than 0.5v, typically the voltmeter will read 0.76v then 0.2 then 0.81v then 0.34v. The best voltmeter to use is the old fashioned type, analogue, where you see a needle which moves over the scale. You can see the needle move up and down as the mixture changes. With a modern, common voltmeter it is not easy to visualise.

Which wire?

There are four wires to each probe on this engine and although I did this very thing a couple of days ago do not remember which wire is the correct one! No matter it is easy to find:

2wires are for the heater, 12v and earth (the probes have to be unbelievably hot to work and you would of though they would be hot enough where they are n the exhaust!!) I think they are both the same colour.

One other wire is earth.

The last wire is the signal wire which is what you need.

If you expose the wires you can put a small cut in the insulation, it is very tough stuff and needs some effort to expose the bare wire. Connect the voltmeter to this wire and a good earth and you should get a clear signal of zero to one volt.

Run the engine for at least 30 seconds to heat the probe

If you have no reading it is because: wrong wire, wrong setting on the voltmeter, bad earth or the probe s not working.

If it reads above 0.5 volts your engine is running rich.

If you have no luck try the other probe.

If you extend this wire into the cabin and connect t through a voltmeter to earth you can see the exact mixture when driving up to about 3,400 rpm when it will read above 0.5v, rich mixture. Please watch the road though. Earth s hard to find with a fibreglass tub, the outer part of the ciggy lighter s earth (and the centre is positive so don't short it!!)

I will be at work tomorrow, yes a Sunday, Teetertank s comming to see his chm but that s another and long story, look at my other posts and you will see how far have been into the fuel injection system!!

If you need any help over the phone 07833398695