A word of warning..............
Discussion
I booked my 99 Chimaera in for the usual pre winter chassis paint touch up/wax-oil, could se the normal bits chipped powder coat/paint, nothing to be concerned about, or so I thought. The car has spent the past five winters in a heated garage, it does about 4-5k a year, it hardly goes out in the winter, so I was taken aback by the level of corrosion to the tops of the out riggers (this could not be seen at all without lifting the body) anyway 14 feet of new steel tubing later we are looking good.
So my parting thought is, just because all looks well with parts you can see underneath dose not mean a clean bill of health
So my parting thought is, just because all looks well with parts you can see underneath dose not mean a clean bill of health
I guess that's the difference between DIY and paying someone else to do it for you. The job of looking after the tops of the outriggers with the body in situ is not a job for a slapdash one day merchant armed with a spray gun. It takes many hours of preparation and several fiddly techniques to get the tops cleaned, free of little road chippings and to be sure of a complete protective coating.
The one day merchants give a false sense of security. Everything looks good but they tend not to bother with the very fiddly, time consuming and dirty bits of the job.
The one day merchants give a false sense of security. Everything looks good but they tend not to bother with the very fiddly, time consuming and dirty bits of the job.
bobfather said:
I guess that's the difference between DIY and paying someone else to do it for you. The job of looking after the tops of the outriggers with the body in situ is not a job for a slapdash one day merchant armed with a spray gun. It takes many hours of preparation and several fiddly techniques to get the tops cleaned, free of little road chippings and to be sure of a complete protective coating.
The one day merchants give a false sense of security. Everything looks good but they tend not to bother with the very fiddly, time consuming and dirty bits of the job.
Completely agree... took me two full weekends of prep and another weekend to paint... and I wasn't hanging aboutThe one day merchants give a false sense of security. Everything looks good but they tend not to bother with the very fiddly, time consuming and dirty bits of the job.
bobfather said:
The job of looking after the tops of the outriggers with the body in situ is not a job for a slapdash one day merchant armed with a spray gun.
...
Everything looks good but they tend not to bother with the very fiddly, time consuming and dirty bits of the job.
Couldn't agree more. I had the option of getting mine done for ~£350 at a good TVR garage - on the understanding that the chassis was in good nick. But I thought I would do it myself, as I had some time on my hands and fancied getting under the car. Now, having seen the difficulty of getting it done well I don't think I will ever entrust the job to any garage. Not unless they are doing a body-off or I do not have the means to do it myself. ...
Everything looks good but they tend not to bother with the very fiddly, time consuming and dirty bits of the job.
Apart from maybe a touch up, I think the task is just too time consuming and fiddly to be done to my standards for any sane expense.
winters said:
bobfather said:
The job of looking after the tops of the outriggers with the body in situ is not a job for a slapdash one day merchant armed with a spray gun.
...
Everything looks good but they tend not to bother with the very fiddly, time consuming and dirty bits of the job.
Couldn't agree more. I had the option of getting mine done for ~£350 at a good TVR garage - on the understanding that the chassis was in good nick. But I thought I would do it myself, as I had some time on my hands and fancied getting under the car. Now, having seen the difficulty of getting it done well I don't think I will ever entrust the job to any garage. Not unless they are doing a body-off or I do not have the means to do it myself. ...
Everything looks good but they tend not to bother with the very fiddly, time consuming and dirty bits of the job.
Apart from maybe a touch up, I think the task is just too time consuming and fiddly to be done to my standards for any sane expense.
BIG COL said:
I hear what you guys are saying, but for the life of me, I can't see how you can check the tops of the out riggers?
There is lots to be seen by looking from the wheel arches and it is possible to ascertain the condition of blind parts by feel using home made scrapers and the like.I insist on removal of wheels for this inspection whenever I am asked to view a car for purchase. It's a requirement of purchase, I now ask the owner for this level of access prior to setting off for a viewing.
Making yourself sound like a voyeur Bob 
But TBH the Sportmotive replacement outriggers surely make this less of a worry than it always used to be? There must be a lot of rotten ones out there judging by the 'only took me halfaday' posts we've seen
Of more concern to me would be the upper tubes under the manifolds if I was looking for a car

But TBH the Sportmotive replacement outriggers surely make this less of a worry than it always used to be? There must be a lot of rotten ones out there judging by the 'only took me halfaday' posts we've seen

Of more concern to me would be the upper tubes under the manifolds if I was looking for a car

BIG COL said:
I hear what you guys are saying, but for the life of me, I can't see how you can check the tops of the out riggers?
I'm not sure you can without the body off/up.... but with axle stands, mirrors, peeking down the outrigger tops/ends, running screw drivers, chisels, bent hack saw blades, emmery paper etc over tubes/into nooks and crannies you can have a pretty good stab. Then painting with bits of bent metal with foam pads, artist paint brushes, shoelaces, cable ties over the tubes and a lot of patience will get you a decent way. The only bits on Floyds pics I haven't inspected are the areas of contact between metal/fibre glass on the horizontal/vertical mounting plates - because the body is sitting on them. It's suprising how much you can see with the right lighting; inspection lights/torches. e.g. looking down the two gaps between the body/tubes above each mounting plates you can see the tops and inner corners of the two tubes.
All this said you cant give it a full structural test - i.e. smack it with a hammer/chisel. And that's why I may well do a body-up/off next year to be sure. I expect how well you can do somewhat depends on the state of the metal/paint before you start and how your body happens to sit on the plates/tubes.
Was a pig of a job - still not quite finished - but I'm sure no garage would go to the same lengths. Not for a day's labour anyway.
Oh, I think painting with expoxy mastic helped too. It going on thick helped to get good coverage in a couple of coats, even with my bizzare painting tools (true in the coldish temperatures I did it in anyway). One of the most useful tools i used was an uncleaned artists brush with the bristles all stiff/splayed out. Sticking it in holes and spinning/wacking it around helped to get a lot of the tricky areas you can see holes in above.
Pink_Floyd said:
A couple of pics of my 1998 chassis. Not easy to see the holes from Underneath.



Scary what you can't see. I don't think that any amount of on the bottom of the frame would have stopped this rust.
Thanks - I'll be booking my '98 Chimaera into TopCats for a full chassis 'top & tail' very shortly...


Scary what you can't see. I don't think that any amount of on the bottom of the frame would have stopped this rust.
Pink_Floyd said:
A couple of pics of my 1998 chassis. Not easy to see the holes from Underneath.



Scary what you can't see. I don't think that any amount of on the bottom of the frame would have stopped this rust.
No,but looking at the rest of the chassis is a good indicator,and your looks sore even from the uprights and those body mounting plates gives you an indication that all is not well with this one,no offense like 


Scary what you can't see. I don't think that any amount of on the bottom of the frame would have stopped this rust.
Edited by Pink_Floyd on Sunday 21st December 20:38

That Daddy said:
Pink_Floyd said:
A couple of pics of my 1998 chassis. Not easy to see the holes from Underneath.



Scary what you can't see. I don't think that any amount of on the bottom of the frame would have stopped this rust.
No,but looking at the rest of the chassis is a good indicator,and your looks sore even from the uprights and those body mounting plates gives you an indication that all is not well with this one,no offense like 


Scary what you can't see. I don't think that any amount of on the bottom of the frame would have stopped this rust.
Edited by Pink_Floyd on Sunday 21st December 20:38

Even if the bits you can see look okay, don't think because its been waxoyl'ed it's okay... mine wasn't!
http://www.pistonheads.co.uk/gassing/topic.asp?h=0...
http://www.pistonheads.co.uk/gassing/topic.asp?h=0...
TVR Moneypit said:
tvrforever said:
Pink_Floyd said:
Thanks - I'll be booking my '98 Chimaera into TopCats for a full chassis 'top & tail' very shortly...Gassing Station | Chimaera | Top of Page | What's New | My Stuff





