Full Poly Bushing?
Discussion
As the handling is getting a little tired on my chim, I was thinking of doing the full Steve Heath Poly Bush bundle 3b including the drop links etc. Just wondered if anybody else had gone the "whole Hog" and what the labour cost would be roughly. Fitted Gaz shocks last year which I am happy with, but I do get various knocking noises etc which I am guessing may be worn bushes etc. Car is a 1997 4.0 with 35k on the clock.
i changed the top and bottom ball joints and both track rod ends , could not beleive the difference and got rid of a clonk noise .the mechanic did the whole job in two hours .i changed my rear drop links only last year and on inspection they have split again .i went for steve heath front drop links but every car is a little different fitting can be awkward , adding and removing washers ,getting the correct angle of fittment etc .you can snap them easy!
I'm just contemplating the same thing I've stripped the front suspension down and lifted the body. half way through cleaning the crap off it. Dont know whether to put original rubber or poly bushes back though they aint cheap compared to the originals. The rubber have lasted well my 1998 47K miler dont look bad at all. Just I will be removing them to have the wishbones plasic coated.
Wheres the cheapest place you have found? Possible bulk buy?
Penno
Wheres the cheapest place you have found? Possible bulk buy?
Penno
If you are going to the trouble of removing old metelastic bushes, poly replacements are the obvious choice.
Better handling
No preload issues
Dead easy to replace
Powerflex seem a breed apart from the other polybushes as well.
As for labour cost, I cannot answer that as I did them myself.
Better handling
No preload issues
Dead easy to replace
Powerflex seem a breed apart from the other polybushes as well.
As for labour cost, I cannot answer that as I did them myself.
blujay10 said:
As the handling is getting a little tired on my chim, I was thinking of doing the full Steve Heath Poly Bush bundle 3b including the drop links etc. Just wondered if anybody else had gone the "whole Hog" and what the labour cost would be roughly. Fitted Gaz shocks last year which I am happy with, but I do get various knocking noises etc which I am guessing may be worn bushes etc. Car is a 1997 4.0 with 35k on the clock.
I'm just completing the 'whole hog' upgrade with poly bushes, SH droplinks,shocks and track rod ends. Replacing the bushes is not easy as has been stated on here before, but it's not rocket science and once you get a system going and stick at it, it's soon done and you're quids in! Replacing the other parts is straightforward.
Mine is a 1996 and one of the shocks was leaking,and the ARB bushes knackered (MOT'd last month???)
I can't comment on the handling until it's had the suspension set up and geo carried out but I expect it to be transformed and I'll post my comments on here.
Bm
have alook at this http://cgi.ebay.co.uk/TVR-GRIFFITH-CHIMERA-SUPERFL...
Just in the process of fitting new Powerflex bushes to my chim.
If anyone needs any info I suggest you speak to Trackcar Solutions, very informed guy.
Fitting takes longer then expected, but very do-able.

Looking forward to completion!
Fitted Powerflex bushes,
Refurbed wishbones,
Braided hoses,
New rear calipers,
Serviced dampers.
Cheers,
HCM.
If anyone needs any info I suggest you speak to Trackcar Solutions, very informed guy.
Fitting takes longer then expected, but very do-able.

Looking forward to completion!
Fitted Powerflex bushes,
Refurbed wishbones,
Braided hoses,
New rear calipers,
Serviced dampers.
Cheers,
HCM.
daz the plumber said:
don`t think they need to any harder,there a harsh ride any way !so are the grades identified by the colour?
Not necessarily and it also depends on which make you get. As it has already been said, I do the Powerflex ones as they have developed special versions for the Griff Chimaera which include special split bushes and ones with heat shields which are essential to get a good fit and ensure that the bushes last. They also only do one grade.
The real problem with doing them is to get the old ones out. Problems include seized bolts and the usual rounded heads which often means they have to be cut away and then replaced. The number of times I've been called with a "I've had to cut such and such bolt and B&Q don't have them and I need the car on the road tomorrow" is quite incredible... which is why I bundle the bolts/nuts with the bushes so you have everything that is needed. Getting the bushes out of the wishbones themselves which can be a struggle. Techniques to do this are covered in the bible and the fitting instructions that come with the bushes. If you can get access to a press then that can speed up the process but if the old bush is seized into the wishbone then it will need cutting out. With 20 bushes to do front and rear, it can take some time. It is not a difficult job technically but can be frustrating and time consuming.
shpub said:
Problems include seized bolts and the usual rounded heads which often means they have to be cut away and then replaced. The number of times I've been called with a "I've had to cut such and such bolt and B&Q don't have them and I need the car on the road tomorrow" is quite incredible... which is why I bundle the bolts/nuts with the bushes so you have everything that is needed.
Maybe you should sell some odd AF sockets & spanners Steve, they might buy them from you? haircutmike said:
Just in the process of fitting new Powerflex bushes to my chim.
If anyone needs any info I suggest you speak to Trackcar Solutions, very informed guy.
Fitting takes longer then expected, but very do-able.

Looking forward to completion!
Fitted Powerflex bushes,
Refurbed wishbones,
Braided hoses,
New rear calipers,
Serviced dampers.
Cheers,
HCM.
Is there a bit of crud build up behind the chassis rail corner, directly above your scissor jack?If anyone needs any info I suggest you speak to Trackcar Solutions, very informed guy.
Fitting takes longer then expected, but very do-able.

Looking forward to completion!
Fitted Powerflex bushes,
Refurbed wishbones,
Braided hoses,
New rear calipers,
Serviced dampers.
Cheers,
HCM.
"Is there a bit of crud build up behind the chassis rail corner, directly above your scissor jack?"
Well spotted, car going in to Mole Vally TVR soon for a chassis clean and Waxoyl.
Finished assembling everything this morning, just have to adjust handbrake, bleed brakes and set camber angles.
Can't wait to try her out!
HCM.
Well spotted, car going in to Mole Vally TVR soon for a chassis clean and Waxoyl.
Finished assembling everything this morning, just have to adjust handbrake, bleed brakes and set camber angles.
Can't wait to try her out!
HCM.
"IIRC Ride height should be done first as it affects the camber, then camber as it affects tracking and finally tracking. All with suspension under load of course!"
Agree, Got mine on the road this afternoon, Yahee, new bushes, brake hoses, calipers etc.
Have set everything as before but will book into local tiv dealer for final adjust.
HCM.
Agree, Got mine on the road this afternoon, Yahee, new bushes, brake hoses, calipers etc.
Have set everything as before but will book into local tiv dealer for final adjust.
HCM.
Thanks for all the replies, Gentlemen. I think I'll go the Steve Heath route and buy the complete bundle. Not sure who I'll ask to fit yet....well that was the plan until my rear screen blew out yesterday.......hopefully I can get that on the insurance (Hagerty) and then the ploy bushing will be back on track!
Look forward to hearing how badmutha and haircutmike get on and what the difference is.
Cheers,James
Look forward to hearing how badmutha and haircutmike get on and what the difference is.
Cheers,James
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



