Rear Brake Pads Chim - Straightforward Fitting ?
Rear Brake Pads Chim - Straightforward Fitting ?
Author
Discussion

Andy JB

Original Poster:

1,321 posts

250 months

Monday 19th January 2009
quotequote all
I plan to fit my own rear upgraded brake pads on Chim 500 to match the front pads/discs completed easily last year.

I have read somewhere this is not a straightforward job on the rear. Can anyone on here confirm what sort of job this and why this may be not for the home mechanic? Is there a probelm with rear handrake mechanism?

Any advice appreciate or an idiots guide most welcome before i start.

dogbucket

1,256 posts

232 months

Monday 19th January 2009
quotequote all
Only complication is that the pistons must be wound back into the caliper. Worth getting the proper tool to do that rather than struggling with other methods, about £10-15 in Halfords.

Overhere

382 posts

254 months

Monday 19th January 2009
quotequote all
I agree with Dog, get the tool, you can borrow mine if you want to come to Winchester and pick it up. Otherwise no big deal. The Bible has instructions, as would a Haynes mid 90's Sierra manual, but to be honest it's pretty straight forward if you've done brakes before. Also use EZ Bleed, another great tool.

drlloyd

145 posts

224 months

Monday 19th January 2009
quotequote all
Just did this job on my 400 HC. Top tip: Buy a calliper piston wind-back tool and wind the calliper piston in CLOCKWISE. I was uncertain and started winding one calliper piston anti-clockwise, this let in some air and meant that I had to bleed the entire braking system. It did take an age to wind the piston in correctly as well, even with the piston winding tool!

Apart from that the job wasn't too bad.

drlloyd

145 posts

224 months

Monday 19th January 2009
quotequote all
Oh and if you do need or want to bleed the brakes, EZ bleed is invaluable.

spend

12,581 posts

282 months

Monday 19th January 2009
quotequote all
My wind back tool puts the pressure on as well, but I never use that part of it, just open the bleed valve & dump the crap boiled fluid at the same time wink

spend

12,581 posts

282 months

Monday 19th January 2009
quotequote all
Quinny said:
spend said:
My wind back tool puts the pressure on as well, but I never use that part of it, just open the bleed valve & dump the crap boiled fluid at the same time wink
My wind back tool is a pair of pipe gripsyikeshehe

Hence the G clamp
What with a big Posh ramp I guess all you need are stilsons & a big hammer tongue outrofl

V8 Animal

6,015 posts

241 months

Monday 19th January 2009
quotequote all
The 8mm cap bolt at the top of the caliper can be a bit tricky you won't get a socket on it use a lever on the key.
Did mine on saturday and the fronts.
V8 Animal

Pasco

6,652 posts

259 months

Monday 19th January 2009
quotequote all
Quinny said:
fk off, I've got an adjustable spanner, and a lever, that turns into a screwdriver (or is that a screwdriver that turns into a lever??)

Either way I have a full tookit thankyou very muchyes
Which Ain't much good according to your Misses you Old Git !!! hehe

Del 203

12,728 posts

280 months

Monday 19th January 2009
quotequote all
Pasco said:
Quinny said:
fk off, I've got an adjustable spanner, and a lever, that turns into a screwdriver (or is that a screwdriver that turns into a lever??)

Either way I have a full tookit thankyou very muchyes
Which Ain't much good according to your Misses you Old Git !!! hehe
rofl x 10000000000


Mrs P said the same about you tubbs wink

spend

12,581 posts

282 months

Monday 19th January 2009
quotequote all
Tubbs... Mirror.... x10000000000000 times / day whistlewhistlewhistlewhistlewhistle