Discussion
Hi Guys. Planning a service this weekend and am very confident in everything that needs to be done except oil and filter change. Not sure about the oil pump priming - have been told that providing I,m quick should not have this problem. Engine is pre serpentine and runs perfect with good oil pressure. Should I expect to prime the pump, and get the additional gasket now to remove the pump cover ? Many thanks - Beastmaster
Fill the oil filter before you start, they literally can take hours to fill... Each time it appears full, 10-30 mins later you will be able to top up.... until it is full. I reckon that gives you a lot better safety margin against priming issues. Downside is you have to spin it on very quickly and its a fair bit heavier 
That has always seemed a more important step to me even than the 'method/theory' of squirting oil up the middle of the spin-on if you have priming problems.

That has always seemed a more important step to me even than the 'method/theory' of squirting oil up the middle of the spin-on if you have priming problems.
I had a discussion with Pete Humphries about this a while back and he suggested it was better to have an empty filter - so that the pump has no resistance against it on the output side when initially pulling oil from the sump.
I think I'm with him on this one, though I think we could discuss this for and aginst till the cows come home.
I think I'm with him on this one, though I think we could discuss this for and aginst till the cows come home.
Edited by Barkychoc on Friday 30th January 10:28
I would certainly advocate pumping oil into the pump side (PRV) in preference to the engine side (middle of spin-on) if you have priming problems 
Must admit I have never felt confident in the priming by having oil for the pump to work against (there was an old thread where I raised this - which gets misquoted fairly regularly by DorninMeinerSeite)
Do Note: both Peter & I have slightly different 'challenges' as we both run oil coolers & remote stats. Don't know about Peter, but I do drain down my cooler at oil changes, as well as the accumulator... There is potential for an awful lot of air and quite a delay from firing to oil delivery in those situations. I guess that is why we both use drill pumps to pre-oil?
I see no reason why the cheap drill pumps could not be used on std engines, just suck from the timing cover & dump it in the rocker cover oil filler. Some pipe and connector to stick in one of the M20 serp blanking plugs / pre-serp tappings must be cheaper & easier than the dizzy drill priming tools?

Must admit I have never felt confident in the priming by having oil for the pump to work against (there was an old thread where I raised this - which gets misquoted fairly regularly by DorninMeinerSeite)
Do Note: both Peter & I have slightly different 'challenges' as we both run oil coolers & remote stats. Don't know about Peter, but I do drain down my cooler at oil changes, as well as the accumulator... There is potential for an awful lot of air and quite a delay from firing to oil delivery in those situations. I guess that is why we both use drill pumps to pre-oil?
I see no reason why the cheap drill pumps could not be used on std engines, just suck from the timing cover & dump it in the rocker cover oil filler. Some pipe and connector to stick in one of the M20 serp blanking plugs / pre-serp tappings must be cheaper & easier than the dizzy drill priming tools?
spend said:
I would certainly advocate pumping oil into the pump side (PRV) in preference to the engine side (middle of spin-on) if you have priming problems 
Must admit I have never felt confident in the priming by having oil for the pump to work against (there was an old thread where I raised this - which gets misquoted fairly regularly by DorninMeinerSeite)
Do Note: both Peter & I have slightly different 'challenges' as we both run oil coolers & remote stats. Don't know about Peter, but I do drain down my cooler at oil changes, as well as the accumulator... There is potential for an awful lot of air and quite a delay from firing to oil delivery in those situations. I guess that is why we both use drill pumps to pre-oil?
I see no reason why the cheap drill pumps could not be used on std engines, just suck from the timing cover & dump it in the rocker cover oil filler. Some pipe and connector to stick in one of the M20 serp blanking plugs / pre-serp tappings must be cheaper & easier than the dizzy drill priming tools?
Bloody hell Spend,bet you love oil&filter change time on your car 
Must admit I have never felt confident in the priming by having oil for the pump to work against (there was an old thread where I raised this - which gets misquoted fairly regularly by DorninMeinerSeite)
Do Note: both Peter & I have slightly different 'challenges' as we both run oil coolers & remote stats. Don't know about Peter, but I do drain down my cooler at oil changes, as well as the accumulator... There is potential for an awful lot of air and quite a delay from firing to oil delivery in those situations. I guess that is why we both use drill pumps to pre-oil?
I see no reason why the cheap drill pumps could not be used on std engines, just suck from the timing cover & dump it in the rocker cover oil filler. Some pipe and connector to stick in one of the M20 serp blanking plugs / pre-serp tappings must be cheaper & easier than the dizzy drill priming tools?
still its worth having the fuel accumulator system and oil cooler fitted as you know,i wont take changing my oil & filter simplicity for granted next time 
Of course you dont need to answer this Spend.
Edited by That Daddy on Friday 30th January 12:11
Gassing Station | Chimaera | Top of Page | What's New | My Stuff




