Main cat removal?
Discussion
Ive brought a second hand y piece on the cheap (as i cant afford clives y piece at the moment
)
The plan is to remove the cat add a wideband bung and wrap in exhaust wrap to reduce the tinnyness.
Will i need to change the tune resistor? its currently white from memory.
I know its been done loads of times but i cant find a straight answer
)The plan is to remove the cat add a wideband bung and wrap in exhaust wrap to reduce the tinnyness.
Will i need to change the tune resistor? its currently white from memory.
I know its been done loads of times but i cant find a straight answer

Depends on the rest of the system. If you have a sleeved/bombed main 'silencer' then the big cat is the main silencing component and it will be loads louder without it. If with the oem box then it will be fine if a bit more 'pingy' sounding due to the increased resonance in the big hollow space where the cat was. I found the manifold cats had no effect (that I could discern) on noise but had a major effect on under-bonnet temperature (as does the main one). No brainer to have 'em out
Mine is/was far too noisy for comfort, I just stuck the cat back in. Yes, old fart I know 
If you are hacking the cat out & sensoring, you could try coning the 'dustbin' down to the outlet pipe rather than leaving it cylindrical. The change in shape might just take the edge off the resonance? I've not seen / tried that - just wondered in idle moments
My Lucas ran better if anything with the cat resistor anyway as far as I could tell from the short time I tried it. As with most things the engines seem quite different in tune and sound so YMMV..

If you are hacking the cat out & sensoring, you could try coning the 'dustbin' down to the outlet pipe rather than leaving it cylindrical. The change in shape might just take the edge off the resonance? I've not seen / tried that - just wondered in idle moments

My Lucas ran better if anything with the cat resistor anyway as far as I could tell from the short time I tried it. As with most things the engines seem quite different in tune and sound so YMMV..
spend said:
you could try coning the 'dustbin' down to the outlet pipe rather than leaving it cylindrical. The change in shape might just take the edge off the resonance?
I was thinking along them lines but wont know if its possible (or im capable
) untill i open her up. Ill post up my progress if theres any interest.
Remember to tell your insurance company, as it counts as a major modification, some will not even continue your insurance if you do this, I asked and they frowned, so I didn't.
Importantly, if you do it, tell them, or they have a good reason not to pay any claim you make, pre cat removal is neither here nor there.
Importantly, if you do it, tell them, or they have a good reason not to pay any claim you make, pre cat removal is neither here nor there.
Meatball said:
spend said:
you could try coning the 'dustbin' down to the outlet pipe rather than leaving it cylindrical. The change in shape might just take the edge off the resonance?
I was thinking along them lines but wont know if its possible (or im capable
) untill i open her up. Ill post up my progress if theres any interest.
Ive cut the exhaut in half and see what you mean now...im wondering would it be easier to to cut at the lower join just before the bend an have a piece made like you say in a cone shape and join the 2 together (christ its starting to sound like a frankenstein version of clives masterpiece
)or
weld another layer inside the main drum to try and cut down the tinnyness (cheap and easy option).
Any tips on how to get the cat out?
Meatball said:
Pupp said:
The cat tune resistor (and map) will work just fine with the cat out; it's actually the best choice. On mine I needed to slightly tweak the trimmer on the AFM but there are those who say it has no effect (on mine it did)
Pupp does it sound much louder without the main cat?
Its not that loud

Well, not in the car anyway

Meatball said:
Meatball said:
spend said:
you could try coning the 'dustbin' down to the outlet pipe rather than leaving it cylindrical. The change in shape might just take the edge off the resonance?
I was thinking along them lines but wont know if its possible (or im capable
) untill i open her up. Ill post up my progress if theres any interest.
Ive cut the exhaut in half and see what you mean now...im wondering would it be easier to to cut at the lower join just before the bend an have a piece made like you say in a cone shape and join the 2 together (christ its starting to sound like a frankenstein version of clives masterpiece
)or
weld another layer inside the main drum to try and cut down the tinnyness (cheap and easy option).
Any tips on how to get the cat out?
spend said:
2 cuts to remove the cat section, & cut a sheet that will wrap to form a cone from top to bottom would be my suggestion. Ask Clive he may give you some tips? Its not flowed as well as the proper ones, but must be better than just hacking the cat out the bin?
What problem is the cone intended to solve? The only reason I can see is to make the exit a bot smoother, but if you look at the shape of the outlet it's already nicely smoothed out. If you think about it, the cat is just a set of parallel tubes filling the middle of the Y piece and does nothing much for the flow in or out, so there's no reason to expect any gas flow problems after you remove the cat.We are discussing noise implications when removing the cat internals from the dustbin Peter?
Are you on about the separator Ben, you need something to stop the opposing pulses at the Y hitting each other. Thats the advantage of aftermarket replacements - they bend it round a bit more.. I'm not sure what you could do to improve it TBH?
Gradually reducing the dia from your 2 cuts should defeat some of the sound, you could even try packing it externally with wadding and cover with the original 'dustbin' cylinder shape (but it makes the WB sensor bung a little trickier
). Mine did boom at certain frequencies, which I rightly / wrongly put down to standing waves and figured a non uniform cross section area might defeat these rather than amplify them 
Are you on about the separator Ben, you need something to stop the opposing pulses at the Y hitting each other. Thats the advantage of aftermarket replacements - they bend it round a bit more.. I'm not sure what you could do to improve it TBH?
Gradually reducing the dia from your 2 cuts should defeat some of the sound, you could even try packing it externally with wadding and cover with the original 'dustbin' cylinder shape (but it makes the WB sensor bung a little trickier
). Mine did boom at certain frequencies, which I rightly / wrongly put down to standing waves and figured a non uniform cross section area might defeat these rather than amplify them 
spend said:
Are you on about the separator Ben, you need something to stop the opposing pulses at the Y hitting each other. Thats the advantage of aftermarket replacements - they bend it round a bit more.. I'm not sure what you could do to improve it TBH?

Ive not made my mind up 100% but was thinking along the lines of welding the 2 deflectors together at the open end.
Ive got access to a precision engineer at work so may pick his brain to whats possible.
Im also tempted to just try excessively exhaust wrapping the y piece to try to keep the additional noise a little more tame. I dont have a clue if wrap will achieve this?
The problem is im trying to do this on the cheap and dont really want to get into additional fabricating and welding.
BTW any suggestions on how to get the cat out without the use of a press or grown ups tools

My caveman expertise didnt work

Appreciate your input
Gassing Station | Chimaera | Top of Page | What's New | My Stuff




