Steel rockers
Steel rockers
Author
Discussion

Barkychoc

Original Poster:

7,848 posts

235 months

Monday 9th February 2009
quotequote all
When I finally get round to putting my engine back together I'm going to need rockers & shafts as a minimum on the top end.

I've seen steel ones advertised in a few places - can I assume due to the lack of threads (none) that I have found on these they are best avoided?
You don't want more weight in the valve train anyway do you?

I planned to go for standard rockers - I assume the steel ones are around because they can be made cheaply and no other reason?
Or am I missing something?

slideways

4,101 posts

252 months

Monday 9th February 2009
quotequote all
V8 Developments put steel ones on mine they said there better than original

Noogly

424 posts

301 months

Tuesday 10th February 2009
quotequote all
would the original rockers be some cheap/light alloy?

Johno

8,593 posts

313 months

Tuesday 10th February 2009
quotequote all
Steel are preferable as they do not suffer with premature lost pads which can be an issue with alloy ones.

It is not a common problem, but it does occur occassionally. It has been discussed several times on the forums but the search facility only goes back 2 yrs and that's classified as Jan '09 and all of 08 . . Also don't confuse the valve gear in a TVR RV8 with a TVR SP6 . . . very different in terms of quality hehe

Next up the tree are roller rockers which then take away the side loading on the top of valve.

clive f

7,259 posts

264 months

Tuesday 10th February 2009
quotequote all
definately a vote for steel here as well, I replaced my standard ones because one of the pads came away from the rocker, then only 400 miles later found 3 of the new ones had lost their pads!! threw them in the bin and bought steel ones, fit and forget scenarioyes
I have some roller rockers if you`re interested.

Edited by clive f on Tuesday 10th February 14:22

Barkychoc

Original Poster:

7,848 posts

235 months

Tuesday 10th February 2009
quotequote all
Who makes the steel rockers?
I've seen unbranded ones on ebay (cheap) - plus other unbranded ones at various land rover outlets - is there a particular make out there to go for?
Are they all much of a muchness?

I'm assuming not and the cheap ones are rubbish?

clive f

7,259 posts

264 months

Tuesday 10th February 2009
quotequote all

spend

12,581 posts

282 months

Tuesday 10th February 2009
quotequote all
If you are changing the rockers, its odds on the shafts will be worn as well.... then roundness of the posts... wink

Dom replied to a thread on here a couple of years ago that he was happy with the alloy rockers and that problems were down to a 'bad' batch. Personally I would always prefer lighter alloy to cut weight in the valvetrain, but each to their own there is not such a great deal in it..

dhf

1,103 posts

225 months

Tuesday 10th February 2009
quotequote all
Clive,what are the benefits of your roller rockers ?

spend

12,581 posts

282 months

Tuesday 10th February 2009
quotequote all
He will be able to raise some some cash with them hehe

Barkychoc

Original Poster:

7,848 posts

235 months

Tuesday 10th February 2009
quotequote all
spend said:
Personally I would always prefer lighter alloy to cut weight in the valvetrain
That was certainly my thought Dave - but I don't claim to be any kind of expert on this.

clive f

7,259 posts

264 months

Tuesday 10th February 2009
quotequote all
dhf said:
Clive,what are the benefits of your roller rockers ?
no friction so more power, the rollers roll over the top of the valve head, and the preload, valve crearance, can be adjusted at the top of the rocker, these are more of a benefit to someone with solid lifters, as then to check valve clearances you dont have to remove the inlet manifold and valley gasket to check the pre load on the lifters as with the normal proceedure for hydraulic lifters.
a benefit really to any type of lifters, and increase in power output.

dhf

1,103 posts

225 months

Tuesday 10th February 2009
quotequote all
you lost me there Clive,very early on in the paragraph ! so if i had just split my engine what other parts would i need along with yours ? what sort of power gains could one expect ?

spend

12,581 posts

282 months

Tuesday 10th February 2009
quotequote all
The roller rockers 'roll' across the valve stem rather than 'hammering' across it. Many come with adjusters, which you can use with mechanical setups (set valve clearances) or set the preload for hydraulic followers.

GreenV8S

31,027 posts

315 months

Tuesday 10th February 2009
quotequote all
clive f said:
dhf said:
Clive,what are the benefits of your roller rockers ?
no friction so more power,
The main advantage is that it lets you run a very high lift cam without causing excessive wear. Otherwise the side loads on the valve stem and wear between the valve and rocker are limiting factors. If you don't need them to solve those problems then it's a lot of expense and valve train weight that you could do without.

spend

12,581 posts

282 months

Tuesday 10th February 2009
quotequote all
Where does this 'they are heavier' come from? Have you actually compared the weights?

clive f

7,259 posts

264 months

Wednesday 11th February 2009
quotequote all
not weighed them, but I`d say they were a bit lighter than the steel rockers.

dermot, YHM

Edited by clive f on Wednesday 11th February 07:25

rev-erend

21,624 posts

315 months

Wednesday 11th February 2009
quotequote all
They also look nicer biggrin


dhf

1,103 posts

225 months

Wednesday 11th February 2009
quotequote all
Clive,thanks understand it all now.i am actually installing a tame cam for the supercharger.

Barkychoc

Original Poster:

7,848 posts

235 months

Wednesday 11th February 2009
quotequote all
dhf said:
Clive,thanks understand it all now.i am actually installing a tame cam for the supercharger.
I think thats a requirement isn't it?

My understanding is if you have a lairy cam with overlap (where both exhaust and inlet valves are open at the same time) the pressurised induction blows your fuel / air mixture straight out the exhaust?
Have I interpreted this correctly?