Wheel speed sensors
Discussion
You have triggers on the rear wheels with the BTR diff just need to add sensors. There is Ford front hub assembly that has the sensor bolt into the hub and the stub has an integrated trigger wheel. That would be an 'engineered' solution from factory components, but I believe many can just sense off studs or whatever is to hand.
As Spend says, the uprights have provision for wheel speed sensors but the ones TVR use haven't got the sensor mounting holes drilled and tapped. So you can just swap the uprights for the equivalent from a posher model with ABS.
Would you go for spark cut? I guess fuel cut on a turbo could be disasterous. Can you do anything to dump the boost before you introduce misfires?
Would you go for spark cut? I guess fuel cut on a turbo could be disasterous. Can you do anything to dump the boost before you introduce misfires?
HRG said:
Worth contacting Steve Heath? He has a 'bolt on' setup for use with Racelogic I believe.
Yep thats what I am fitting at the moment, do you know can you get to the speed sensor on the diff you jack up the backend or is it better on a ramp ?, also what ECU are you using Vxp ? I have the sensor details if you need them.hiltonig said:
HRG said:
Worth contacting Steve Heath? He has a 'bolt on' setup for use with Racelogic I believe.
Yep thats what I am fitting at the moment, do you know can you get to the speed sensor on the diff you jack up the backend or is it better on a ramp ?, also what ECU are you using Vxp ? I have the sensor details if you need them.
)Peter, its a torque reduction strategy, uses a mix of ign retard and graduated fuel cut to prevent knock. Can also be run with steering angle or Lateral G sensors.
Vixpy1 said:
Peter, its a torque reduction strategy, uses a mix of ign retard and graduated fuel cut to prevent knock. Can also be run with steering angle or Lateral G sensors.
I suppose it depends how much torque you need rid of, but from the sound of it you'll need to lose a lot to be effective. Isn't late/lean going to get the chamber and exhaust ports very hot? Especially for an FI setup I'd have thought you would prefer to avoid that.OK....
Lots of answers:
1. Diff sensor can be accessed on a ramp or on axle stands. Done it both ways.
2. I do a bracket/sensor kit for the Cerbera but I could adapt it to fit a Chimaera.
3. I use the Racelogic TC setup because I haven't yet seen anything else built into an ECU that gets anywhere near it. There's a challenge for you! It is extremely sophisticated in how it determines what the car is doing and when and when not to come in. It simply cuts injectors. The number of injectors that can be cut is programmable and it distributes the cuts around the cylinder/injectors so that any effect is evened out. It uses several different levels which can be programmed for different levels of wheel slip. You need some wheel slip for optimum grip. To be honest, to control the 500+ bhp I have, the cuts are quite aggressive. If they are not aggressive enough, the system will not respond quickly enough and the TC may cause more problems than it solves.
I have been running it on my Wedge for 10+ years. The last 2-3 with a Vortech blower producing around 540 bhp. The engine was stripped down last week in preparation for a boost increase and again, no problems so the Racelogic system certainly works.
Lots of answers:
1. Diff sensor can be accessed on a ramp or on axle stands. Done it both ways.
2. I do a bracket/sensor kit for the Cerbera but I could adapt it to fit a Chimaera.
3. I use the Racelogic TC setup because I haven't yet seen anything else built into an ECU that gets anywhere near it. There's a challenge for you! It is extremely sophisticated in how it determines what the car is doing and when and when not to come in. It simply cuts injectors. The number of injectors that can be cut is programmable and it distributes the cuts around the cylinder/injectors so that any effect is evened out. It uses several different levels which can be programmed for different levels of wheel slip. You need some wheel slip for optimum grip. To be honest, to control the 500+ bhp I have, the cuts are quite aggressive. If they are not aggressive enough, the system will not respond quickly enough and the TC may cause more problems than it solves.
I have been running it on my Wedge for 10+ years. The last 2-3 with a Vortech blower producing around 540 bhp. The engine was stripped down last week in preparation for a boost increase and again, no problems so the Racelogic system certainly works.
shpub said:
OK....
Lots of answers:
1. Diff sensor can be accessed on a ramp or on axle stands. Done it both ways.
2. I do a bracket/sensor kit for the Cerbera but I could adapt it to fit a Chimaera.
3. I use the Racelogic TC setup because I haven't yet seen anything else built into an ECU that gets anywhere near it. There's a challenge for you! It is extremely sophisticated in how it determines what the car is doing and when and when not to come in. It simply cuts injectors. The number of injectors that can be cut is programmable and it distributes the cuts around the cylinder/injectors so that any effect is evened out. It uses several different levels which can be programmed for different levels of wheel slip. You need some wheel slip for optimum grip. To be honest, to control the 500+ bhp I have, the cuts are quite aggressive. If they are not aggressive enough, the system will not respond quickly enough and the TC may cause more problems than it solves.
I have been running it on my Wedge for 10+ years. The last 2-3 with a Vortech blower producing around 540 bhp. The engine was stripped down last week in preparation for a boost increase and again, no problems so the Racelogic system certainly works.
Steve I am in the process of setting mine up, I had to do some mods to the front brackets, Apart from setting up the wheel counts, channel numbers, wheel size s there anything else that I must set up in the racelogic ?, I guess the number of cuts is set to the default setting at the moment. I also agree this is a much better system as its standalone and having a seperate processor to do this rather than an ECU trying to do everthing. Also like the adjuster in the car whereas an ecu are you going to drive with your laptop connected ??Lots of answers:
1. Diff sensor can be accessed on a ramp or on axle stands. Done it both ways.
2. I do a bracket/sensor kit for the Cerbera but I could adapt it to fit a Chimaera.
3. I use the Racelogic TC setup because I haven't yet seen anything else built into an ECU that gets anywhere near it. There's a challenge for you! It is extremely sophisticated in how it determines what the car is doing and when and when not to come in. It simply cuts injectors. The number of injectors that can be cut is programmable and it distributes the cuts around the cylinder/injectors so that any effect is evened out. It uses several different levels which can be programmed for different levels of wheel slip. You need some wheel slip for optimum grip. To be honest, to control the 500+ bhp I have, the cuts are quite aggressive. If they are not aggressive enough, the system will not respond quickly enough and the TC may cause more problems than it solves.
I have been running it on my Wedge for 10+ years. The last 2-3 with a Vortech blower producing around 540 bhp. The engine was stripped down last week in preparation for a boost increase and again, no problems so the Racelogic system certainly works.
shpub said:
OK....
Lots of answers:
1. Diff sensor can be accessed on a ramp or on axle stands. Done it both ways.
2. I do a bracket/sensor kit for the Cerbera but I could adapt it to fit a Chimaera.
3. I use the Racelogic TC setup because I haven't yet seen anything else built into an ECU that gets anywhere near it. There's a challenge for you! It is extremely sophisticated in how it determines what the car is doing and when and when not to come in. It simply cuts injectors. The number of injectors that can be cut is programmable and it distributes the cuts around the cylinder/injectors so that any effect is evened out. It uses several different levels which can be programmed for different levels of wheel slip. You need some wheel slip for optimum grip. To be honest, to control the 500+ bhp I have, the cuts are quite aggressive. If they are not aggressive enough, the system will not respond quickly enough and the TC may cause more problems than it solves.
I have been running it on my Wedge for 10+ years. The last 2-3 with a Vortech blower producing around 540 bhp. The engine was stripped down last week in preparation for a boost increase and again, no problems so the Racelogic system certainly works.
Hi Steve, I have the 5 stuf hub conversion, does that make a difference?Lots of answers:
1. Diff sensor can be accessed on a ramp or on axle stands. Done it both ways.
2. I do a bracket/sensor kit for the Cerbera but I could adapt it to fit a Chimaera.
3. I use the Racelogic TC setup because I haven't yet seen anything else built into an ECU that gets anywhere near it. There's a challenge for you! It is extremely sophisticated in how it determines what the car is doing and when and when not to come in. It simply cuts injectors. The number of injectors that can be cut is programmable and it distributes the cuts around the cylinder/injectors so that any effect is evened out. It uses several different levels which can be programmed for different levels of wheel slip. You need some wheel slip for optimum grip. To be honest, to control the 500+ bhp I have, the cuts are quite aggressive. If they are not aggressive enough, the system will not respond quickly enough and the TC may cause more problems than it solves.
I have been running it on my Wedge for 10+ years. The last 2-3 with a Vortech blower producing around 540 bhp. The engine was stripped down last week in preparation for a boost increase and again, no problems so the Racelogic system certainly works.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



