Drivers window not working - not door electrical connectors!
Discussion
All,
My drivers side electric window has stopped working (it was a fair few weeks ago it stopped but am just getting round to looking at it)
So, my findings so far are this:
The window mechanism itself is just fine - if a add 12v to the connections behind the speaker I can wind it up and down.
The loom connections in the door are just fine. (and all other door electrics are ok)
The connections to the center console switch are all clean and tidy, however there is no 12v at the switch.
Next thoughts are based round the mass of electricians tape that makes up the loom, and also the connections behind the fuseboard in the back of the footwell, I don't really fancy either much so does anyone have any pearls of wisdoms please before I get into it.
(And before someoene suggests a Fuse: from memory it is a shared fuse so I have ruled that out as everything else in the car electricals works just fine)
Many thanks,
Matt.
My drivers side electric window has stopped working (it was a fair few weeks ago it stopped but am just getting round to looking at it)
So, my findings so far are this:
The window mechanism itself is just fine - if a add 12v to the connections behind the speaker I can wind it up and down.
The loom connections in the door are just fine. (and all other door electrics are ok)
The connections to the center console switch are all clean and tidy, however there is no 12v at the switch.
Next thoughts are based round the mass of electricians tape that makes up the loom, and also the connections behind the fuseboard in the back of the footwell, I don't really fancy either much so does anyone have any pearls of wisdoms please before I get into it.
(And before someoene suggests a Fuse: from memory it is a shared fuse so I have ruled that out as everything else in the car electricals works just fine)
Many thanks,
Matt.
spend said:
If the other window works the fuse will be fine
Strip the tape loom back from the switches and you will see where the +12v is spliced to go to both switches. Your fault will likely be in that short part of loom.
Sounds good, is that within the tape run from both the switch bunches before it goes into the lower dash alongside the top of the passenger footwell? (i.e still under/near the centre console)
Strip the tape loom back from the switches and you will see where the +12v is spliced to go to both switches. Your fault will likely be in that short part of loom.Cheers,
Matt.
M@H said:
spend said:
If the other window works the fuse will be fine
Strip the tape loom back from the switches and you will see where the +12v is spliced to go to both switches. Your fault will likely be in that short part of loom.
Sounds good, is that within the tape run from both the switch bunches before it goes into the lower dash alongside the top of the passenger footwell? (i.e still under/near the centre console)
Strip the tape loom back from the switches and you will see where the +12v is spliced to go to both switches. Your fault will likely be in that short part of loom.Cheers,
Matt.
If there is evidence of copius amounts of insulating tape rather than loom tape (not sticky) somebody has had their dirty hands in there already!

spend said:
M@H said:
spend said:
If the other window works the fuse will be fine
Strip the tape loom back from the switches and you will see where the +12v is spliced to go to both switches. Your fault will likely be in that short part of loom.
Sounds good, is that within the tape run from both the switch bunches before it goes into the lower dash alongside the top of the passenger footwell? (i.e still under/near the centre console)
Strip the tape loom back from the switches and you will see where the +12v is spliced to go to both switches. Your fault will likely be in that short part of loom.Cheers,
Matt.

Thanks, I shall have another look tonight.
M@H said:
spend said:
M@H said:
err, this is TVR we are talking about 
I was talking in schema rather than execution (and hinting at exactly that phenomena) 

my wiring doesn't match any of the ones in the Bible anyway (well the relay layouts don't at least)
owners can go 

...so I was actually getting 12v physically at the switch itself, however as discovered, nothing much after it.
After 2 hours of p!ssing about I have found the Culprit:

note the burn marks on the outer casing where the internals have melted it

it is a full closure module for the alarm system. Hidden well away in the lower dash across from the inertia cutoff switch.. sadly the car now looks like this so I've got some sorting out to do ..aah well.

Matt.
After 2 hours of p!ssing about I have found the Culprit:

note the burn marks on the outer casing where the internals have melted it

it is a full closure module for the alarm system. Hidden well away in the lower dash across from the inertia cutoff switch.. sadly the car now looks like this so I've got some sorting out to do ..aah well.

Matt.
Edited by M@H on Friday 27th February 14:28
Gassing Station | Chimaera | Top of Page | What's New | My Stuff




well worth all that hard work just need some dry weather now.