Off with the heads & CAM questions
Off with the heads & CAM questions
Author
Discussion

mattrosersv

Original Poster:

579 posts

261 months

Wednesday 18th February 2009
quotequote all
Hi,

In the process of changing CAMs on my 70K mile 5.0. While I am OK with a spanner I am now past the limit of anything I have done previously. Have stripped everything back but have now decided to remove heads as well as the car was not running right beforehand (could be a few things like the melted PreCats I found - at least this will save me some time). SO I hope you don't mind but I thought I would lean on the Collective for some help and guidance.

Seeing as it is in bits I thought it would be prudent to have the heads off, while I am at it, to check liners and valves.

Q1: The Haynes manual shows an extra row of head bolts (an additional 4 per side) below the plug hole. My head does not seem to have these bolts so I only have 10 bolts to remove. Am I being really stupid, or do we just have the two rows of head bolts?

Q2: On the top of the heads (In the area under the rocker shaft) are two bolts with a Hex recess (would fit allen key). Do these have to come out?

Q3: Is it prudent to obtain new head bolts on re-assembley?

Q4: To be honest with the heads off I am not entirely sure what I am looking for so any suggestions would be very welcome

Q5: I have my required parts list as follows (This is in addition to the CAM kit):

Head Bolts??
Exhaust Bolts
Exhaust Bolt washers
Sump gasket
Water pump gasket
Heads Gaskets
Exhaust Gaskets

Is it worth replacing anything else while I have it in bits. Valve Guides etc?? Also (and I guess a bit subjective) is it worth getting anything done to the heads while they are off?

Q6 Finally any secrets for cleaning up all the mating surfaces. I never have found a great solution for removing remnents of old gaskets although I do have a can of parafin at hand.

Thanks very much in advance

Barkychoc

7,848 posts

235 months

Wednesday 18th February 2009
quotequote all
mattrosersv said:
In the process of changing CAMs on my 70K mile 5.0. While I am OK with a spanner I am now past the limit of anything I have done previously. Have stripped everything back but have now decided to remove heads as well as the car was not running right beforehand (could be a few things like the melted PreCats I found - at least this will save me some time). SO I hope you don't mind but I thought I would lean on the Collective for some help and guidance.

Seeing as it is in bits I thought it would be prudent to have the heads off, while I am at it, to check liners and valves.

Q1: The Haynes manual shows an extra row of head bolts (an additional 4 per side) below the plug hole. My head does not seem to have these bolts so I only have 10 bolts to remove. Am I being really stupid, or do we just have the two rows of head bolts?
You are right, later models don't have those 4 bolts.

mattrosersv said:
Q2: On the top of the heads (In the area under the rocker shaft) are two bolts with a Hex recess (would fit allen key). Do these have to come out?
No need to touch those

mattrosersv said:
Q3: Is it prudent to obtain new head bolts on re-assembley?
With 10 bolt heads it is essential as they are stretch bolts and cannot be reused. There is lots of debate whether to replace with stretch bolts or standard ones. Standard for me.

mattrosersv said:
Q4: To be honest with the heads off I am not entirely sure what I am looking for so any suggestions would be very welcome
You are worrying me now - be careful

mattrosersv said:
Q5: I have my required parts list as follows (This is in addition to the CAM kit):

Head Bolts
Exhaust Bolts
Exhaust Bolt washers
Sump gasket
Water pump gasket
Heads Gaskets
Exhaust Gaskets
If you are stripping the engine you will get better value buying gasket sets. Get them from a respected Indie not ebay

mattrosersv said:
Is it worth replacing anything else while I have it in bits. Valve Guides etc?? Also (and I guess a bit subjective) is it worth getting anything done to the heads while they are off?
Strip & decoke the heads and see where you go from there.
Post pics on here and you'll get plenty of armchair mechanics advice!
Probably better to take them to an engineering shop if you have the budget.

mattrosersv said:
Q6 Finally any secrets for cleaning up all the mating surfaces. I never have found a great solution for removing remnants of old gaskets although I do have a can of parafin at hand.
Take your time and do not use a metal scraper on alloy components. I'm sure there will be some more good suggestions about this.
Personally I would not be in a hurry to take the heads off - I'd take the cam out first and see what that shows.
I have a non cat car but I'm guessing the pre cats could have collapsed and caused a blockage leading to excessive heat build up and poor running.
Better to get the pre cats out anywaybiggrin

mattrosersv

Original Poster:

579 posts

261 months

Wednesday 18th February 2009
quotequote all
Thanks for the response. I am now off to garage to get the head off. Sorry forgot to mention CAM is out already.

Two of the Exhaust lobes were worn but not excessive (compared to a friends which ran fine if a little slow) Pretty sure this is not the reason for rough running. Mechanic friend of mine suggested I would be an idiot for not taking the heads off at this point.

My thoughts are at least I can rule valves / head gasket out the reason for lumpy running. This occured after I had the exhaust manifolds glowing due to very poor running due to coil failure so could well be the precat remains that caused the lumpy runnig. Was also a bit concerned about Precat debris damaging exhaust valves.

I want to make sure when it is back together I have ruled out as many caused as possible. Don't want to get into the poor running reason until it is back together.


Chimjunkie

2,879 posts

242 months

Wednesday 18th February 2009
quotequote all
A lot of information about the valves can be obtained by a simple compression test. If the valves are not seating correctly then the compression will be low. Setting the cam timing is the most difficult job. This requires great care and absolute confidence that you know what you are doing! You will also need a timing wheel, two DTI gauges and various bit of metal to make brackets to hold said DTI gauges. Not for the faint hearted. I would rate this as borderline DIY/proffesional as a job. The next worst job is setting the valve preload. If you dont know what this means then tread carefully with your strip down!

Good luck.




clive f

7,259 posts

264 months

Wednesday 18th February 2009
quotequote all
you can run a straight edge across the tops of your valves, and make sure that they are all the same hieght, some may stick up more than others, normally exhaust valves, as they wear into the seating more, if so remove the heads and get them re seated, by if your head gaskets are not blown, and plugs are all the same colour, and its not buring loads of oil, I wouldn`t bother, but if you have the time and the money then give it a go.

have a chat with Spend on here, he has done a lot of porting work on his heads and may give you some very useful advice.yes

alos its worth checking out the rpi engineering website, they have some very usefull "how to", sections checking the pre load is well covered in there as well.

Edited by clive f on Wednesday 18th February 20:06

mattrosersv

Original Poster:

579 posts

261 months

Wednesday 18th February 2009
quotequote all
Thanks again, I have said gauges and have read up on the V8 D web site, all looks pretty straight forward to be honest.... Also have a mate up the road who did this 6 months ago with no problem who will assist.

With regard to Pre-Load I have the adjustable pushrods so I guess this negates this step?? Although I obviously need to set up each push rod. Again all looks pretty straight forward.

Can't see taking the heads off is too laborious or expensive (2 head gaskets + bolts) given where I am with the strip down. It will be worth the few hours work for piece of mind and will also allow me to clean up the inlet ports properly which got some grime in them from the trumpet base removal.

If anything looks like it is not as it should be it will go straight to a professional.








Chimjunkie

2,879 posts

242 months

Wednesday 18th February 2009
quotequote all
Very rewarding as a personal achievement. Did this work on mine a short while ago due to snapped timing chain. Enjoyed it except for the freezing weather frown

spend

12,581 posts

282 months

Thursday 19th February 2009
quotequote all
You will need an inlet valley gasket + seals and a timing (aka oil aka front) cover gasket. V8D do rather nice sets with thinner comp gaskets to give you a teeny bit more compression.

Robs great for cams, since you already have adjustable rods it would seem rude not to have a solid cam IMHO wink I never realized until today that lots of your BV heads have humongous valve guides, certainly worth asking for them to be sorted whatever you do.

Just make sure you take your time and match the inlet & exhaust ports to the manifolds as best you can, and don't leave gaskets blocking the ports either.

mattrosersv

Original Poster:

579 posts

261 months

Thursday 19th February 2009
quotequote all
Thanks for the heads up on Valve Guides Spend,

I already have V8D Stealth, Valley and Timing gaskets and will be back in touch with them for the rest of the requirements.

spend

12,581 posts

282 months

Thursday 19th February 2009
quotequote all
Forgot last night but if you have heads off make sure the push rod holes are enlarged. Many drill them out, but I prefer to run a burr down them and elongate (the push rods mainly sway in the direction of the rockers rather than side-side). I would do it even for standard pushrods, but with adjustable rods its really necessary IMHO - check your pushrods for scoring.

I do like to take the rough casting edges of the heads inside & outside as well, mainly cos its not hard to do & makes me feel good hehe Some folks do it for oil flow, but I just think of it as stress relief against cracking (for me as well as the engine rofl)


That Daddy

19,464 posts

252 months

Thursday 19th February 2009
quotequote all
spend said:
Forgot last night but if you have heads off make sure the push rod holes are enlarged. Many drill them out, but I prefer to run a burr down them and elongate (the push rods mainly sway in the direction of the rockers rather than side-side). I would do it even for standard pushrods, but with adjustable rods its really necessary IMHO - check your pushrods for scoring.

I do like to take the rough casting edges of the heads inside & outside as well, mainly cos its not hard to do & makes me feel good hehe Some folks do it for oil flow, but I just think of it as stress relief against cracking (for me as well as the engine rofl)
yes Aint nothing wrong with removing casting flash

rev-erend

21,624 posts

315 months

Thursday 19th February 2009
quotequote all
Some very good info here on about heads, cam and cam set-up

http://www.g33.co.uk/tuning.htm


mattrosersv

Original Poster:

579 posts

261 months

Wednesday 25th March 2009
quotequote all
Hi All,

Just thought I would post a final report.

I changed the CAM for a V8D Stealth. The original cam was worn, but not nearly as bad as others I have seen.

I was pretty confident that I had the timing back exactly as it came out and it ran exactly as when I took it apart.

Got the strobe on it and it was FAR too advanced. Set it up correctly and it runs sweet as a nut.

If I had to guess what happened here I reckon the coil failed causing the original breakdown (glowing manifolds) the dodgy garage then fitted new plugs (ste one, 1 x cracked, 2 x loose) fitted new leads (ste, connectors fell off when disconneting from dizzy) before I told them to replace the coil which fixed it. Perhaps they messed with the timing causing the bad running...... I am not certain with this, the bad running could have been caused by the burnt out pre-cats/blocked main cat, but seems strange the symptoms where identical.

In replacing the CAM I found my precats had burned out so removed the rest. The inlet gasket was definitely on the way out, really rusty and looked like the water inlets were starting to seep.

I have a massive sense of achievement as this is a major step on from any spanner throwing I have done before. Not much I wouldn't attempt now.

Thank you very much to all who contributed on this thread and the many other threads I read to get me to this point.

I'm off for a drive now!

Matt

Chimjunkie

2,879 posts

242 months

Wednesday 25th March 2009
quotequote all
Well done!! Enjoy that Stealth cam too smile

Teetertank

358 posts

218 months

Thursday 26th March 2009
quotequote all
Well done on getting everything sorted.

mattrosersv said:
In replacing the CAM I found my precats had burned out so removed the rest.
Are there any definitive symptoms to tell if the precats have melted or got blocked (without taking the manifolds off)?

I remember looking under the bonnet one dark night to check for HT lead arcing, after I had been driving the Chim, and saw that the exhaust manifolds (on both sides) were glowing red hot in the area where the precats are located. This is making me question their condition. But maybe glowing headers are normal???

mattrosersv

Original Poster:

579 posts

261 months

Thursday 26th March 2009
quotequote all
Can't really advise with the symptoms as I **think** the poor running was due to the ignition timing being out, but I don't know this for sure.

What I do know is that they only glowed when there was something else wrong. This has happened twice, once when the car broke down at the start of all this. I think that was due to me driving the car about 1/2 mile with a really bad misfire which I think was due to coil failure. the precats were glowing bright orange!

There must have been a load of unburnt fuel going into the precats and they burned themselves out leaving some large chunks floating around the Y piece.

The second time they glowed (well actually the main CAT glowed since I have no Precats) was yesterday when I fired it up for the first time after putting it back together with timing that turned out to be WAY too advanced. This was casuing the engine to misfire badly.

Do you have any symptoms on anything else being wrong. Hopefully someone more knowledgeable than me will be able to help.

Teetertank

358 posts

218 months

Thursday 26th March 2009
quotequote all
No other symptoms, but have since replaced the vernier timing sprocket which had slipped round causing poor running.

Haven't checked the manifolds in the dark since, but will do at next opportunity.

blitzracing

6,422 posts

251 months

Thursday 26th March 2009
quotequote all
On removing old gaskets, use paint stripper and let it soak. Works well.