Fitting ACT Silicon Cooling Hose Kit
Fitting ACT Silicon Cooling Hose Kit
Author
Discussion

sgrimshaw

Original Poster:

7,587 posts

281 months

Wednesday 18th February 2009
quotequote all
Anyone have any experience of fitting ACT's Silicon Hose kit to a Serpentine Chimaera 400?

Is it a straightforward job, any real bhes to do?

It something I'd probably get my service guy to do, but I don't want to give him a job that takes all day because of a couple really hard to get at ones.

Thanks in advance.

Simon

glow worm

7,525 posts

258 months

Wednesday 18th February 2009
quotequote all
Very easy really...even I've managed to do it twice , on different cars. Quite rewarding to do it yourself. Just make sure you plan which hose goes where, some are 35mm ,some 38mm and one 38mm one end and 35 the other. Instructions are good. Take off your swirl tank and give it a polish at the same time. Also I've always replaced the swan neck with a stainless steel one...the TVR ones are mild steel and rust. Make sure heater turned on when you disconnect pipes, when complete refil from the swirl tank. Then run engine with swirl tank cap off (and blue cap off), wait until it bubbles are the air gets blown out, keep topping up. Switch off...leave to brew....check again and top up if necessary...add to the expansion tank to your usual level ...and job done... probably have a few leaks, but just nip up jubilee clips.And don't forget to fill with anti-freeze.
PS Usually finish up cutting the small bore heater hoses to get them off.

PPS Check your radiator bottom hose outlet... Standard ones are right angled...so Tim normally sends a right angled hose...but my first Chim had a rad with a straight outlet and needed an 'S' shaped hose..which Tim sorted once he knew.

Edited by glow worm on Wednesday 18th February 16:48


Edited by glow worm on Wednesday 18th February 22:45

sgrimshaw

Original Poster:

7,587 posts

281 months

Wednesday 18th February 2009
quotequote all
Hi Glow Worm,

Thanks for the reply.

Understood most of it, apart from "swan neck" - which bits that?

glow worm

7,525 posts

258 months

Wednesday 18th February 2009
quotequote all
There's a metal pipe that joins to your bottom radiator hose, as it goes over your front axle/steering. It was a small bore pipe for your heater and the large other end goes to the bottom of your engine.
You can just see it on the photo above the exhaust manifold (exteme bottom right hand side)...Shinning!!
(PS I'll get even more stick for posting another photo)



But besides play golf...what else is there to do when you retire.... but polish!!! and drive.




Edited by glow worm on Wednesday 18th February 17:34

big geoff

387 posts

231 months

Wednesday 18th February 2009
quotequote all
can you tell me what you have fitted to or on the fuel pipes in the picture please

glow worm

7,525 posts

258 months

Wednesday 18th February 2009
quotequote all
Good point..that was on the car when i bought it last year...I assume from new since a 2001 car...I guess its fitted as insulation to keep the heat away from the fuel lines. I'll enquire from my factory man if it was standard on later models...does seem a good idea.

Update... Apparantly it's called NOMEX made by DuPont http://www2.dupont.com/Nomex/en_US/ ... as usual it was a TVR flavour of the month...someone thought it was a good idea...lasted for a few months until it ran out, then never appeared on a car again... it is quite expensive (I understand) so that might also be the reason.

Edited by glow worm on Thursday 19th February 16:24

S4CJO

429 posts

290 months

Wednesday 18th February 2009
quotequote all
Fitted the same set two years ago as shown in Glo Worms picce before going to Le Mans and touring South France and no problem. Only issue was the pipe to the header tank which I think Tim said at the time was the wrong one he then sent out the correct one that day. Also fitted the stainless bottom pipe instead of the old steel one which attracted all the dross the road could throw at it.

Just do it............bow

sgrimshaw

Original Poster:

7,587 posts

281 months

Thursday 19th February 2009
quotequote all
OK I can see the "swan neck" that GW described.

Where do I get a SS one?

sgrimshaw

Original Poster:

7,587 posts

281 months

Thursday 19th February 2009
quotequote all
Are these the SS pipe described above?

http://www.actproducts.co.uk/shop/index.php?main_p...

Thanks

glow worm

7,525 posts

258 months

Thursday 19th February 2009
quotequote all
Yep, a SC006A should be the one on a '99 Chim, don't forget to check your bottom outlet on your radiator (mine 1st one was a '99 T reg that had a straight outlet).

That Daddy

19,464 posts

252 months

Thursday 19th February 2009
quotequote all
glow worm said:
There's a metal pipe that joins to your bottom radiator hose, as it goes over your front axle/steering. It was a small bore pipe for your heater and the large other end goes to the bottom of your engine.
You can just see it on the photo above the exhaust manifold (exteme bottom right hand side)...Shinning!!
(PS I'll get even more stick for posting another photo)



But besides play golf...what else is there to do when you retire.... but polish!!! and drive.




Edited by glow worm on Wednesday 18th February 17:34
Why would you get stick? that under bonnet pic looks crap heheredcard

Edited by That Daddy on Thursday 19th February 10:24