Bleeding brakes after strip down
Discussion
How do I purge the brake system of air following a complete strip down (Chim 450)? No amount of pedal pumping seems to get the air through, nor does the use of a pressure bleed tool (where you use the spare tyre to pressurise a cannister full of fluid that then connects to the master cylinder).
Is there a simple trick to sorting the problem?
Is there a simple trick to sorting the problem?
If it's been completely drained you need to look for all the spots where air can get trapped, and chase the air out of it. Best to start from the master cylinder and work outwards towards the callipers. For example to bleed the m/c you may need to unmount if and turn it over so that the outlet pipes are at the top. Similarly some callipers need to be turned over to chase the air through to the bleed nipple.
I dont know if the Tiv is the same as the Ginetta (this uses Ford cosworth brake parts), but the rear calipers have to be removed and held horizontally to get the air out. I only found out after I had replaced both master cylinders (twice) and the reservior and spent many hours swearing at it. Also be aware that some of the bleed tubes you use, can let air back in via the nipple thread so dont bleed fully. If you can get ANY pressure in the system, your best bet is to pump the pedal up, and then get someone else to loosen the bleed nipple to let the air out as the pedal drops, and then tighten the nipple before you lift the pedal back up. Then repeat the process. If you put a clear tube over the nipple you should see as fresh fluid comes through, so you can see once its bubble free. Garages have a vacume system that sucks the fluid through, pulling the air out as it goes.
You need to do it sequence, o/s F, n/s F, o/s R, n/s R. Make sure all the bleed valves are shut. Don't let the eazibleed (whatever) run dry, I found mine seemed to work better with very low (<10) psi to start with (compressor next to car, tyre outside garage!) It also seemed to work better by opening and closing the bleed valve rather than just leaving it open.
spend said:
You need to do it sequence, o/s F, n/s F, o/s R, n/s R. Make sure all the bleed valves are shut. Don't let the eazibleed (whatever) run dry, I found mine seemed to work better with very low (<10) psi to start with (compressor next to car, tyre outside garage!) It also seemed to work better by opening and closing the bleed valve rather than just leaving it open.
i thought i did mine furthest 1st...
Its a lot trickier when you've drained the whole lot... Much better to clamp & do a corner at a time then bleed before starting the next corner I reckon. That's not feasible when you have all 4 corners off though and the way I quoted worked to reprime my system, then I went through normal bleeding a couple of times...The title is misleading though and I think of this as getting the system primed and different from conventional periodic bleeding?
Never had to do it on a car but found a good way to prime a motorbike system is to back feed from the caliper with a tube and a large syringe (use these at work to draw oil samples out of filler necks on the diesel loco's)cant see why it wouldnt work on a tiv...otherwise as said,clamp flexi pipes on those not being bled and rotate until all filled,then bleed furthest away from master cylinder to closest...
spend said:
Its a lot trickier when you've drained the whole lot... Much better to clamp & do a corner at a time then bleed before starting the next corner I reckon. That's not feasible when you have all 4 corners off though and the way I quoted worked to reprime my system, then I went through normal bleeding a couple of times...The title is misleading though and I think of this as getting the system primed and different from conventional periodic bleeding?

... but we know you're faster than everyone else Beachy 
Guess its how much / where there is some resistance otherwise the air just compresses? Filling in the shortest routes first worked for me, when doing it normally was not working. It may have been Neill A. who warned me to do the fronts first with the AP brakes, can't really remember but certainly a tip from a TIVver
Just told do shortest first so you get some air expelled gradually. I did actually drain & clean my res whilst at it to boot (you know me filthy outside & clean where nobody sees - closet cleaner or what?
)

Guess its how much / where there is some resistance otherwise the air just compresses? Filling in the shortest routes first worked for me, when doing it normally was not working. It may have been Neill A. who warned me to do the fronts first with the AP brakes, can't really remember but certainly a tip from a TIVver
Just told do shortest first so you get some air expelled gradually. I did actually drain & clean my res whilst at it to boot (you know me filthy outside & clean where nobody sees - closet cleaner or what?
)Gassing Station | Chimaera | Top of Page | What's New | My Stuff






