Anyone using exhaust wrap?
Discussion
I have done the precat area to stop the ringing after they were removed.
One thing I learnt was there is exhaust wrap and there is exhaust wrap. The cheaper white stuff looked pretty naff and was falling to bits after a few days. Got a big reel of the carbon impregnated kind of ebay which looked alot better and seemed tougher. Used some SS lock wire with those twist pilers to hold it on.
As the car is in a dehumidified garage I am not too worried about rust.
One thing I learnt was there is exhaust wrap and there is exhaust wrap. The cheaper white stuff looked pretty naff and was falling to bits after a few days. Got a big reel of the carbon impregnated kind of ebay which looked alot better and seemed tougher. Used some SS lock wire with those twist pilers to hold it on.
As the car is in a dehumidified garage I am not too worried about rust.
hi, i have the pre cats,y peice and main cats wrapped , the under bonnet temps have dropped , just hope it does not cook the main cat !got the steal tie`s from flea bay extra long and went for the 2" wrap , you will need more than you think .
Edited by daz the plumber on Saturday 21st February 19:24
50' of 2" wrap is ample to do both sides plus the Y piece. I had mine done for years. It makes it a bit quieter, and the engine bay was noticeably cooler and component failures under the bonnet were much less of a problem afterwards. I didn't notice any particular problem with corrosion, but I did find the #1 and #2 headers cracked and needed to be welded up a couple of times over the years. This isn't uncommon even on a standard unwrapped exhaust though. You can get special stainless steel ratchet straps to hold the wrapping on. They're quite expensive and you don't strictly need them. Better to get yourself a roll of stainless lockwire, then secure the bandage every few inches. It is quite fragile stuff and will start to crack and fall off after a couple of years, but if you have it secured every few inches you will only lose small pieces rather than have the whole thing fall off.
Be prepared for it to produce *lots* of smoke the first time it gets really hot after you have fitted it. I thought the engine was on fire.
Be prepared for it to produce *lots* of smoke the first time it gets really hot after you have fitted it. I thought the engine was on fire.

daz the plumber said:
just hope it does not cook the main cat
Only wrap just passed the precats. Not a good idea to wrap the main cat. This will run too hot.Had mine wrapped for a few years but now replacing with a set of CliveF's old Cam-coated manifolds. Both my manifolds leaked where the 4 tubes go into one. Again, dont know if this had anything to do with being wrapped. No noticeable difference in surface rust. But you must use the car regularly. Any trapped moisture then vapourises.
Moisten the wrap in water before you start to wrap the exhaust,keeps the fibers frrom seperating and getting in all the wrong places,very itchy stuff..... DEI wrap is good stuff,did my impreza manifolds and system 3 years ago and still in good nick,the extra heat kept in by the wrapping can cause crackes to develop,but this can happen naturally on these cars so not much to worrry about there.....
daz the plumber said:
what i did was spray carpet adesive on the manifolds, then wrap as normal but it makes the job very easy . i then started her up and let the heat burn it away .i was a little worried but it worked !
I guess you only did this to help fit the bandage in the first place, but it will be interesting to find whether the adhesive continues to stick the bandage to the exhaust. If it does, I think you could find the bandage lasts a lot longer than when it's just 'dry' wrapped.There is no need for an adheasive once its fitted! Once applied the wrap will spoke like a bugger for the first 45 mins of being hot. It will then go semi-stiff and not budge if you wraped it right. The way we do it on the Formula Renaults and F3s is to wrap with it DRY. When you wet the tape (as in the instructions) the tape shrinks and leaves the job loose, but it wont be so itchy if that helps. So wrap dry, and dont use metal tie wraps, use tight lockwire every 3" and just one tie when you wrap. Remember a good job must be consistent allong its lenth. Many people on here seem to think the heat cracks the pipes; Not so! The heat increace has no effect here, inface the incresed cooling time makes cracking less likely. The problems come when you do a poor job and some bits cool down faster than others. Good luck!
stevejdurrant said:
Many people on here seem to think the heat cracks the pipes; Not so! The heat increace has no effect here, inface the incresed cooling time makes cracking less likely.
There seems to be speculation presented as fact there. There seems to be a fairly common experience of cracking after applying heat wrap. It's entirely possible for the increased heat to cause increased thermal expansion resulting in stress cracks. Your assertion that it doesn't happen or isn't caused by the bandage seems rather tenuous.Gassing Station | Chimaera | Top of Page | What's New | My Stuff






