Valve stem seals - easy enough?
Valve stem seals - easy enough?
Author
Discussion

VerySideways

Original Poster:

10,272 posts

303 months

Sunday 22nd February 2009
quotequote all
I think my left hand bank has a bit of an oil consumption problem and i'm 90% sure it's not rings so i'm guessing it's valve stem seals.

Since this is a pretty simple 16 valve, single cam, pushrod engine i'm guessing that changing the valve stem seals should be a doddle, right?

Pop the plenum out the way, undo the plug leads, pop the rocker cover off, take the rocker arm off, and then get the old valve spring compressor out and get to work right?

Last time i did this was an ex-girlriends OHV Fiesta, same thing right?

Or am i over simplifying? biggrin

VerySideways

Original Poster:

10,272 posts

303 months

Sunday 22nd February 2009
quotequote all

spend

12,581 posts

282 months

Sunday 22nd February 2009
quotequote all
I think the biggest dilemma is that when you get the springs off, you won't like the look of the gouging in the spring seats. Unless you are really in a rush, popping the heads off so you can clean, lap .. have the spring seats reground and steel shims put in.. is the way I would approach it. I reckon its the price you have to pay with the cams & uprated valve springs?

VerySideways

Original Poster:

10,272 posts

303 months

Sunday 22nd February 2009
quotequote all
Well, having look at that other thread i think what i'll do is go and compression test the engine.
If it's even across all the cylinders then i'll just replace the valve stem seals for now and see how i get on, i can always take the heads off next winter.
If the compression is crap then i'll have to decide if i should fix it myself or just give it to someone else to do (which will be quicker and save me taking time off work).

spend

12,581 posts

282 months

Sunday 22nd February 2009
quotequote all
Not a great picture (and its not all swarf) but should give you an idea of the wear to expect on the spring seats. These were not bad ones either from what I've seen?

http://foo.dspen.com/springseat.jpg

That Daddy

19,464 posts

252 months

Sunday 22nd February 2009
quotequote all
Shame they didn't fit those nice thin steel shims that most other manufacturers alloy cylinder heads seem to be fitted with,didn't even know spring seat recession could be a problem on the RV8 frown

GreenV8S

31,027 posts

315 months

Sunday 22nd February 2009
quotequote all
VerySideways said:
Pop the plenum out the way, undo the plug leads, pop the rocker cover off, take the rocker arm off, and then get the old valve spring compressor out and get to work right?
Pretty much, assuming you have a valve spring compressor that can compress the spring in situ. Obviously you'll need something to hold the valve up, I use the 'rope' trick but others use an air line into the plug hole. Access to the back of the engine is going to be a bit awkward because the bodywork comes so far forward, but apart from that it's straight forward.

VerySideways

Original Poster:

10,272 posts

303 months

Tuesday 24th February 2009
quotequote all
Anyone have the torque settings to hand for the rocker arm assembly and the rocker covers?

All the stuff on the internet seems to point to between 25 and 35 lbft.

Edited by VerySideways on Tuesday 24th February 10:01

WOO5IE

967 posts

228 months

Tuesday 24th February 2009
quotequote all
Try using this link

http://landrover-online.dk/L-R%20WSM/engine/V8over...

or the v8developements web site

Trev

VerySideways

Original Poster:

10,272 posts

303 months

Tuesday 24th February 2009
quotequote all
Nice one, thanks :-)

Pupp

13,038 posts

303 months

Tuesday 24th February 2009
quotequote all
Never had any issue with the spring seats on mine; I'm wondering if that's more of an issue if the springs are very tired and perhaps moving around at higher rpm.

Access to the rear ones is very tight, in fact it's marginal and a right faff (but do-able). Thing that caused me most concern was on rebuilding/restarting, I had quite a lot of valve noise and the wisdom of those I asked seemed to be along the lines the lifters had probably over-pumped. Given they are not easily (if at all) bled down in situ, and I was looking at a potential strip down anyway, I just took it out and caned it... all quiet again. Probably not the approved method hehe

DavidLScott

1,048 posts

255 months

Tuesday 24th February 2009
quotequote all
Had my stem seals done last year as the car was smoking like mad for a short while after starting from a 2 week or so lack of use.

I am no mechanic so got Fernies to do the whole thing and they reground the valves and had the chance to give both heads a good look over after 60k miles - no further problems and IIRC the whole thing including the service was around £1500.

spend

12,581 posts

282 months

Tuesday 24th February 2009
quotequote all
I would have thought its more likely to be down to the cam profile & rev ranges.. the TVR dual springs seem pretty durable from what I've measured (certainly compared to the mishmash you get with std Rover springs - yes I've stripped a few for bits and compared out of purile interest hehe).

VerySideways

Original Poster:

10,272 posts

303 months

Friday 27th February 2009
quotequote all
Well, did the left hand bank - couldn't get the air adapter thingy on to the back two plug holes very well which made it nerve wracking but apart from that it was good.
Plug on cylinder 3 (second one from the front on the left hand bank) was absolutely caked, and one of the valve stem seals on that cylinder was oval. OVAL!
New plug, new valve stem seals, car runs like a dream biggrin

Thanks for everyone's help on this thread, i will get some nylon rope before i do the other bank, just in case.

Pupp

13,038 posts

303 months

Friday 27th February 2009
quotequote all
Well done for getting in there... no biggie if it goes wrong, just take the head off smile