Still stalling help needed!!!!!!!
Discussion
Ive picked up a intermediate stalling problem
-
As soon as i clutch it down theres no lurch it just dies... unless i catch it early enough.
Ive checked for air leaks, removed and re sealed the plenum. Removed, cleaned and sealed both the stepper and housing, checked and tightened all hoses, ive also tried adjusting the idle screw on the plenum but it made no difference unless i closed it.
Ive re set the ecu, cleaned temp sensor connections, checked both the throttle pot and AFM voltages
The car runs sweet when its not playing up, it idles at 900rpm with no spikes and very little shunting .
Would a faulty temp sensor or hot start cause this?
Any ideas what to check or try next?
-As soon as i clutch it down theres no lurch it just dies... unless i catch it early enough.
Ive checked for air leaks, removed and re sealed the plenum. Removed, cleaned and sealed both the stepper and housing, checked and tightened all hoses, ive also tried adjusting the idle screw on the plenum but it made no difference unless i closed it.
Ive re set the ecu, cleaned temp sensor connections, checked both the throttle pot and AFM voltages
The car runs sweet when its not playing up, it idles at 900rpm with no spikes and very little shunting .
Would a faulty temp sensor or hot start cause this?
Any ideas what to check or try next?
BBR said:
Faulty connection at 100 amp fuse? Battery state connections? Also how old is the fuel and is it 98 or 95 RON?
Hi The batterys a year old, its a new 100amp fuse but i will check this again.
there could be a little old fuel in the tank maybe £5`s worth mixed with approx £30 of 98 RON.... but that wouldnt make the symptoms im getting would it? Edited by Meatball on Sunday 1st March 15:40
Did you manage to clean the stepper properly ?- I dont remember. Try disconnecting the stepper when its ticking over nicely, and then see if it still stalls when you drive it.
Servicing the stepper motor.
I have now perfected a way of getting them to bits to clean, without damage:
1) Get the car warm
2) Remove the stepper from the plenum and reconnect it.
3) Hold the stepper in your hand, so you can catch the central cone and spring when it comes out.
4) Get someone to start the car. Without the stepper in place it will rev at around 2k- 2.5k (This is noisey!!), but the ECU will try to slow it down by powering the stepper motor and pushing cone outwards. It will do this in a series of pulses, a few seconds apart, until the cone and spring drop out. (assuming they are not completely stuck). It may take a bit of manual help to get the cone to fully release. Now stop the engine and let it cool.
6) Clean all the muck of the shaft, and lightly lubricate the screw thread inside the motor.
7) To reassemble, wind the shaft back into the motor so far, but align the slot in the shaft with the plastic keyway as best you can by rotating the shaft in its screw thread
8)With the engine cool, then reconnect the stepper motor. Power cycle the ignition on and off, (don't start) and the ECU will try to pull the shaft back in each time the ignition is turned OFF. This is the slightly tricky bit, as if the keyway and shaft are not quite aligned it wont pull home, so you may need a few attempts.
Mark
Servicing the stepper motor.
I have now perfected a way of getting them to bits to clean, without damage:
1) Get the car warm
2) Remove the stepper from the plenum and reconnect it.
3) Hold the stepper in your hand, so you can catch the central cone and spring when it comes out.
4) Get someone to start the car. Without the stepper in place it will rev at around 2k- 2.5k (This is noisey!!), but the ECU will try to slow it down by powering the stepper motor and pushing cone outwards. It will do this in a series of pulses, a few seconds apart, until the cone and spring drop out. (assuming they are not completely stuck). It may take a bit of manual help to get the cone to fully release. Now stop the engine and let it cool.
6) Clean all the muck of the shaft, and lightly lubricate the screw thread inside the motor.
7) To reassemble, wind the shaft back into the motor so far, but align the slot in the shaft with the plastic keyway as best you can by rotating the shaft in its screw thread
8)With the engine cool, then reconnect the stepper motor. Power cycle the ignition on and off, (don't start) and the ECU will try to pull the shaft back in each time the ignition is turned OFF. This is the slightly tricky bit, as if the keyway and shaft are not quite aligned it wont pull home, so you may need a few attempts.
Mark
I had a similar problem, car would start but you couldnt rev it, then it would cut out.
I removed and cleaned the stepper motor and the throttle butterfly, then most important, reset the base idle speed by squashing the air bypass hose flat to prevent air getting through to the stepper motor and adjusting the throttle screw to idle about 400-500rpm. When you release the hose, it should idle about 900rpm, it may need slight adjustment.
This worked for me and I have had no trouble since.
Good luck..
I removed and cleaned the stepper motor and the throttle butterfly, then most important, reset the base idle speed by squashing the air bypass hose flat to prevent air getting through to the stepper motor and adjusting the throttle screw to idle about 400-500rpm. When you release the hose, it should idle about 900rpm, it may need slight adjustment.
This worked for me and I have had no trouble since.
Good luck..
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


