ACT Induction kit
ACT Induction kit
Author
Discussion

lewis_sharman

Original Poster:

5,958 posts

222 months

Monday 2nd March 2009
quotequote all
Got the car booked up for a dyno run on 23rd of this month (mainly to check to see how it is doing after 100,000 miles), so i thought it would be a good idea to do a full 12,000 mile service on it myself to make sure everything is tip top.

This is where my *money saving* stupidity has come in.

Somehow, while looking for replacement air filters i have managed to worm myself onto the ACT website and order a full smooth bore induction kit from them.

I am so weak frownrolleyes

Is there anything else i should be checking?

Hoover.

5,993 posts

273 months

Tuesday 3rd March 2009
quotequote all
at that kind of mileage (the car looks fantastic by the way)... I'd consider over anda bove the service book requirements at looking at getting the injectors cleaned/replaced.... check the cam for wear as well..... but evrything else should be fine provided serviced regulary... airfilter is generaly the biggest over looked though due to access requirements

debaron

878 posts

228 months

Tuesday 3rd March 2009
quotequote all
Don't beat yourself up over that ACT kit - it's worth about an extra 10 BHP, especially with the smooth right angle pipe - You bought well!

If it was me, I'd have thrown the ACT carbon fibre trumpet set in the basket while I was there too! wink



I'd take a look at Oil filer, Fuel filter (tough job), Air filter, brake pads and fluids (PAS, Hydraulic etc)

Chimjunkie

2,879 posts

242 months

Tuesday 3rd March 2009
quotequote all
Dont check the engine badge! You may be too weak and buy a 500 wink

Oil levels in rear diff and gearbox
Change Fuel filter
Oil/plugs/check leads for damage


If you do a search there is a comprehensive list somewhere.

Which garage is dynoing it?


daz the plumber

14,997 posts

262 months

Tuesday 3rd March 2009
quotequote all
tell them you want discount , beleive me it works !got my carbon trumpets £100 cheaper

GreenV8S

31,027 posts

315 months

Tuesday 3rd March 2009
quotequote all
lewis_sharman said:
Got the car booked up for a dyno run on 23rd of this month (mainly to check to see how it is doing after 100,000 miles)
Full power dyno runs can be rather hard on the engine, are you sure that it's (a) going to tell you anything useful and (b) something you really want to be putting a tired engine through?

kenny Chim 4

1,604 posts

289 months

Tuesday 3rd March 2009
quotequote all
lewis_sharman said:
Is there anything else i should be checking?
I bought my car with the ACT induction kit already fitted. Unsure if it's supplied, therefore, but my rubber intake has a heat-proof sleeve wrapped around it where the intake meets the nearside manifold.

lewis_sharman

Original Poster:

5,958 posts

222 months

Tuesday 3rd March 2009
quotequote all
Thanks for all the info, i was planning on going through all fluids and filters along with brakes aswell, but had neglected to think of the injectors. Is there anywhere around the south east that anyone would recommend for cleaning?

And i have full confidence in the fact that its still in good health in the time that i have had it.

Worst case scenario = Good excuse to get a 4.6 wink

ph1l5

5,027 posts

233 months

Tuesday 3rd March 2009
quotequote all
Thats weird I just had my car on the Dyno on Saturday and have now ordered the same ACT smooth induction pipe kit too.

lewis_sharman

Original Poster:

5,958 posts

222 months

Tuesday 3rd March 2009
quotequote all
ph1l5 said:
Thats weird I just had my car on the Dyno on Saturday and have now ordered the same ACT smooth induction pipe kit too.
thumbup Hopefully it will make a noticable difference.

What was your car making on the rollers out of interest?

ph1l5

5,027 posts

233 months

Tuesday 3rd March 2009
quotequote all
215 bhp and 244 Lb torque so was a little dissapointed but have been told that, that is right for a 17 year old car with no mods. So now I am about to start getting some bits to make it go a bit better.

lewis_sharman

Original Poster:

5,958 posts

222 months

Tuesday 3rd March 2009
quotequote all
That seems about right from what ive heard. I will post up my results as well once its done.

chim

245 posts

228 months

Tuesday 3rd March 2009
quotequote all
Hi
If you fit an ACT induction kit do you have to have the engine re-mapped?

Roy

Edited by chim on Tuesday 3rd March 11:56

ph1l5

5,027 posts

233 months

Tuesday 3rd March 2009
quotequote all
chim said:
Hi
If you fit an ACT induction kit do you have to have the engine re-mapped?

Roy

Edited by chim on Tuesday 3rd March 11:56
no, just a direct replacements for what you already have. but its a smooth pipe rather than ridges.

chim

245 posts

228 months

Tuesday 3rd March 2009
quotequote all
ph1l5 said:
chim said:
Hi
If you fit an ACT induction kit do you have to have the engine re-mapped?

Roy

Edited by chim on Tuesday 3rd March 11:56
no, just a direct replacements for what you already have. but its a smooth pipe rather than ridges.
Thanks Phil

Roy

Barreti

6,689 posts

268 months

Tuesday 3rd March 2009
quotequote all
You'll possibly need to cut them though. Remember, measure twice / cut once.
The 90deg is easy to get right, the one connected to the air filter is a bit more difficult.
I've found a hacksaw is good on Silicone hoses - I know, but it is, honestly.

K4TRV

1,819 posts

283 months

Tuesday 3rd March 2009
quotequote all
Barreti said:
You'll possibly need to cut them though. Remember, measure twice / cut once.
The 90deg is easy to get right, the one connected to the air filter is a bit more difficult.
I've found a hacksaw is good on Silicone hoses - I know, but it is, honestly.
+1 clap

trackcar

6,453 posts

257 months

Tuesday 3rd March 2009
quotequote all
Barreti said:
You'll possibly need to cut them though. Remember, measure twice / cut once.
The 90deg is easy to get right, the one connected to the air filter is a bit more difficult.
I've found a hacksaw is good on Silicone hoses - I know, but it is, honestly.
The ACT hoses don't look silicone, they're more a rubbery (Japanese for lovely?) texture and as such probably don't suffer from "furry edge" problems that you get when chopping normal silicone hoses with something like a hacksaw, so on that basis I would argue a hacksaw is probably quite a good tool to use, confirm with ACT if unsure though. It would be possible to have different pipes made in different lengths, but I know that my own silicone hose moulds cost 300 pounds each to make and I have 4 of them just for my cerb induction kits, that's a lot of investment to get back before you turn a profit .. so making them slightly oversize and cutting down to suit is by far the best option. Hacksaw away smile The 90 deg bend is proven certainly to be a significant hp improver even on std cars. thumbup

spend

12,581 posts

282 months

Tuesday 3rd March 2009
quotequote all
I think it may have been Tim himself that once posted something to the effect the silicone hose had 'deformed' too much so he had them made out of a material (rubberish) that was less malleable?

Pushrod-Power

233 posts

216 months

Tuesday 3rd March 2009
quotequote all
Much neater job is acheived if you use a fresh stanley bladed knife and use the hose clips as your hard edge then cut around the hose,use the supplied stainless steel joiner in the kit to keep the end your cutting round when your doing this(stop hose deforming collapsing)the rubber hose that ACT supply cuts a treat using this method,remember as already suggested measure twice cut once wink