Possible to remove piston through sump?
Possible to remove piston through sump?
Author
Discussion

VerySideways

Original Poster:

10,272 posts

303 months

Friday 6th March 2009
quotequote all
Ok, since doing the valve stem seals i don't think my oil consumption has significantly improved and it's still sooting up plug number 3 (second cylinder from the front, left hand bank) so i can only guess it's rings.
I'll do a compression test to be sure, but does anyone know if you can remove the piston from underneath (rather than taking off the head)?

What i'd like to do is drain the oil, take the sump off, and then undo the conrod for #3 and then drop the conrod and piston out, put some new rings in there, and then put the piston back in.

I would imagine it's possible but would like to hear if anyone else has done this before...

Can't be that hard can it?

Pushrod-Power

233 posts

216 months

Friday 6th March 2009
quotequote all
Sorry Sideways,cant be done wink

VerySideways

Original Poster:

10,272 posts

303 months

Friday 6th March 2009
quotequote all
Head off then?

Pushrod-Power

233 posts

216 months

Friday 6th March 2009
quotequote all
VerySideways said:
Head off then?
Afraid so frown if it was mine i would remove both heads,hone the bores and replace all the piston rings and change the end bearings,job done.

VerySideways

Original Poster:

10,272 posts

303 months

Friday 6th March 2009
quotequote all
I'm assuming inlet manifold has to come off too right, valley gasket, etc.?
If i'm doing that it's almost worth swapping the cam isn't it? (4.0, 52k miles)

Barkychoc

7,848 posts

235 months

Friday 6th March 2009
quotequote all
Are you sure it is soot on the plugs? - If it was rings it would be oil on the plugs not soot.
Make sure you're going down the right path first!

If it is sooty you could try swapping the injector with another one to see if the sooting up problem moves to another cylinder with the injector. Could be an injector sticking / stuck but thats a wild armchair mechanic guess!

VerySideways

Original Poster:

10,272 posts

303 months

Friday 6th March 2009
quotequote all
Sorry, should have clarified, the plug is covered in "black" but the fuel consumption is good, the performance is good, and it's consumed around three litres of oil in the last thousand miles!
When i took the Y piece out to remove the precats i noticed a lot more "black" on the left hand bank than the right hand, and three of the four plugs on the left hand bank are perfect.

Hence i deduced that it's likely to be oil rather than fuel which is blacking up the plug, and since i've just done the valve stem seals and that doesn't seem to have affected the oil consumption i'm going for rings...

Pushrod-Power

233 posts

216 months

Friday 6th March 2009
quotequote all
Agree with the above.......but how much oil are you using?

spend

12,581 posts

282 months

Friday 6th March 2009
quotequote all
Have you ever cleaned out the breather pipes / filters / flame trap.?

Just lifting the plenum to see the T.Base gives you an idea of what gunge is being sucked in - and plenty have 'modded?' the engine breathing.

I'd have the sump and plenum off to look up at the bores and inspect the inlets before making any decisions.

If you have to rebuild, think very carefully what you want to do... This chucking std parts back in can really be a wasted opportunity.

VerySideways

Original Poster:

10,272 posts

303 months

Friday 6th March 2009
quotequote all
Plenum is fine, and whilst i haven't cleaned the flame trap/breathers as i said one out of eight plugs is looking really poor, and the other seven are in fine fettle.

Agree though, if i'm going to re-ring all eight rather than just one then you have to start thinking what else i "may as well do" at the same time...

GreenV8S

31,027 posts

315 months

Friday 6th March 2009
quotequote all
A leakdown test can be a good way to tell whether you have a top end or bottom end problem, and even which cylinder it's associated with in some cases. The idea is that you feed a regulated supply of compressed air in to each cylinder in turn, measure the leakage rate and listen to find where there leak is coming from.

Edited by GreenV8S on Friday 6th March 13:41

VerySideways

Original Poster:

10,272 posts

303 months

Friday 6th March 2009
quotequote all
Looks like i'm taking the car to Dave Batty next week for compression/leakdown.

K4TRV

1,819 posts

283 months

Friday 6th March 2009
quotequote all
There are such things as bad/poorly performing spark plugs...........??

Check and double check......it's usually cheaper.