Help she will not start
Discussion
I am so frustrated..... grrrr
She will not start. As I am turning the ignition to on, I have the lights coming on, but as soon as the fuel pump starts to prime I loose all electrics except for the electric windows and the interior light. After a pause immobiliser LED starts flashing.
If I have left the key in the on position the engine, battery etc lights come on momentarily and then go off again (followed by the the buzzing sound from the engine bay that I normally hear if have turned the ignition to on and then off without cranking the engine).
If I turn the ignition to off and wait for 5 minutes it behaves as I described abve with the lights staying on until the pump starts priming.
She does not crank at any point and the battery is charged up.
Any ideas? I have have the car back and forth from the garage since November covering under 100miles in my hands. This developed after a starter motor change. The started motor was changed to fix the problem of the engine loosing all electrics (except for windows and interior light) while on the go, happening more frequently while going over bumps. This problem only started happening after the engine was taken out and replaced by the same garage.
Give me any thoughts on this please.
She will not start. As I am turning the ignition to on, I have the lights coming on, but as soon as the fuel pump starts to prime I loose all electrics except for the electric windows and the interior light. After a pause immobiliser LED starts flashing.
If I have left the key in the on position the engine, battery etc lights come on momentarily and then go off again (followed by the the buzzing sound from the engine bay that I normally hear if have turned the ignition to on and then off without cranking the engine).
If I turn the ignition to off and wait for 5 minutes it behaves as I described abve with the lights staying on until the pump starts priming.
She does not crank at any point and the battery is charged up.
Any ideas? I have have the car back and forth from the garage since November covering under 100miles in my hands. This developed after a starter motor change. The started motor was changed to fix the problem of the engine loosing all electrics (except for windows and interior light) while on the go, happening more frequently while going over bumps. This problem only started happening after the engine was taken out and replaced by the same garage.
Give me any thoughts on this please.
I am not too sure, i would look at easy stuff sounds like a bad connection if it happens over bumps check the 100 amp fuse mine worked lose this week and caused a few issues i would just check every fuse relay is tight in and a good visual around the car all connectors are how the should be
Thanks, I have already checked all fuses and relays except for the ones behind the dash. I thought that it might be a loose connection when it cut off over bumps, unfortunately now she will not even start in my garage. It is very frustrating as I have spent quite a bit of money with parts being changed by the garage and things getting worse rather than better.
I decided to try and "sort it out myself" this weekend but I have hit a wall...
I decided to try and "sort it out myself" this weekend but I have hit a wall...
I had my first "event" today when the beast wouldn't start, my approach was:
1) Go look through the bible
2) Get a multimeter and test every fuse including the ones behind the dash - some hanging out, clean & refit
3) Check sparkplugs - two leads were hanging nearly off, tighten up
4) Check stepper motor, connections wet, WD40
5) Still nothing, called the AA - "She's flooded mate", started it up first time and had a good drive
Bonus is now the idle is really smooth and it pulls harder... having all 8 cylinders probably helps
Hang in there bud, there has to be a solution!
Shabs
1) Go look through the bible
2) Get a multimeter and test every fuse including the ones behind the dash - some hanging out, clean & refit
3) Check sparkplugs - two leads were hanging nearly off, tighten up
4) Check stepper motor, connections wet, WD40
5) Still nothing, called the AA - "She's flooded mate", started it up first time and had a good drive
Bonus is now the idle is really smooth and it pulls harder... having all 8 cylinders probably helpsHang in there bud, there has to be a solution!
Shabs
First I'd start by checking the earth lead to the engine - particularly if the engine's been out and there's a fault that occurs when going over bumps. Second, and perhaps more likely, there's a black block connector between the ignition switch and the main loom - I'd make sure that all the connection are clean and secure.
Hut49 said:
First I'd start by checking the earth lead to the engine - particularly if the engine's been out and there's a fault that occurs when going over bumps. Second, and perhaps more likely, there's a black block connector between the ignition switch and the main loom - I'd make sure that all the connection are clean and secure.
Hmmmm I agree, the windows and interior light on my Chimaera work ALL the time ie. without key in ignition. I would therefore definately second Hut49's idea that it is ignition related and that black connector or even the ignition barrel would be a good place to start.Blue Chim said:
I am so frustrated..... grrrr
She will not start. As I am turning the ignition to on, I have the lights coming on, but as soon as the fuel pump starts to prime I loose all electrics except for the electric windows and the interior light. After a pause immobiliser LED starts flashing.
If I have left the key in the on position the engine, battery etc lights come on momentarily and then go off again (followed by the the buzzing sound from the engine bay that I normally hear if have turned the ignition to on and then off without cranking the engine).
If I turn the ignition to off and wait for 5 minutes it behaves as I described abve with the lights staying on until the pump starts priming.
She does not crank at any point and the battery is charged up.
Any ideas? I have have the car back and forth from the garage since November covering under 100miles in my hands. This developed after a starter motor change. The started motor was changed to fix the problem of the engine loosing all electrics (except for windows and interior light) while on the go, happening more frequently while going over bumps. This problem only started happening after the engine was taken out and replaced by the same garage.
Give me any thoughts on this please.
Either you are getting a brown-out on the switched ignition feed, or the alarm/immob is triggering and isolating it. Normally I'd expect that to stay isolated until it was disarmed, so a brown-out would be more likely. This sounds like an escalation of the original problem you mention, and I'd say you probably have a poor contact in the ignition circuit somewhere. Unfortunately these problems can be intermittent and need a significant load to show up, but if you are able to reproduce it every time you turn the ignition on then it's just a matter of following the circuit between the ignition switch and the coil and ECU to find where the loss occurs. The coil +ve terminal is a good place to start your testing.She will not start. As I am turning the ignition to on, I have the lights coming on, but as soon as the fuel pump starts to prime I loose all electrics except for the electric windows and the interior light. After a pause immobiliser LED starts flashing.
If I have left the key in the on position the engine, battery etc lights come on momentarily and then go off again (followed by the the buzzing sound from the engine bay that I normally hear if have turned the ignition to on and then off without cranking the engine).
If I turn the ignition to off and wait for 5 minutes it behaves as I described abve with the lights staying on until the pump starts priming.
She does not crank at any point and the battery is charged up.
Any ideas? I have have the car back and forth from the garage since November covering under 100miles in my hands. This developed after a starter motor change. The started motor was changed to fix the problem of the engine loosing all electrics (except for windows and interior light) while on the go, happening more frequently while going over bumps. This problem only started happening after the engine was taken out and replaced by the same garage.
Give me any thoughts on this please.
I have been testing the fuses - all are OK. And I am testing the relays, the bible says the I should be getting 100 - 1000 ohms. I am getting 70- 80 ohms on the control coil. I am getting this on all relays, so I worked with the assumption of this being OK. Am I wright?
The two metal Bosch relays on the ECU wires give me no readings at all, are they non-mechanical? I have swapped them round with no positive result.
The two metal Bosch relays on the ECU wires give me no readings at all, are they non-mechanical? I have swapped them round with no positive result.
Find a good earth, for example the battery -ve terminal.
Connect the volt meter -ve lead to the earth using croc clips or whatever, and leave it connected. Ideally connect it with a couple of yards of wire so you can move the meter around the car without disturbing these connections.
I assume you have the housing off the steering column to get access to the back of the ignition switch.
Being careful not to short anything, measure the voltage on the power lead into the switch, you should see around 12.5 volts. Switch the ignition on (the pump runs, everything goes dead etc etc) and the voltage you are measuring should not change at all.
If that is OK then move the meter +ve lead to the switched ignition output terminal on the switch. With the ignition off it should read 0V. Switch the ignition on. It should now read the same as you were getting on the power input lead (12.5V or so).
If that is OK then move the meter +ve lead to the +ve terminal on the ignition coil, under the bonnet on the side of the plenum. There are two terminals on the coil which will be marked +ve and -ve, be sure to get the +ve one. Switch the ignition on and you should see the same voltage here as you were getting at the switch.
If any of those tests fail then then will point you directly to a wiring fault.
Connect the volt meter -ve lead to the earth using croc clips or whatever, and leave it connected. Ideally connect it with a couple of yards of wire so you can move the meter around the car without disturbing these connections.
I assume you have the housing off the steering column to get access to the back of the ignition switch.
Being careful not to short anything, measure the voltage on the power lead into the switch, you should see around 12.5 volts. Switch the ignition on (the pump runs, everything goes dead etc etc) and the voltage you are measuring should not change at all.
If that is OK then move the meter +ve lead to the switched ignition output terminal on the switch. With the ignition off it should read 0V. Switch the ignition on. It should now read the same as you were getting on the power input lead (12.5V or so).
If that is OK then move the meter +ve lead to the +ve terminal on the ignition coil, under the bonnet on the side of the plenum. There are two terminals on the coil which will be marked +ve and -ve, be sure to get the +ve one. Switch the ignition on and you should see the same voltage here as you were getting at the switch.
If any of those tests fail then then will point you directly to a wiring fault.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



