PAS Leak - Advice Required
Discussion
I've just spotted a pool of 'oil' under the front offside corner of the car (95 Chim 400HC).
Jacked it up and it's PAS fluid, and it's sprayed liberally all over everything underneath (mixed into nice patterns with the Mobil 1 that's seeping from the back of the sump?!?!).
Started getting annoyed as it had a recon rack fitted in November and couldn't believe that this could have given up already...
Long and short of it is that the rubber hose that goes into the top union on the rack has been just touching the big central exhaust pipe, the down pipe from the y-piece, when on full lock and has melted a small hole in the hose.
Is this a TVR specific part and is it an easy job to replace and recharge the PAS system, or am I going to have to 'squirt' my way to a garage?!
Could I splice in a repair with some tubing? Does anyone know the internal diameter of the PAS hose?
Cheers
Giles
PS. Off to shower in brake fluid now just to complete the full 'lubricated' look!
PPS. Tightened the sump bolts while I was under there - will re-seal sump once I have sorted the PAS!
Jacked it up and it's PAS fluid, and it's sprayed liberally all over everything underneath (mixed into nice patterns with the Mobil 1 that's seeping from the back of the sump?!?!).
Started getting annoyed as it had a recon rack fitted in November and couldn't believe that this could have given up already...
Long and short of it is that the rubber hose that goes into the top union on the rack has been just touching the big central exhaust pipe, the down pipe from the y-piece, when on full lock and has melted a small hole in the hose.
Is this a TVR specific part and is it an easy job to replace and recharge the PAS system, or am I going to have to 'squirt' my way to a garage?!
Could I splice in a repair with some tubing? Does anyone know the internal diameter of the PAS hose?
Cheers
Giles
PS. Off to shower in brake fluid now just to complete the full 'lubricated' look!
PPS. Tightened the sump bolts while I was under there - will re-seal sump once I have sorted the PAS!
Edited by Clippy on Thursday 19th March 14:12
OK - may have answered my own question... 
Assume that as hose has jubilee rather than pressure fitting that it is the return hose to the reservoir and, on that basis could be spliced or patched short-term to keep the car OTR while I get a replacement hose?
G
PS. Brake fluid shower appears to have removed most dirt and some skin...is this what they use for 'chemical peels' at spa hotels?!

Assume that as hose has jubilee rather than pressure fitting that it is the return hose to the reservoir and, on that basis could be spliced or patched short-term to keep the car OTR while I get a replacement hose?
G
PS. Brake fluid shower appears to have removed most dirt and some skin...is this what they use for 'chemical peels' at spa hotels?!

If it's got the jubilee clip then it's just a case of replacing said length with appropriate type piping. Not worth repairing and not too bad of a job. When refilling the system I just turned steering fully left and right(engine running) until all air was gone and just topped up reservoir accordingly. You will know when all air is expelled when the the steering goes quiet.
Got my hose from www.pirtek.co.uk invoice shows
100R6-08 2Meter
100R6-10 1Meter
Cost about £20, this was enough to replace all the pas pipes which use the jubelee clips.
100R6-08 2Meter
100R6-10 1Meter
Cost about £20, this was enough to replace all the pas pipes which use the jubelee clips.
Cheers everyone!
I've ordered a new hose from the TVR Shop and, so I can use the car over the weekend until it arrives, I've 'bandaged' the section with the pin-hole with another section of hose, plenty of contact adhesive and some jubilee clips...
Tomorrow I might even dare to start it up and see whether or not it still leaks!
Now for a quick pint of Castrol TQF and bed!
I've ordered a new hose from the TVR Shop and, so I can use the car over the weekend until it arrives, I've 'bandaged' the section with the pin-hole with another section of hose, plenty of contact adhesive and some jubilee clips...
Tomorrow I might even dare to start it up and see whether or not it still leaks!
Now for a quick pint of Castrol TQF and bed!
Gassing Station | Chimaera | Top of Page | What's New | My Stuff




ds IMHO 
