vacuum advance
Discussion
With distributor cap off I disconected the vacuum tube from plenum and sucked on it (as you do !) to check that the plate was moving in the distributor.
Now you cant actually see much due to the sheild that is fitted, but nothing appeared to happen. I can see a bit through the aperture in the sheild, but nothing there moved. I could not hear anything either, I remember on my old cars that had a vacuum advance that when you let the vacuum go, you could hear the spring return the plate. Nothing
Should I remove the sheild to check ?
It may look like I am having lots of problems from my number of posts lately, but I am not. Just the one of flooding/sooty plugs and 'not quite right' situatiion I have at the moment.
As I am at work and cant actually get to do anything, but I cant help thinking about it.
Now you cant actually see much due to the sheild that is fitted, but nothing appeared to happen. I can see a bit through the aperture in the sheild, but nothing there moved. I could not hear anything either, I remember on my old cars that had a vacuum advance that when you let the vacuum go, you could hear the spring return the plate. Nothing
Should I remove the sheild to check ?
It may look like I am having lots of problems from my number of posts lately, but I am not. Just the one of flooding/sooty plugs and 'not quite right' situatiion I have at the moment.
As I am at work and cant actually get to do anything, but I cant help thinking about it.
Edited by WokingWedger on Friday 20th March 10:53
Edited by WokingWedger on Friday 20th March 10:54
if it sticks on your tongue its working .some v8 specialist do away with the vac advance ,you can advance the timming a little to gain more power up the rev range , these standard dizzys dont give enough advance thats why you can upgrade to a mallory .
Edited by daz the plumber on Friday 20th March 11:01
blitzracing said:
Daz's trick will tell you its not got a hole in the diaphram, but the plate it drives could still be stuck. You could try starting the engine, and then sucking the pipe, as Id expect the tickover to change as the timming changes.
if you suck on that vacuum pipe while the engines is idling you will hear the engine speed step up noticeably 
Edited by That Daddy on Friday 20th March 13:04
daz the plumber said:
if it sticks on your tongue its working .some v8 specialist do away with the vac advance ,you can advance the timming a little to gain more power up the rev range , these standard dizzys dont give enough advance thats why you can upgrade to a mallory .
That doesn't show whether it's working or connected to the base plate, only that it doesn't leak.I hope there aren't any V8 specialists who would remove it on a road car. Even on a race car you'd be sacrificing throttle response, fuel economy and part throttle engine cooling for no good reason. (On a race car you're more likely to have mapped ignition anyway.)
GreenV8S said:
daz the plumber said:
if it sticks on your tongue its working .some v8 specialist do away with the vac advance ,you can advance the timming a little to gain more power up the rev range , these standard dizzys dont give enough advance thats why you can upgrade to a mallory .
That doesn't show whether it's working or connected to the base plate, only that it doesn't leak.I hope there aren't any V8 specialists who would remove it on a road car. Even on a race car you'd be sacrificing throttle response, fuel economy and part throttle engine cooling for no good reason. (On a race car you're more likely to have mapped ignition anyway.)
mine split shortly after purchase of my Chim and after fitting a new on it felt like i gained 15% more torque low down(got used to it not working)and that's something you cant sacrifice on a HC400,have never seen a good reason to bin a vacuum unit unless you are running sidedraughts or your foot is pinned to the floorpan all the time and we are not so...... 
Edited by That Daddy on Friday 20th March 20:18
OK then, no movement when sucking on the pipe and wont hold a vacuum when sticking your tongue in it. Thanks for reminding me of this little trick DAZ.
(do you use it in plumbing, or some where else hehehehe)
Removed vacuum unit and palte in distributor is free to move but arm from vacuum wont move when sucked.
Guess the diapghragm has gone.
Local motor factors dont stock them (I asked for Range rover item), so I guess I will have to order one from TVR Power. (unless anyone knows a cheaper source)
Another fine day wasted without my Chim.
(do you use it in plumbing, or some where else hehehehe)
Removed vacuum unit and palte in distributor is free to move but arm from vacuum wont move when sucked.
Guess the diapghragm has gone.
Local motor factors dont stock them (I asked for Range rover item), so I guess I will have to order one from TVR Power. (unless anyone knows a cheaper source)
Another fine day wasted without my Chim.
GreenV8S said:
Range Rover classic 3.9 is the correct part.
Don't let a duff vac advance unit stop you enjoying a sunny day, you could drive round for months with no great harm. But you should get it fixed because it'll go better, use less fuel and run cooler with the vac advance working properly.
Agree with that one Don't let a duff vac advance unit stop you enjoying a sunny day, you could drive round for months with no great harm. But you should get it fixed because it'll go better, use less fuel and run cooler with the vac advance working properly.
+1My vacuum advance unit packed up some time ago,
i got the numbers off the old one and went hunting.
After a few days searching from work and a few evenings on the internet,
the nearest non TVR match i could find only had about half of the advance degrees that the genuine TVR part has. So reluctantly i bought mine from Racing Green for about £70
perfect fit, problem solved.
Steve
i got the numbers off the old one and went hunting.
After a few days searching from work and a few evenings on the internet,
the nearest non TVR match i could find only had about half of the advance degrees that the genuine TVR part has. So reluctantly i bought mine from Racing Green for about £70
perfect fit, problem solved.
Steve
blitzracing said:
How is the advance controlled by the vacumme chamber itself ?? Id of thought the movement would be controlled by the sliding plate inside the distributor.
Mark
The amount of advance is controlled by the base plate within the dizzy. The vacuum level that it comes in at is controlled by the cannister, and it's possible to get cannisters that operate at lower pressures, but all our cars use completely standard ones.Mark
blitzracing said:
How is the advance controlled by the vacumme chamber itself ?? Id of thought the movement would be controlled by the sliding plate inside the distributor.
Mark
The VACUUM from small VACUUM pipe comes from the plenum chamber.Mark
This is just enough to pull the diaphragm a few millimeters, which pulls the small lever that goes into the distributor a few millimeters, which (using the lever principle) pulls the distributor back plate several millimeters.
(with some help from the mechanical weights) which equates to quite a high angular degrees figure.
I seem to remember it advances by something like 38 degrees !!!
But i may be mistaken on the exact figure.
just had look in the "Bible" but it doesn't seem to mention it. !!??
there you go, clear as mud now !!
Steve
Bensonv8 said:
I seem to remember it advances by something like 38 degrees !!!
It's possible to modify the dizzy to increase of decrease the amount of advance, but on a standard dizzy (35DLM8 or similar) there's 15 degrees of vac advance and 20 degrees of mech advance. Add the 8-12 degrees of static advance and you have the 28 - 32 total advance that you're thinking of.Gassing Station | Chimaera | Top of Page | What's New | My Stuff




