Induction hose collapse
Discussion
Hi all,
Have noticed that the induction hose between the air intake filter and the bulkhead has ruptured and partially collapsed where it turns the 90 degree bend. Tricky to find new hose but did find it somewhere for around £40.
My question is: Is it worth replacing with the smooth bore stuff - any power increases for smooth stuff - probably un-noticeable? It looks better but is also a lot more expensive. Someone on a different thread said that changing the 90 degree bend to the plenum made a difference. Then there's also the Piper cross filter replacement. I guess you could go all the way and change the plenum to but that's serious money then......mustn't get carried away !
Cheers,
Matt
Have noticed that the induction hose between the air intake filter and the bulkhead has ruptured and partially collapsed where it turns the 90 degree bend. Tricky to find new hose but did find it somewhere for around £40.
My question is: Is it worth replacing with the smooth bore stuff - any power increases for smooth stuff - probably un-noticeable? It looks better but is also a lot more expensive. Someone on a different thread said that changing the 90 degree bend to the plenum made a difference. Then there's also the Piper cross filter replacement. I guess you could go all the way and change the plenum to but that's serious money then......mustn't get carried away !
Cheers,
Matt
Hi Matt - I've definitely been considering this upgrade as it seems to be where the car is restricted in terms of 'breathing'. The smoother and wider you can make the hose the easier the air will flow into the engine because the less 'work' the engine will has to do to get it there. This is where you will see returns in terms of power - gains of between 5 - 10 seem to be standard.
Do the Air Filter too. A good quality one with low resistance will have the same effect as the smooth bore induction kit.
If you can afford the Carbon Fibre Trumpets, do them too then your induction system will be pretty well sorted!
blitzracing said:
Any one tried strapping an airfilter directly to the AFM ? OK so the airs hotter in the engine bay, but I bet the gains of cold air are outweighed by all that tubing...
I had plenum / 5AM / filter connected straight together, it seemed to work quite nicely. I haven't done any direct before/after power measurements so I don't know what the gains were, but the whole thing did go quite nicely. To prevent it pulling in hot air from the engine bay I put the filter in an air box that pulled from the gap between the bonnet and the windscreen. It did still pull in hot air when stationary, but as soon as it was moving the high pressure zone in front of the bonnet pushes cold fresh air in.debaron said:
Do the Air Filter too. A good quality one with low resistance will have the same effect as the smooth bore induction kit.
If you can afford the Carbon Fibre Trumpets, do them too then your induction system will be pretty well sorted!
Is the piper cross air filter a good one then? And, why are the carbon fibre trumpets so good. Is it due to a better shape of because they are carbon fibre ?If you can afford the Carbon Fibre Trumpets, do them too then your induction system will be pretty well sorted!
Cheers,
Matt
The standard air filters don't have the surface area of some of the aftermarket ones you can get. By increasing the surface area of an air filter you can lower it's resistance ie making it easier to pull air through.
This is achieved by the folds that you get in performance air filters. You still need it to filter out dust and other road crap so don't get too coarse a filter though!
My knowledge of the Carbon Fibre trumpets is limited but I do know that by shortening the length of the trumpets, you improve airflow at high revs ON A STANDARD SETUP - you may or may not notice them on a modded setup (aftermaket cam for example). Daz The Plumber for instance say's 'he doesn't think they are value for money' but I know Daz has some quite significant mods. In his case, I think there is already extra airflow into the engine as a result of his cam upgrade and other bits.
On the other hand, TVRJock has apparently had 'astonishing results' on his 400 by shortening his trumpets. Hard to say really what results they will have on your car. This guy said it made a difference:
http://woodys-tvr.blogspot.com/2006/11/induction-m...
Gassing Station | Chimaera | Top of Page | What's New | My Stuff




Having some kind of performance meter to readily compare mods is essential IMHO.