Refitting the mesh grill on a '95 Chimaera
Refitting the mesh grill on a '95 Chimaera
Author
Discussion

SteveW8975

Original Poster:

6,389 posts

215 months

Saturday 21st March 2009
quotequote all
I had to replace the indicator bulb last night, so took the grill out, scuffed my knuckles, replaced the bulb - easy.

However. A few hours of swearing, I'll be damned if I can get the mesh grill with the rubber surround back in place. Is there a trick to this? I've tried putting the top in first, the bottom in first, the sides in first, poked it with a thin screwdriver, tried puttng the rubber ring in, then putting the mesh in (daft idea!) and finally I gave up and got a pair of small self-tappers to hold in place as it's going dark and patience is even darker.

What's the answer?!

V8 Animal

6,015 posts

241 months

Saturday 21st March 2009
quotequote all
SteveW8975 said:
I had to replace the indicator bulb last night, so took the grill out, scuffed my knuckles, replaced the bulb - easy.

However. A few hours of swearing, I'll be damned if I can get the mesh grill with the rubber surround back in place. Is there a trick to this? I've tried putting the top in first, the bottom in first, the sides in first, poked it with a thin screwdriver, tried puttng the rubber ring in, then putting the mesh in (daft idea!) and finally I gave up and got a pair of small self-tappers to hold in place as it's going dark and patience is even darker.

What's the answer?!
Yeah have to agree a pain in the arse.
But it's a case of once youv'e done it a few times it get's easier.
Still dread it though.
How i tackle it.
Put bottom in first and bow it so you can get both ends a part way in the gasket.
Then i use a flat blade screwdriver to wiggle the gasket over the top of the grill working from one corner to the middle.
Keep levering down to push the grill fully down into the gasket.
Once youv'e reached the middle and one side is in go over to other corner and leaver the grill towards the corner you have done it will help position the grill better and make your last corner easier.
Be carefull with the screwdriver you can easy slip with temper and scratch your paint.
Hope that helps looks awful without the grill.

Red Cabbage

3,606 posts

263 months

Saturday 21st March 2009
quotequote all
I slide it in from the RH side until it is in all the way from the left to the middle. Then gently pull the seal back, like fitting a windscreen with the old style rubber, to get the other side in.

Golflion

2,782 posts

252 months

Saturday 21st March 2009
quotequote all
V8 Animal said:
SteveW8975 said:
I had to replace the indicator bulb last night, so took the grill out, scuffed my knuckles, replaced the bulb - easy.

However. A few hours of swearing, I'll be damned if I can get the mesh grill with the rubber surround back in place. Is there a trick to this? I've tried putting the top in first, the bottom in first, the sides in first, poked it with a thin screwdriver, tried puttng the rubber ring in, then putting the mesh in (daft idea!) and finally I gave up and got a pair of small self-tappers to hold in place as it's going dark and patience is even darker.

What's the answer?!
Yeah have to agree a pain in the arse.
But it's a case of once youv'e done it a few times it get's easier.
Still dread it though.
How i tackle it.
Put bottom in first and bow it so you can get both ends a part way in the gasket.
Then i use a flat blade screwdriver to wiggle the gasket over the top of the grill working from one corner to the middle.
Keep levering down to push the grill fully down into the gasket.
Once youv'e reached the middle and one side is in go over to other corner and leaver the grill towards the corner you have done it will help position the grill better and make your last corner easier.
Be carefull with the screwdriver you can easy slip with temper and scratch your paint.
Hope that helps looks awful without the grill.
+1 but what a sod to get on,took me over an hour first time fingers and patience in tatters....just when you think its in it pops out..mmmmmm sounds familiar!!!rolleyes

V8 Animal

6,015 posts

241 months

Saturday 21st March 2009
quotequote all


+1 but what a sod to get on,took me over an hour first time fingers and patience in tatters....just when you think its in it pops out..mmmmmm sounds familiar!!!rolleyes
[/quote]

I slide it in from the RH side until it is in all the way from the left to the middle. Then gently pull the seal back

What was the topic again ive had a fewhehe

Golflion

2,782 posts

252 months

Saturday 21st March 2009
quotequote all
mmmmmmmmmm??biglaugh

spend

12,581 posts

282 months

Sunday 22nd March 2009
quotequote all
Give the rubber a bloomin good clean while the grill is out, then spray the inside with silicone rubber lubricant or the like. Makes it much easier, as does a little warmer weather (for the fingers as well as the rubber hehe).

Red Cabbage

3,606 posts

263 months

Sunday 22nd March 2009
quotequote all
V8 Animal said:
+1 but what a sod to get on,took me over an hour first time fingers and patience in tatters....just when you think its in it pops out..mmmmmm sounds familiar!!!rolleyes
V8 Animal said:
I slide it in from the RH side until it is in all the way from the left to the middle. Then gently pull the seal back

What was the topic again ive had a fewhehe
You didn't read my post either! drunk

Edited by Red Cabbage on Sunday 22 March 08:46

Badmutha

658 posts

224 months

Sunday 22nd March 2009
quotequote all
spend said:
Give the rubber a bloomin good clean while the grill is out, then spray the inside with silicone rubber lubricant or the like. Makes it much easier, as does a little warmer weather (for the fingers as well as the rubber hehe).
Neat washing-up liquid is a handy alternative

spend

12,581 posts

282 months

Sunday 22nd March 2009
quotequote all
Washing up liquid might be good for a moment... but if you are stuck in the middle of Europe & need to change a bulb, you might appreciate my method more hehe

Been there & done it..... but I do have a different fixing now using screws since I redesigned the whole undertray / grille laugh

SteveW8975

Original Poster:

6,389 posts

215 months

Sunday 22nd March 2009
quotequote all
Cheers fellas - I'll give it another bash this afternoon.

I did notice how grubby the seal was yesterday when i took it off, so scraped out all of the gunk then, but washing up liquid/silicon spray/ky jelly sounds a helpful option!

Badmutha

658 posts

224 months

Sunday 22nd March 2009
quotequote all
SteveW8975 said:
Cheers fellas - I'll give it another bash this afternoon.

I did notice how grubby the seal was yesterday when i took it off, so scraped out all of the gunk then, but washing up liquid/silicon spray/ky jelly sounds a helpful option!
yikes don't waste the ky jelly!!!

V8 Animal

6,015 posts

241 months

Sunday 22nd March 2009
quotequote all
Badmutha said:
SteveW8975 said:
Cheers fellas - I'll give it another bash this afternoon.

I did notice how grubby the seal was yesterday when i took it off, so scraped out all of the gunk then, but washing up liquid/silicon spray/ky jelly sounds a helpful option!
yikes don't waste the ky jelly!!!
What's that stuff?hehe

SpudMurphy

164 posts

250 months

Sunday 22nd March 2009
quotequote all
Please forgive me for being blunt guys but you're all p***ing into the wind with your KY, washing up liquid, silicone lubricant and whatever you're having yourself solutions to the front grill refitting problem.

It's a complete nightmare. Abandon the old grill/fixing method while you still have some sanity and some knuckle skin left.

When I had a little wet weather 'off' a couple of years back, I thankfully lost my front grille and never found it again. I got a replacement from David Gerald TVR (THE GREEN, INKBERROW, WORCESTER WR7 4JF Tel: 44 (0)1386 793237 which had the surround shrunk onto the grille. I fixed it to the two diagonal bars behind the grill with two self-tappers and problem sorted.



Changing a bulb now takes two minutes not two days.

I have no idea whether they still have them in stock but they couldn't have been more helpful when I was trying to source mine.

Hope this helps.

spend

12,581 posts

282 months

Sunday 22nd March 2009
quotequote all
SpudMurphy said:
...When I had a little wet weather 'off' a couple of years back.....got a replacement from David Gerald WORCESTER....
You really need to take the ferry when you come over for parts nutshehe

roysum

961 posts

220 months

Saturday 11th April 2009
quotequote all
SpudMurphy said:
Please forgive me for being blunt guys but you're all p***ing into the wind with your KY, washing up liquid, silicone lubricant and whatever you're having yourself solutions to the front grill refitting problem.

It's a complete nightmare. Abandon the old grill/fixing method while you still have some sanity and some knuckle skin left.

When I had a little wet weather 'off' a couple of years back, I thankfully lost my front grille and never found it again. I got a replacement from David Gerald TVR (THE GREEN, INKBERROW, WORCESTER WR7 4JF Tel: 44 (0)1386 793237 which had the surround shrunk onto the grille. I fixed it to the two diagonal bars behind the grill with two self-tappers and problem sorted.



Changing a bulb now takes two minutes not two days.

I have no idea whether they still have them in stock but they couldn't have been more helpful when I was trying to source mine.

Hope this helps.
+1, used some tight fitting black grommet strip from Halfrauds, needed to heat it with a hair dryer and superglue around the bends. Now fixed with two self tapers, the heads of which blackened with permanent marker. Job done !

steviegasgas

417 posts

216 months

Saturday 11th April 2009
quotequote all
Good idea that, another one is if you ever run out of KY Jelly then I find foreplay works nearly as well!! Its an old one but still bit funny!

SteveW8975

Original Poster:

6,389 posts

215 months

Saturday 11th April 2009
quotequote all
I forgot about this thread...

I went for the SpudMurphy self tappers in the end - japanned black head ones so pretty much invisble. I value my knuckles too much to be doing with all the faffing.

spend

12,581 posts

282 months

Sunday 12th April 2009
quotequote all
Hmmm, when mine was only attached with 2 central fixings it rattled like skeletons fornicating.. I subsequently used 4 fixings at the edges of the cross braces, it still flapped a bit until I added another two at the sides. This has been fine with the mesh and punched ally versions. 6 screws are still a lot easier than the tight rubber fitment redfaceooer: hehe

lifebegins@400

217 posts

231 months

Tuesday 14th April 2009
quotequote all
fair point with the fixings etc but it's just a matter of practice tbh - have got it down to 20 mins now using fairy liquid or other suitable lubricant - cue more double entendres!! sperm