Remove Plenum / Carbon Fibre Trumpets
Discussion
Hello all, was doing my injectors today, wanted to get them out without removing the plenum ideally.
It doesen't look like that's going to me possible however so can someone give me a run down of how to properly remove the plenum.
While I'm there I'm going to do the carbon fibre trumpets. Any tips on doing those too? I read something about putting the trumpet base in the oven!?
Cheers
Ryan
i have carbon trumpets , tell you the truth i have not noticed much difference,they are expensive, why not go the whole hogg , replace the plenum for a larger bored out 72mm throttle body,replace the trumpets base and eather have aluminium 45mm trumpets or just blended, then get a ported inlet manifold . now that will make a differene and you will be surprisedd how much you can get the lot for . i don`t feel the carbon trumpets are value for money .!
If you just start from the top and work down it is pretty obvious how the fuel rail comes off. You have to get the plenum top off to get at the bolts for the trumpet base, and the trumpet base has to come off to let the fuel rail come up far enough to release the injectors.
You should be aware that the fuel rail can hold fuel under pressure many hours after the pump stops. You should also be aware that it's extremely easy to damage the injector O rings so ensure the fuel rail and manifold are surgically clean before you try to reinstall the injectors.
Also be paranoid about dropping stuff into the exposed intake while you're working on it. It's amazing how nuts, washers and so on can cling to a spanner and wait for you to swing it over the engine before they fall off. If you notice stuff falling in, you can waste days fishing it out again. And if you don't notice it's all to easy to wreck the engine when you come to start it next time. Be sure to tape over the exposed holes as soon as possible and meantime be very cautious about dropping stuff in.
The standard trumpets are glued in, sometimes literally drop out on their own but sometimes need the trumpet base heating to expand and release them. Try carefully pulling them out, if that won't work then 100C in the oven for an hour or so then carefully pull the trumpets out with a pair of pliers and some oven mits.
You should be aware that the fuel rail can hold fuel under pressure many hours after the pump stops. You should also be aware that it's extremely easy to damage the injector O rings so ensure the fuel rail and manifold are surgically clean before you try to reinstall the injectors.
Also be paranoid about dropping stuff into the exposed intake while you're working on it. It's amazing how nuts, washers and so on can cling to a spanner and wait for you to swing it over the engine before they fall off. If you notice stuff falling in, you can waste days fishing it out again. And if you don't notice it's all to easy to wreck the engine when you come to start it next time. Be sure to tape over the exposed holes as soon as possible and meantime be very cautious about dropping stuff in.
The standard trumpets are glued in, sometimes literally drop out on their own but sometimes need the trumpet base heating to expand and release them. Try carefully pulling them out, if that won't work then 100C in the oven for an hour or so then carefully pull the trumpets out with a pair of pliers and some oven mits.
The throttle assembly and the plenum top all come off together. You can leave the throttle cable connected, just find somewhere to rest the plenum top out of the way that doesn't strain the cable. If that isn't convenient, it only needs a split pin to release the inner and a big adjustable to undo the locking nut on the outer, to separate the cable from the plenum/throttle assembly.
Remove the throttle cable, you need all the space you can get to manipulate the plenum off over the trumpets. You will have to aggressively bend the grill up to get the thing off. Shorter trumpets do make it a little easier - but for Chim bodywork a blended base wins everytime IMHO - you are going to find out what I mean very shortly 
4.. litre flared trumpets come out easy with a little roasting followed by a wiggle, its the ported base 'scaffold' tubes that I've found much tougher to remove
Its much easier to get the parts dipped or bead blasted than spending ages trying to clean them up BTW.

4.. litre flared trumpets come out easy with a little roasting followed by a wiggle, its the ported base 'scaffold' tubes that I've found much tougher to remove

Its much easier to get the parts dipped or bead blasted than spending ages trying to clean them up BTW.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



