Exhaust manifold shopping
Exhaust manifold shopping
Author
Discussion

900T-R

Original Poster:

20,406 posts

288 months

Monday 23rd March 2009
quotequote all
So the good news on this morning's MOT was that my Chimmie was granted one without any expenditure needed other than the test itself bouncewoohoo ; emissions were said to be perfect, chassis in good order, even the brakes were given a clean bill of health for the next year so the box with the Tower View larger discs upgrade is back on its shelf for another 12 months.
The 'bad' news is that there's a small list of things that will need sorting before the next MOT, the most prominent one being a leak developing in the left hand side exhaust manifold. Interestingly, the tester (who just got a 10/10 for his biannual MOT refreshment course exams party ) found that based on what's in the vehicle identification papers, my car isn't obliged to have a catalyst ('vehicles carrying codes (....): if a catalytic converter and/or lambda sensor aren't present on the vehicle inspected, the tester may assume that they were not fitted by the vehicle manufacturer') and recommended a decat (and switch to the 'green' tune resistor for the ECU).

Now if there's one thing I like it's shopping - for shiny TVR stuff, that is! paperbag - and I've got some time to save up before it becomes an issue, anyway, so I'm not exactly mortified. wink

Soooo get to the bl00dy point Eric I'm looking for something to replace the std manifolds and Y-piece with that a) doesn't cost a king's ransom, b) bolts straight on in the way the OE stuff does so as not to jeopardise the estimated 4 hrs shop time for replacing both manifolds and Y-piece and c) gives maximum bang for buck in terms of performance and longeivity (there's already one or two new manifolds in the car's service history so far).

Recommendations? biggrin




900T-R

Original Poster:

20,406 posts

288 months

Monday 23rd March 2009
quotequote all
tumbleweed

Chimjunkie

2,879 posts

242 months

Monday 23rd March 2009
quotequote all
Have to say that Spyschim has the best sounding exhaust i have heard. Not talking loud, just awesome note. His is a decatted 400 with the ACT sports manifolds. Think the rest of the system is standard.

Edited by Chimjunkie on Monday 23 March 20:16

Uncle Fester

3,114 posts

239 months

Monday 23rd March 2009
quotequote all
http://www.v8enhancements.co.uk/

Shinier than my head, louder than the wife when I’m in the doghouse, but much better sounding.

thumbup

griffdude

1,938 posts

279 months

Monday 23rd March 2009
quotequote all
Uncle Fester said:
http://www.v8enhancements.co.uk/

Shinier than my head, louder than the wife when I’m in the doghouse, but much better sounding.

thumbup
They also gave me an extra 27hp & 50lb/ft.

300bhp/ton

41,030 posts

221 months

Monday 23rd March 2009
quotequote all
900T-R said:
So the good news on this morning's MOT was that my Chimmie was granted one without any expenditure needed other than the test itself bouncewoohoo ; emissions were said to be perfect, chassis in good order, even the brakes were given a clean bill of health for the next year so the box with the Tower View larger discs upgrade is back on its shelf for another 12 months.
The 'bad' news is that there's a small list of things that will need sorting before the next MOT, the most prominent one being a leak developing in the left hand side exhaust manifold. Interestingly, the tester (who just got a 10/10 for his biannual MOT refreshment course exams party ) found that based on what's in the vehicle identification papers, my car isn't obliged to have a catalyst ('vehicles carrying codes (....): if a catalytic converter and/or lambda sensor aren't present on the vehicle inspected, the tester may assume that they were not fitted by the vehicle manufacturer') and recommended a decat (and switch to the 'green' tune resistor for the ECU).

Now if there's one thing I like it's shopping - for shiny TVR stuff, that is! paperbag - and I've got some time to save up before it becomes an issue, anyway, so I'm not exactly mortified. wink

Soooo get to the bl00dy point Eric I'm looking for something to replace the std manifolds and Y-piece with that a) doesn't cost a king's ransom, b) bolts straight on in the way the OE stuff does so as not to jeopardise the estimated 4 hrs shop time for replacing both manifolds and Y-piece and c) gives maximum bang for buck in terms of performance and longeivity (there's already one or two new manifolds in the car's service history so far).

Recommendations? biggrin
Glad everything else seems good on the Chim smile

Not sure what manifolds are available but what you want are long tube headers. This is because for a n/a motor exhaust scavenging is far more important than outright flow. In fact many standard manifolds actually flow quite well for the stock level of HP, so unless massivly upping the power levels only minimal gains will be seen by flow increase.

In order to scavnege the primaries need to be long, the longer the better as it will promote scavenging at lower rpms, and as we all know the Rv8 is hardly a revver at the best of times.

900T-R

Original Poster:

20,406 posts

288 months

Tuesday 24th March 2009
quotequote all
griffdude said:
Uncle Fester said:
http://www.v8enhancements.co.uk/

Shinier than my head, louder than the wife when I’m in the doghouse, but much better sounding.

thumbup
They also gave me an extra 27hp & 50lb/ft.
Unfortunately Clive's headers seem to fail in the 'not a kings ransom' and 'bolt right on' departments... frown

clive f

7,259 posts

264 months

Tuesday 24th March 2009
quotequote all
they will bolt right on , just need to move a water pipe, but not quick an easy to make I`m afraid.

900T-R

Original Poster:

20,406 posts

288 months

Wednesday 25th March 2009
quotequote all
I know they're good value Clive, just not in relation to the value of the average Chim though... hehe If I could afford them, it would be a question of whether the dealer technician would be OK with changing the water pipe run and whatnot (all cars are different) and then I'd still reckon it would cost a fair bit more because of it being the 1st time they were installed over here - all of a sudden you're looking at £3K+ yikes

Anyway... WTF is up with this here http://cgi.ebay.co.uk/TVR-ROVER-V8-EXHAUST-MANIFOL... ?



On the right side of the pic a pre-cat manifold, on the left ????




900T-R

Original Poster:

20,406 posts

288 months

Wednesday 25th March 2009
quotequote all
Right, options found so far.

  • SH std de-precat manifolds + this:


Pros: seems to give biggest bang for buck, Y-piece looks nice, tune resistor included wink, can do this in two goes (first manifold replacement, then Y-piece when the welded crack on it finally gives in)
Cons: std manifolds don't look so nice & may leak again - next week or in 15 years, who knows?

  • ACT 'performance' manifolds & Y-piece package:


Pros: shiny, everything brand new & probably of higher grade stainless than the cheap TVR stuff, claimed 20 lbs.ft gain over standard, racing cats available should this ever become a requirement to get to my own house legally in my car (I live in a city centre).
Cons: best part of a grand; top end gain?

  • TVR Car Parts Chim/Griff manifolds including Y-piece:

Pros: as above; these have longer primary tubes than the ACT ones - better performance? Over £300 cheaper, too.
Cons: No evidence of engine dyno or rolling road tuning/validating in product description

spend

12,581 posts

282 months

Wednesday 25th March 2009
quotequote all
The precat ones are nice in that they have long primaries, but the tight bend around the front of the engine might be a disadvantage. TVR's big collector and nice big diameter around the bend is not as daft as it seems, but I suspect was more influenced by positioning the lambda sensor than anything else wink I'm yet to be convinced that there are significant advantages to either alternative when going into the y-piece?

I've got a good set of flanged manifolds Eric if you can convince Cliff to make a Y-piece with flanges, rather than the "Band-It" (c) contraptions. I know you're a stickler for originality hehe

clive f

7,259 posts

264 months

Wednesday 25th March 2009
quotequote all
900T-R said:
I know they're good value Clive, just not in relation to the value of the average Chim though... hehe If I could afford them, it would be a question of whether the dealer technician would be OK with changing the water pipe run and whatnot (all cars are different) and then I'd still reckon it would cost a fair bit more because of it being the 1st time they were installed over here - all of a sudden you're looking at £3K+ yikes
sorry mate, didn`t realise you were a johnny foriegnerhehe

spend

12,581 posts

282 months

Wednesday 25th March 2009
quotequote all
What!!!! I've heard you wear beret's and pedal round on onion garnished bikes anyway, on that damned Island evilhehe

900T-R

Original Poster:

20,406 posts

288 months

Wednesday 25th March 2009
quotequote all
Hey, at least the exchange rate works in my favour these days... wink

Hoover.

5,993 posts

273 months

Wednesday 25th March 2009
quotequote all
something wrong with my off the shelf system hehe ........ gets comments everywhere wink

ACT

2,529 posts

315 months

Friday 27th March 2009
quotequote all
900T-R said:
Right, options found so far.

  • SH std de-precat manifolds + this:


Pros: seems to give biggest bang for buck, Y-piece looks nice, tune resistor included wink, can do this in two goes (first manifold replacement, then Y-piece when the welded crack on it finally gives in)
Cons: std manifolds don't look so nice & may leak again - next week or in 15 years, who knows?

  • ACT 'performance' manifolds & Y-piece package:


Pros: shiny, everything brand new & probably of higher grade stainless than the cheap TVR stuff, claimed 20 lbs.ft gain over standard, racing cats available should this ever become a requirement to get to my own house legally in my car (I live in a city centre).
Cons: best part of a grand; top end gain?

  • TVR Car Parts Chim/Griff manifolds including Y-piece:

Pros: as above; these have longer primary tubes than the ACT ones - better performance? Over £300 cheaper, too.
Cons: No evidence of engine dyno or rolling road tuning/validating in product description
Your getting confused, the picture you show for ACT manifolds is infact V8S, nothing like our Griff/Chim manifolds

900T-R

Original Poster:

20,406 posts

288 months

Friday 27th March 2009
quotequote all
ACT said:
Your getting confused, the picture you show for ACT manifolds is infact V8S, nothing like our Griff/Chim manifolds
Ah, but that's the pic in your own manifolds web shop page shows for the Chim/Griff manifolds... (and yes I did notice that it said 'v8s' when I copied the URL) wink

Edited by 900T-R on Friday 27th March 19:25

LordGrover

34,191 posts

243 months

Friday 27th March 2009
quotequote all
I have the Peninsular stainless manifolds and Y-piece on my '92 Griff 430. They were put on by the previous owner so I can't say what improvement(s) it made on what it was before. But... it sounds great and shows good numbers if that's what you're looking for.
Being a bit of a knob though, I'm binning them this Spring in favour of V8 Enhancements 1.3/4" tuned manifolds - they look great, sound better and more grunt - no brainer really. There's a short video but it doesn't really do them justice: click.
I'm also having some other work done soon after to further enhance it so I'll be interested to see how it drives by the Summer.
Should be schmokin'! cool

900T-R

Original Poster:

20,406 posts

288 months

Friday 27th March 2009
quotequote all
Could I persuade you to part with your existing manifolds/Y-piece for some nice poundage if/when you proceed?

LordGrover

34,191 posts

243 months

Friday 27th March 2009
quotequote all
I'm afraid you can have second dibs only - someone else has got in before you. It's not till May so if he changes his mind I'll let you know.