Discussion
AntonyJ said:
Wont this depend on individual installations?
I.E what your min/max TPS values are?
yes your right but this gives me an idea what some values people are using, also how many have bothered to enable this feature. My car was setup at Emerald and they didnt set this feature, not sure why thoughI.E what your min/max TPS values are?
Hi Nigel!
You want the rpm setting to around 2k but you can lower it a tad if you find you're getting a slight bump as it passes through 2k. The 'throttle pot' setting will depend entirely on your own throttle pot setup. It needs to tell the ECU when you're off the gas completely though with potentiometers, the resistance (and therefore number recorded by the ECU) can vary depending on heat/wear over time etc). To stop this causing a problem, you put in a number slightly more than the minimum value recorded to keep the ECU in idle or overrun fuel cut even if the reading isn't absolute minimum. It could be anything from 30 to 200 (mine is around 50 IIRC) depending on the base resistance of your throttle pot. What you want to do is re-calibrate your throttle in the setup dropdown menu (don't push your throttle pedal very hard though or it will bias the throttle load sites toward the top end of the range). You want to press it gently into the stop and release. When this is done, there is an option to give an offset number to your idle and overrun fuel cut modes as well as saving the new figures; this basically takes the minimum throttle pot number (which can be viewed in the diagnostic data page found in the help dropdown menu), and adds a number you choose to it, then saves it on all of your maps, thereby adding the slight offset you seek. My numbers vary from around 50 to 800ish, and this difference of 750ish will be divided between the 16 or so load sites, so the numbers will move very quickly with minimal pedal travel. This means that you could put in a fairly large number and it would have little effect, but to stop it creating a slight deadspot by impinging on load site number 1, you want to add a smallish number. I go for 5 on each. You can test this by going into the diag data page and looking at the number with your foot off the throttle. Next, press it down to max and release a few times. Note what it returns to as this will likely vary by 2-3 points (or more if anything is sticking). Make sure your offset will cover this variation - if it is big, perhaps give your throttle cable and assembly a good greasing - my car was losing throttle response purely because it wasn't sliding easily enough (on a brand new cable!).
Anyway that should get you set up correctly. Another neat trick if you want pops and bangs with a little bit of right foot as with the standard system is to increase the offset to about 10, and retard ignition and fuel to around 5 on 0 throttle all the way from 1500 to 6000. With this in place, as you flick the ECU in and out of fuel cut mode by touching the throttle very lightly (as with the standard system), it will chuck in the odd retarded spark and tiny bit of fuel which will cause pops and bangs as before. Or of course set up another identical map, one with fuel cut on and one with it off. One will pop all the time like a Cerb, the other will never pop unless you want it to
Oh another quick thing to add... If you have adaptive fueling enabled, either leave overrun fuel cut disabled, or do not allow adaptive fueling on zero throttle or the ECU will get confused and keep adding fuel on zero throttle as nothing is coming out due to fuel cut mode!
Hope that helps
Oh, and I do use fuel cut on my normal adaptive fuel map, but have a pops and bangs noisy bugger still with adaptive fuelling map and a 'as it left Austec in open loop' mode in case I, or the lambda sensor cocks anything up on the first two maps...
You want the rpm setting to around 2k but you can lower it a tad if you find you're getting a slight bump as it passes through 2k. The 'throttle pot' setting will depend entirely on your own throttle pot setup. It needs to tell the ECU when you're off the gas completely though with potentiometers, the resistance (and therefore number recorded by the ECU) can vary depending on heat/wear over time etc). To stop this causing a problem, you put in a number slightly more than the minimum value recorded to keep the ECU in idle or overrun fuel cut even if the reading isn't absolute minimum. It could be anything from 30 to 200 (mine is around 50 IIRC) depending on the base resistance of your throttle pot. What you want to do is re-calibrate your throttle in the setup dropdown menu (don't push your throttle pedal very hard though or it will bias the throttle load sites toward the top end of the range). You want to press it gently into the stop and release. When this is done, there is an option to give an offset number to your idle and overrun fuel cut modes as well as saving the new figures; this basically takes the minimum throttle pot number (which can be viewed in the diagnostic data page found in the help dropdown menu), and adds a number you choose to it, then saves it on all of your maps, thereby adding the slight offset you seek. My numbers vary from around 50 to 800ish, and this difference of 750ish will be divided between the 16 or so load sites, so the numbers will move very quickly with minimal pedal travel. This means that you could put in a fairly large number and it would have little effect, but to stop it creating a slight deadspot by impinging on load site number 1, you want to add a smallish number. I go for 5 on each. You can test this by going into the diag data page and looking at the number with your foot off the throttle. Next, press it down to max and release a few times. Note what it returns to as this will likely vary by 2-3 points (or more if anything is sticking). Make sure your offset will cover this variation - if it is big, perhaps give your throttle cable and assembly a good greasing - my car was losing throttle response purely because it wasn't sliding easily enough (on a brand new cable!).
Anyway that should get you set up correctly. Another neat trick if you want pops and bangs with a little bit of right foot as with the standard system is to increase the offset to about 10, and retard ignition and fuel to around 5 on 0 throttle all the way from 1500 to 6000. With this in place, as you flick the ECU in and out of fuel cut mode by touching the throttle very lightly (as with the standard system), it will chuck in the odd retarded spark and tiny bit of fuel which will cause pops and bangs as before. Or of course set up another identical map, one with fuel cut on and one with it off. One will pop all the time like a Cerb, the other will never pop unless you want it to

Oh another quick thing to add... If you have adaptive fueling enabled, either leave overrun fuel cut disabled, or do not allow adaptive fueling on zero throttle or the ECU will get confused and keep adding fuel on zero throttle as nothing is coming out due to fuel cut mode!
Hope that helps

Oh, and I do use fuel cut on my normal adaptive fuel map, but have a pops and bangs noisy bugger still with adaptive fuelling map and a 'as it left Austec in open loop' mode in case I, or the lambda sensor cocks anything up on the first two maps...
Edited by 450Nick on Monday 23 March 22:53
cheers for that Nick !! I took the car for a spin and found it popping and banging and I was sure it wasnt doing this prior to the winter layup, What i have found is Emerald made my running map No1, created another map for MOT which is map No 3, I disconnected the selector switch, the ECU was set to less than 1.3v use map No1, howvever with the selector switch unplugged the live input voltage goes to 5v selecting map no3. Its this map no3 thats making the pops etc, what good does using the fuel over run do to the running of the car ? as i mentioned earlier not sure why Emerald didnt set this function on.
Now to fit the Dynojet lambda and see what the fuelling is doing
Now to fit the Dynojet lambda and see what the fuelling is doing
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


