Wot No Trumpet Base Gasket?!?
Wot No Trumpet Base Gasket?!?
Author
Discussion

debaron

Original Poster:

878 posts

228 months

Monday 23rd March 2009
quotequote all

Just pulled the trumpet base off and was expecting to find a gasket of some sort. Nothing - Not even residue of old gasket sealant!

What's the correct procedure for re-fitting - Best off using a cork one or metal one? Or will gasket in a tube do?


Cheers,



Ryan

Mr Haribo

318 posts

220 months

Monday 23rd March 2009
quotequote all
They are all held together with a sealant, all rovers ect were done the same.
You can buy a gasket from sc power !

Ballistic Banana

14,706 posts

298 months

Monday 23rd March 2009
quotequote all
hymolar blue is what a majority use IIRC

BB

daz the plumber

14,997 posts

262 months

Monday 23rd March 2009
quotequote all
i have a insulator or spacer fitted , been told it cools the air down , thus giving more power , don`t know if this gizmo works !

That Daddy

19,464 posts

252 months

Monday 23rd March 2009
quotequote all
Mr Haribo said:
They are all held together with a sealant, all rovers ect were done the same.
You can buy a gasket from sc power !
That gasket as similar benefits to a full insulator cheap too wink

spend

12,581 posts

282 months

Monday 23rd March 2009
quotequote all
"Cooling it" and "stopping it getting hot" are actually very different things IMHO.

I still suspect some of the claimed benefits maybe exacerbated by short bursts on Rolling Roads. At steady state the insulator is just keeping heat in the manifold, so there is actually less external surface to dissipate the latent the heat?

debaron

Original Poster:

878 posts

228 months

Monday 23rd March 2009
quotequote all


Thanks everyone - think I'm gonna get the gasket and spacer set and cut down my trumpets by 25mm.


That Daddy

19,464 posts

252 months

Monday 23rd March 2009
quotequote all
Sounds good Debaron,i was only speaking to my brother about the heat issues of the plenum the other day and as he found out when under large throttle openings even on a hot day the plenum does not get hot anyway in fact barely warm down to the cold air rushing through its gullet,but at low throttle openings and town use that plenum gets flipping HOT and its that hot air that's going to consumed when you 1st hit the loud pedal and want to play eek you i going the right way with your plans wink remember though that when you fit the plenum spacer you are unshrouding the trumpets from the plenum ceiling anyways so your shortning the trumpets will have less benefit than to a unspaced plenum IMHO wink

Edited by That Daddy on Monday 23 March 22:48

slideways

4,101 posts

252 months

Monday 23rd March 2009
quotequote all
That Daddy said:
Mr Haribo said:
They are all held together with a sealant, all rovers ect were done the same.
You can buy a gasket from sc power !
That gasket as similar benefits to a full insulator cheap too wink
any idea if this insulator is suitable for a 45mm inlet manifold orjust for standard also i heard somewhere than the stuff plastic chopping boards are made from can be used as an insulator is this true??
Rich

That Daddy

19,464 posts

252 months

Monday 23rd March 2009
quotequote all
slideways said:
That Daddy said:
Mr Haribo said:
They are all held together with a sealant, all rovers ect were done the same.
You can buy a gasket from sc power !
That gasket as similar benefits to a full insulator cheap too wink
any idea if this insulator is suitable for a 45mm inlet manifold orjust for standard also i heard somewhere than the stuff plastic chopping boards are made from can be used as an insulator is this true??
Rich
I think the Magnaparva one was made from some kind of nylon material like a cutting board laugh cant comment on the 45mm thing i am only going with this research myself at the moment frown i did see this though http://cgi.ebay.co.uk/ROVER-V8-ENGINE-45MM-EFI-THE... read the note at the bottom of the listing Slideways wink

Edited by That Daddy on Monday 23 March 23:07

slideways

4,101 posts

252 months

Monday 23rd March 2009
quotequote all
That Daddy said:
slideways said:
That Daddy said:
Mr Haribo said:
They are all held together with a sealant, all rovers ect were done the same.
You can buy a gasket from sc power !
That gasket as similar benefits to a full insulator cheap too wink
any idea if this insulator is suitable for a 45mm inlet manifold orjust for standard also i heard somewhere than the stuff plastic chopping boards are made from can be used as an insulator is this true??
Rich
I think the Magnaparva one was made from some kind of nylon material like a cutting board laugh cant comment on the 45mm thing i am only going with this research myself at the moment frown i did see this though http://cgi.ebay.co.uk/ROVER-V8-ENGINE-45MM-EFI-THE... read the note at the bottom of the listing Slideways wink

Edited by That Daddy on Monday 23 March 23:07
scratchchin mmm if your refering to the answer to the guys question, it sounds like he knows his stuff wink

That Daddy

19,464 posts

252 months

Monday 23rd March 2009
quotequote all
Yes,i have been looking at some of the stuff he does for a while now,its gonna be V8 developments for the Camshaft kit though wink

GreenV8S

31,027 posts

315 months

Monday 23rd March 2009
quotequote all
That Daddy said:
I think the Magnaparva one was made from some kind of nylon material like a cutting board laugh
I thought it was phenolic sheet. That's ideal because it has very good insulation properties and virtually identical thermal expansion properties to aluminium.

That Daddy

19,464 posts

252 months

Monday 23rd March 2009
quotequote all
GreenV8S said:
That Daddy said:
I think the Magnaparva one was made from some kind of nylon material like a cutting board laugh
I thought it was phenolic sheet. That's ideal because it has very good insulation properties and virtually identical thermal expansion properties to aluminium.
Never had one in my grubby mitts so thanks for the info thumbup

spend

12,581 posts

282 months

Tuesday 24th March 2009
quotequote all
Several insulators I've seen are made from Carp Tufnol, just ring round your local plastic sheet wholesalers for a suitable offcut. A few saws, drills and a couple of hours later you have one for a few pounds outlay.