Lambda waveforms
Discussion
I have been getting pretty rubbish mileage on my 1998 400, usually get about 18MPG, this is when driving pretty gently as well, clearly something is not quite right.
I am slowly going through the injection system & checking for faults.
I have had a storage scope on the Lambda outputs & was hoping someone might be able to confirm they are operating as expected.
At idle I get a roughly square wave from 0.1 to 1.2 V, the voltage switches every 5 seconds, I get the same from both sensors.
At 2200 RPM pretty much the same but the voltage switches every 1 second or so.
The lambda probes were changed about 3 years and 15000 miles ago so should be ok.
Out of interest I put a new sensor that I got from Global automotive in the states via ebay in, this showed the same voltage levels, but only switched state a half the rate of the old sensors.
If anyone here has any comments I would be most gratefull.
Andy
I am slowly going through the injection system & checking for faults.
I have had a storage scope on the Lambda outputs & was hoping someone might be able to confirm they are operating as expected.
At idle I get a roughly square wave from 0.1 to 1.2 V, the voltage switches every 5 seconds, I get the same from both sensors.
At 2200 RPM pretty much the same but the voltage switches every 1 second or so.
The lambda probes were changed about 3 years and 15000 miles ago so should be ok.
Out of interest I put a new sensor that I got from Global automotive in the states via ebay in, this showed the same voltage levels, but only switched state a half the rate of the old sensors.
If anyone here has any comments I would be most gratefull.
Andy
A freind of mine has a 5ltr Griff, and that switches at about 1 to 2.5 second intervals that is slow as my 3.9 constantly switches around 1 seconds at idle. I went through the car with a fine tooth comb and cant find a reason. The only possibility Ive found so far is a possible pre cat problem of some sort, as these are before the sensors and alter the ECU correction cycle. My car has no cats at all and a couple of 4.5 ltrs cars Ive looked at run at the same rate as mine. Have you checked the voltage setting on the AFM, as Mark Adams says this effects the mixture on the cat map ? (The amount of correction the ecu has to do). Ive not seen any change myself but its worth checking. Also check the timing as this alters the lambda outputs. Its possibe the ECU is correcting as it should below 3400 rpm, but the car is running rich above this when its open loop, and it will simply exceed the measurement of the probes, that peak out at about 1.2 volts, so you dont know who rich it is. Also mis-fires show up as a lean mixture, and the ECU can over compensate and put to much fuel in. A session on the rollers will tell you for sure.
Was hoping you might comment... I have waved a voltmeter over the AFM & it all seems fine according to Mark Adams tests.
The timing I have checked & adjusted, but until I get a DTI down the plug hole on cyl1 I cant be 100% certain it is bang on, DTI is on it's way from ebay as we type.
It might be worth mentioning that the pre cats have been removed.
I had it on a rolling road a couple of weeks ago, the AFR above 3400 rpm was fairly level between 11.5 and 12.0
From 2000 to 3400 rpm the AFR was fairly steady between 12.5 & 11.5.
The car drives & runs very well with no signs of any issues, on the rollers it made 229 BHP at 5700 rpm
I have had a fuel pressure gauge on the fuel rail & it is showing around 25 - 30 PSI which is possibly somewhat low.
It just peeves me that it is drinking too much juice & that as yet I can't find out why!
Andy
In closed loop the A:F should be nearer 14.5;1, and open loop I think the optimum power is around 12.5: Its odd that closed loop shows so rich, as the whole point of the lambda probe is the switch point is 14.5:1 or so. The ECU waits for a switch point to occur to say lean, and then applies an "offset" to try and make it switch "rich". If the lambda switch does not occur, then the offset is increased and applied again, and repeated until the switch occurs. The process then repeats the other way. This is why you see a constantly variable amount of swing on the voltages, and some inconsistent timing values as the exhaust oxygen content will alter with the actual combustion burn, and hence the correction offset required. I wonder if a slow response is due to the systems inabilty to correct the mixture with just a couple of offsets applied, so the changes get bigger and bigger until it overshoots far to rich (?) This whole system is controlled by the ECU constantly changing the injector timing, which can be altered per engine cycle. I guess poor injector performance could be a problem, but I have no first hand experiance of this. It would be worth checking all the plugs are the same colour, as leaky injectors should show up as rich on a plug by plug basis. Ill keep thinking!
blitzracing said:
I wonder if a slow response is due to the systems inabilty to correct the mixture with just a couple of offsets applied, so the changes get bigger and bigger until it overshoots far to rich (?)
Whilst I had the scope connected there were a couple of times when the Lambda output voltage just sat either high or low, presumably this is because the whole control loop has saturated one way or the other? a quick blip on the throttle would get things back to normal, but if this is happening a lot maybe this would explain why I am using so much extra fuel. I will have to rig up a LED bargraph monitor in the car I see what happens whilst driving maybe.The AF ratio from the rolling road would just have been open loop as the throttle was wide open all the time..
Andy
lotusandy said:
blitzracing said:
I wonder if a slow response is due to the systems inabilty to correct the mixture with just a couple of offsets applied, so the changes get bigger and bigger until it overshoots far to rich (?)
Whilst I had the scope connected there were a couple of times when the Lambda output voltage just sat either high or low, presumably this is because the whole control loop has saturated one way or the other? a quick blip on the throttle would get things back to normal, but if this is happening a lot maybe this would explain why I am using so much extra fuel. I will have to rig up a LED bargraph monitor in the car I see what happens whilst driving maybe.The AF ratio from the rolling road would just have been open loop as the throttle was wide open all the time..
Andy
Hey Blitz , what you said just struck a chord with me. I dont pretend to understand all the 'lektrical' stuff but I've been experiencing problems with pick-up and when I snap open the throttle( from under the bonnet) there's a noticeable delay and lots of sucking noise before the engine picks up . I've tried it only opening partially and it still has a noticeable delay. D'you think it could be sticky counterbalance weights or maybe insufficient vac to the dizzy? i think I should say that due to changing various bits I'm now getting a genuine 280 miles from 53 litres of shell ( 84 miles a day mixed driving )and my shunting has all but dissappeared so I'm not thinking Lambdas.
Nick................
Nick................
Edited by f@-pots on Thursday 2nd April 12:30
Gassing Station | Chimaera | Top of Page | What's New | My Stuff




