Timing figures
Timing figures
Author
Discussion

f@-pots

Original Poster:

204 posts

234 months

Wednesday 1st April 2009
quotequote all
Timed her at the prescribed 8 degrees BTDC and she felt marginally worse ,less get up and go etc. Tried again at 10 DBTDC and she felt much better . Is it worth going to eleven or am I as far as I can go?


Nick...........

Chimjunkie

2,879 posts

242 months

Wednesday 1st April 2009
quotequote all
Dont assume the markings on the crank pulley are correct! Many have slipped and thus you need to re-establish TDC.

f@-pots

Original Poster:

204 posts

234 months

Thursday 2nd April 2009
quotequote all
OK Chimjunkie , will do........

Nick............

WokingWedger

1,030 posts

236 months

Thursday 2nd April 2009
quotequote all
Okay, I am running slightly behind Nick here.

I have found 1 timing mark and one side of it its marked 'after'. I presume this means that side of the mark is 'after' TDC. I can not see any other marks, so how do I know where 8 to 12 deg is. Or do I need a linear measurement around the circumference.

I can see the 'cut out' in the damper ( I assume this piece is a mass damper)about 1.5 inches around on the oppsite side to 'after'.
I have been warned that this is not a timing mark, so should there be more marks before this or after this ?

Any help much appreceiated.

Edited by WokingWedger on Thursday 2nd April 09:10

f@-pots

Original Poster:

204 posts

234 months

Thursday 2nd April 2009
quotequote all
OK, If you've found the cut out ,fairly near there will be the timing marks. Unfortunately they are only etched on the surface so are difficult to see. I did mine last night and had to first give the area a quick clean with some scotch brite and then clean off with some thinners. When you've done that you may need a torch or light source to see the marks. I could see 8 and 12 with a gradient in divisions of two so you may have to count back to get TDC (Mine was covered in sno-pake). As I said , I set mine to eight and got a pile of pooh so tried 'ten' and had much better results.
The accuracy of the timing marks could be called into question as has been suggested if the damper wheel is not in its correct position on the crank ie if it's slipped a bit.

Best of luck Nick.................

WokingWedger

1,030 posts

236 months

Thursday 2nd April 2009
quotequote all
So are the smaller 'degrees advance' marks between the 1 big mark that I can see and the cut out. If the diameter is approx 6 in (from memory) then 10 degress would be about half an inch away.

I shall clean this area to see what I can see

Edited by WokingWedger on Thursday 2nd April 12:16

rev-erend

21,624 posts

315 months

Thursday 2nd April 2009
quotequote all
Pete,

Here's a piture of the crank pulley ..

As you can see - the TDC is the red line in the centre and to the left is after and right is before..



If you are around tonight - I could pop round to you place with a degree marker template and show you how to makk it .. just email me your phone number if you want to do this.

WokingWedger

1,030 posts

236 months

Thursday 2nd April 2009
quotequote all
Thanks Alan, cant see the picture at work (stupid net nanny thingy)

Cant make tonight, but appreciate the offer

Be in touch soon

rev-erend

21,624 posts

315 months

Thursday 2nd April 2009
quotequote all
OK - I'm away for a week from tomorow .. so if you want me to show you now it's done then just drop me you number and I'll give you a call in a week and arrange a time to suit.