window to roof seal
Discussion
I probably should have asked this before the weather improved, however.......
There is a small gap between the top of the drivers window and the seal along the edge of the roof. The seal looks pretty manky and its been like it since I bought the car. Chimaera Mk 1 1995.
I seem to recall that there were two types of seal, one was a glued rubber seal (which I have) and apparently a better solution using a seal in a metal retainer strip. Doe anyone know if the later version can be fitted to the earlier cars, and where I could get the bits from?
Thnaks
Konrod
There is a small gap between the top of the drivers window and the seal along the edge of the roof. The seal looks pretty manky and its been like it since I bought the car. Chimaera Mk 1 1995.
I seem to recall that there were two types of seal, one was a glued rubber seal (which I have) and apparently a better solution using a seal in a metal retainer strip. Doe anyone know if the later version can be fitted to the earlier cars, and where I could get the bits from?
Thnaks
Konrod
Hi ,
It is possible to fit the mark II seal
You need to buy the Targa Seal Rail , Spacer and MKII Seal.
You then need to cut the rail and spacer to size and then self tapper it into the Targa top and then slide the rubber seal into the rail.
I found as recommended on here that spraying the rubber seal with Hair spray made the seal slide in easy , Then it's just a matter of cutting the seal to suit .
The MKII seal is a lot better than the MKI seal in my view.
I purchased all the parts from www.TVRShop.com
It is possible to fit the mark II seal
You need to buy the Targa Seal Rail , Spacer and MKII Seal.
You then need to cut the rail and spacer to size and then self tapper it into the Targa top and then slide the rubber seal into the rail.
I found as recommended on here that spraying the rubber seal with Hair spray made the seal slide in easy , Then it's just a matter of cutting the seal to suit .
The MKII seal is a lot better than the MKI seal in my view.
I purchased all the parts from www.TVRShop.com
Hi all - need some ideas here.
I replaced the seals with the updated (Mk2) type yesterday. Easy job once I had the correct screws and it is a much neater result than the glued seals. Problem is that I still have the gap (can be either side as there is a bit of play in the roof position).
I have never found the stop height aduster - is it in the inside or outside of the glass, does the glass have to be up or down to see it (and if its on the inside and the galss has to be up, how do you get to it as the glass angles inwards??)
I know its not a major issue, but its bugging me as I've managed to fix all of the other long term niggles (heater direction, mirrors etc.).
Thanks in advance
I replaced the seals with the updated (Mk2) type yesterday. Easy job once I had the correct screws and it is a much neater result than the glued seals. Problem is that I still have the gap (can be either side as there is a bit of play in the roof position).
I have never found the stop height aduster - is it in the inside or outside of the glass, does the glass have to be up or down to see it (and if its on the inside and the galss has to be up, how do you get to it as the glass angles inwards??)
I know its not a major issue, but its bugging me as I've managed to fix all of the other long term niggles (heater direction, mirrors etc.).
Thanks in advance
Konrod, I've had the exact same issue in the past. As mentioned you can raise the glass by ~5mm I think, though having never done this I assume it will raise the glass along the whole length of the window which may or may not be helpful depending on the size of the gap. If you have Steve Heath's bible he explains where it is and how to adjust it.
HRG makes a good point about filling out the seal itself. The center of the seal is hollow and you can feed something like a thin plastic tube along the length of the seal to pad it out.
In my case I had a small gap on the driver's side, but only at the front of the window towards the windscreen end. I found when I recovered my targa panel that there were additional washers between the roof panel and the spacer bar to help counter the window gaps, except where the current gap was. I posted a picture on here ages ago, I'll see if I can dig it out.
So it's possible to pad out the gap between the window and seal by adding additional spacers behind the long spacer bar. This means you'll be closing the gap by creating another one at the point where the spacers meet the roof. This gap can then be filled with a silicon sealant like silkaflex (sp?).
ETA: Link
HRG makes a good point about filling out the seal itself. The center of the seal is hollow and you can feed something like a thin plastic tube along the length of the seal to pad it out.
In my case I had a small gap on the driver's side, but only at the front of the window towards the windscreen end. I found when I recovered my targa panel that there were additional washers between the roof panel and the spacer bar to help counter the window gaps, except where the current gap was. I posted a picture on here ages ago, I'll see if I can dig it out.
So it's possible to pad out the gap between the window and seal by adding additional spacers behind the long spacer bar. This means you'll be closing the gap by creating another one at the point where the spacers meet the roof. This gap can then be filled with a silicon sealant like silkaflex (sp?).
ETA: Link
Edited by GJR on Saturday 11th April 12:35
Bit of a thread resurrection here, but the seal on my hood looks a lot different to the ones that TVR Shop are selling, does anyone have a close up pic of the arrangement on their car with the window fitting against the seal?
I want to look and get it right because £50 seems a lot for a metal rail and some rubber?
I want to look and get it right because £50 seems a lot for a metal rail and some rubber?
Hi Lewis
Yours will look diffeent if it's a Mk1 (as per your profile pic). These had a rubber section (looks like a flat "Q" shape) glued to the edge of the targa top to meet the windows.
The Mk2 seal does work, but mine needed additional spacer strips (made of cut down plastic gutter left over from the splitter
), and the alignment of the rail is crucial to make sure that the glass meets the new rubber section. Try the targa with no seal and see where the glass comes to vs the edge lip of the targa panel.
HTH
J
Yours will look diffeent if it's a Mk1 (as per your profile pic). These had a rubber section (looks like a flat "Q" shape) glued to the edge of the targa top to meet the windows.
The Mk2 seal does work, but mine needed additional spacer strips (made of cut down plastic gutter left over from the splitter
), and the alignment of the rail is crucial to make sure that the glass meets the new rubber section. Try the targa with no seal and see where the glass comes to vs the edge lip of the targa panel. HTH
J
I have the MK2 kit already(not by me)but found when i re trimmed the roof that there are 2 different styles of that top seal,one is wider than the other,the ones i have fitted barely cover the top edge of the glass on either side,on my brothers car (mk2 seal also)he as the same style of seal but the piece that flares away from the location groove and onto the edge of the glass is wider by about 7mm and its these ones i need to get,just a heads up really,the ones i have fitted was supplied by a known specialist but frankly are not the same as the perished ones i removed(the wider type)and are coming off shortly 

Mr Nordic said:
Lewis,
I am with you, I want to do the Mk11 mod but dont want to pay £50 for 2 metal strips and spacers, I have trwled the net but cannot find any extrusion for real money.
Are you going next week?
Mr N
Unfortunately not I am with you, I want to do the Mk11 mod but dont want to pay £50 for 2 metal strips and spacers, I have trwled the net but cannot find any extrusion for real money.
Are you going next week?
Mr N

The car will not be ready by then, there has been a delay with the flywheel and its going to be off the road for the next few weeks. Its gutting

When its back on the road though i will make sure i come along to the next Mid Essex to catch up!
Simon Says said:
I have the MK2 kit already(not by me)but found when i re trimmed the roof that there are 2 different styles of that top seal,one is wider than the other,the ones i have fitted barely cover the top edge of the glass on either side,on my brothers car (mk2 seal also)he as the same style of seal but the piece that flares away from the location groove and onto the edge of the glass is wider by about 7mm and its these ones i need to get,just a heads up really,the ones i have fitted was supplied by a known specialist but frankly are not the same as the perished ones i removed(the wider type)and are coming off shortly 
If you find them post up a link 

Mine are currently puffed out with a length of washer tube. Works well but I'd like a wider seal if it's available.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



