Fuel rail
Author
Discussion

Meatball

Original Poster:

1,638 posts

241 months

Monday 6th April 2009
quotequote all
Morning folks
Can anyone point me to the correct gauge to read fuel pressure from the fuel rail valve, im not 100% confident in the readings of my FSE jobbie so i would like to double check....ive been quoted over £200 by the local auto factor????? it cant cost anymore than £20 shirley.

Thanks

Jonny_b

82 posts

226 months

Monday 6th April 2009
quotequote all
Yeah the professional kits are expensive. I would either take it to a local garage and ask them to check it, or put in an in-line fuel pressure reader (see link) or look for a gauge that pushes onto the fuel rail - not sure what fittings you would need though. The land rover forums might be useful as I think the fuel rails are the same.

In-line
http://www.demon-tweeks.co.uk/products/ProductDeta...

Kit
http://www.sealeypower.com/item.asp?item_id=131760


GreenV8S

31,027 posts

315 months

Monday 6th April 2009
quotequote all
You can buy a cheap inline gauge for £20 or so, but you already have one from the sound of it. If you buy another cheap one, are you any more likely to believe it?

Jonny_b

82 posts

226 months

Monday 6th April 2009
quotequote all
Sorry, misread your original post. Try a garage or borrow/buy a more expensive kit.

spend

12,581 posts

282 months

Monday 6th April 2009
quotequote all
Get a vacuum gauge so you can see the difference between the 2 of them - thats the relative pressure wink

blitzracing

6,422 posts

251 months

Monday 6th April 2009
quotequote all
I’ve just spent a day on the same problem !. I was using the lambda probe outputs to see what the fuelling was doing, and you could quite clearly see the lambda voltage drop right down under maximum acceleration in open loop, so it was clear something was up. The problem is fuel pressure tests are normally static, so if for any reason the fuel pressure drops under full load you are none the wiser. I ended up making up some copper line to allow me to remove the pressure gauge, and simply lodge it under my wiper so I could see it under load. You then have to remove the vacuum pipe to the regulator (the engine will not run that well at low speed like this) and the pressure should remain rock solid at whatever you set it to at any load. If it varies, something is wrong- in my case I’m loosing 3psi, so I have a fuel restriction somewhere. It turns out that about 3 PSI is enough to make the engine run very lean, so the gauge accuracy is important if that’s all you have to go on. The best bet is simply put a test meter on the lambda probe outputs and make sure you have at least .8 to 1v volt under full load and acceleration (open loop.) You can go a bit higher by increasing the fuel pressure, but if you go to far the idle becomes unstable and fuel consumption will go up. Its difficult to be precise as the 12.5 A/F ratio for maximum power is right on the end of the lambda probes response curve, and the voltage changes are small for quite large mixture changes, but its much better than guessing! This way it does not matter what pressure the gauge reads, just make sure you can meet this fuelling criteria to prevent engine damage. Otherwise it’s a trip to the rollers for precise setting up and that would be £200 much better spent !

Meatball

Original Poster:

1,638 posts

241 months

Monday 6th April 2009
quotequote all
Thanks for your replys chaps i was only looking/hoping to find a cheap alternative

Blitz im having a very similar problem...
Ive fitted a LC 1 wide band sensor which seems to be working after a couple of grounding & calibration issues.
The wideband is reading that im running rich at idle and WOT. Im using 38PSI fuel pressure at idle according to my FSE thingy (with the vacuum pipe disconnected).
After spending a whole weekend fitting the wideband its now my mission to make sure the bloody thing reads accurately hehe untill i can get time on the rolling road


blitzracing

6,422 posts

251 months

Wednesday 8th April 2009
quotequote all
You can test the regulator on an air line with a gauge if you take it off the car, as it will open with air as just as well as petrol. The standard one does not shut properly however if you reduce the pressure slowly, it carries on "farting", but the opening point is quite obvious as the pressure rises.

Chassis 33

6,194 posts

313 months

Wednesday 8th April 2009
quotequote all
In the past I've run a fuel gauge in place of where that Schrader valve is on the drivers side of the fuel rail. If you unscrew the valve from the rail using the (IIRC) 13mm hex, the thread is the same as a the ones on the FSE fuel regulator, (again IIRC) 1/8"NPT.

I've used a gauge from the Demon Tweeks catalogue in the past that appeared to be accurate, couldn't tell you the make or model, sorry.

Regards
Iain