HOTexhaust manifold
HOTexhaust manifold
Author
Discussion

MARKS6900

Original Poster:

306 posts

233 months

Monday 6th April 2009
quotequote all
Hi, took my project chimaera for its first drive today to get the wheels alined and noticed that the off side exhaust manifold was very very hot infact it was nearly glowing red and that was after driving for a couple of miles, you could smell the fibreglass nearest the manifold, when you start the car you can hear the fuel pump but this keeps priming, you can smell fuel, and it sounds like running water at the engine but there are no leaks that i can see, it starts ok and ticks over at about 1k rpm, it drives ok but i have had the odd back fire, the near side manifold seams ok, any ideas, thank you.

bobfather

11,197 posts

286 months

Monday 6th April 2009
quotequote all
Most likely a blockage at the precat. I would suggest not driving it like this. Just take both manifolds off, remove the precats, job done and it'll pop and bang heaps better than it did before

MARKS6900

Original Poster:

306 posts

233 months

Monday 6th April 2009
quotequote all
Hi, is it possible to cut these out and reweld them up, thanks.

bobfather

11,197 posts

286 months

Monday 6th April 2009
quotequote all
MARKS6900 said:
Hi, is it possible to cut these out and reweld them up, thanks.
Are you thinking of leaving the manifolds on the car, doing the cut and weld it in situ?

MARKS6900

Original Poster:

306 posts

233 months

Monday 6th April 2009
quotequote all
Hi, no i do not think that would be possible, just had a look through some old bills that came with the car, the last owner replaced that manifold last year with one he soured, looks like he bought a duff s/h one.

daz the plumber

14,997 posts

262 months

Monday 6th April 2009
quotequote all
hi, how did you get on with the wheels and the alinment,ive removed my pre cats , i know the pitt falls so give me a ring and i can help you thanks .

GreenV8S

31,027 posts

315 months

Monday 6th April 2009
quotequote all
You don't need to cut the manifold open to remove the precats, just take a chisel to them from the end if they don't fall out on their own. It would be worth checking whether the glowing exhaust was because of a blockage or because of a misfire. Normally I'd guess blockage because you ought to have noticed a misfire, but the fuel pump running continuously is definitely wrong and makes me wonder what else is happening.

showcase

240 posts

245 months

Monday 6th April 2009
quotequote all
use a Long masonry bit to drill out the pre-cats then a long old screw-driver to help break it upsmash .
Its a pig of a job curse but worth it. ( bonnet off helps). I compleatly de-catted mine a few weeks ago + new y-piece. Its the best thing iv done in a long time. (Dont forget to hover all the debris up from inside the manafold when you finish).

mb450

429 posts

230 months

Tuesday 7th April 2009
quotequote all
Don't forget to wear a decent face mask there are some nasties in there

zippy500

1,883 posts

300 months

Tuesday 7th April 2009
quotequote all
This is an interesting thread. My Griff had a glowing 5 & 7 exhaust header. No weird symptons and had me puzzled. So all over the Winter I was thinking of what it could be and thought about removing the manifolds to remove the precats as a starting task. However, took it for its first season drive on Saturday for over an hour, get back and its not glowing anymore. A temporaty blockage? Who knows.

However the other things you mention are slightly concerning. No expert, but I would suggest that it's possibly overfuelling and investigate that first. Maybe remove a plug or 2 and see what colour they are on the tips.

MARKS6900

Original Poster:

306 posts

233 months

Tuesday 7th April 2009
quotequote all
Hi, do you leave the manifolds on the car and just remove the y piece, thanks.

daz the plumber

14,997 posts

262 months

Tuesday 7th April 2009
quotequote all
to remove the pre cats you need to take the manifolds off the engine ,be carefull ,if you snap a bolt then the head as to come off.the exhaust needs to be removed to get access to the one side and you can`t attack the bottom bolts from above.if you manage to get the manifolds off then its a cheisel and drill time to remove the precats .i would purchase the steal gaskets and remember to clean both the heads and manifold .i removed mine three times before success,my manifolds needed to be re skimmed .i allso used a mix of studs and bolts and don`t forget the nord lock washers .i used a compound called ultra copper designed for making up tiny gaps .good luck .

debaron

878 posts

228 months

Wednesday 8th April 2009
quotequote all
If the fuel pump keeps priming and you can hear/smell fuel leaking (but can't see any signs) and you are getting one red-hot cylinder/manifold then it would be my assumption that you have a leaking injector on that cylinder - resulting in severe overfueling.

They can leak - never heard about leaking so bad you can actually hear it eek but anything is possible with these nasty Lucas injectors!

A fault that bad would show up on a fault reader but may drive ok seeing as the lambda sensors would be lean fueling the rest of the bank to compensate.

If you have a voltmeter, BlitzRacing's post on Lambda Reading is here - 7th post down


http://www.pistonheads.com/gassing/topic.asp?h=0&a...



My advice - Read the Lambdas first - Then take out the plug of the cylinder on which this problem was occurring and inspect it. If you have overfueling, it should be black - VERY black! And very sooty.

Compare it to another plug on the same bank - note any difference.

It would be well worth getting the injectors out for testing. James @ Injectortune.co.uk will soon tell you if you have problems and clean them out nicely while they are there.


Let us know what you find!


MARKS6900

Original Poster:

306 posts

233 months

Wednesday 8th April 2009
quotequote all
I think i might of found one of the problems, the fuel pump running, i left the ignition on and checked for fuel leaking, found the rubber fuel pipe from fuel filter to metal fuel pipe was cracked and spraying fuel all over the exhaust, i do not think the fuel filter has ever been replaced looking at the condition of it, the clamp bolt was siezed solid, plus its not the best place to try and work, tvr service history as well, makes you wonder what else they've not done, just hope this stops the fuel pump, will then check lambda reading.

MARKS6900

Original Poster:

306 posts

233 months

Thursday 9th April 2009
quotequote all
Hi, fixed the fuel leak, what a pig of a job, no wonder the fuel filter has never been changed, the fuel pump is still clicking with ignition on, but engine not started, did lambda check, it read 2.3, then dropped to 1.9, so it can not be over fueling, so is it a blocked manifold, the heat seems to be more the lambda side of the pre cat, thanks.

MARKS6900

Original Poster:

306 posts

233 months

Thursday 9th April 2009
quotequote all
Took out all 8 spark plugs, no dirty sooty plugs, if the fuel regulater was at fault would that cause the pump to keep running, i have also swapped the 2 relays round near the battery for the fuel pump, made no difference.

showcase

240 posts

245 months

Thursday 9th April 2009
quotequote all
MARKS6900 said:
Hi, do you leave the manifolds on the car and just remove the y piece, thanks.
shoutThe manifolds can stay in place Mark !. You will need to loosen the exhaust system in order to free the y-piece. smash(It needs to pull forward a few inches and the engin bay does not allow this).
If you are interested in de-cating cheak out some of the many threds. If you try and take off the manifold you could break something and im not sure you would gain much even if you did remove them.thumbup

daz the plumber

14,997 posts

262 months

Thursday 9th April 2009
quotequote all
mark if i you need a fuel regulator give me a shout i have a spare one in full working order .