Bush replacement .. DIY or not?
Bush replacement .. DIY or not?
Author
Discussion

sapper

Original Poster:

1,134 posts

236 months

Thursday 16th April 2009
quotequote all
How much of a pain is it to change the bushes and shocks.
Im looking to replace all bushes and shocks at the same time. (Poly flex and Gaz classic probably.)

Once all are replaced I would be getting a full service and geo set up.

I have time on my hands and im not bad with spanners so is it worth taking on myself or leaving to the experts. Are there likley to be any pit falls.




crackedfinger

1,569 posts

260 months

Thursday 16th April 2009
quotequote all
It's easy enough, just time consuming and if you are like me you are bound to be tempted to clean up & paint parts as well ... which takes a lot more time!

The tricky bit is getting the outer sleeve out, once you get a few done it's plain sailing though. New bolts from SHPUB helps assembly too.

sapper

Original Poster:

1,134 posts

236 months

Thursday 16th April 2009
quotequote all
I was thinking of giving everything a lick of paint while i'm at it. how long did it take you? is a week long enough?

lewis_sharman

5,958 posts

222 months

Thursday 16th April 2009
quotequote all
Mine is all apart at the moment and i have currently got the bushes out of 4 of the wishbones. Getting everything apart took me roughly a day, but the bushes are a pain and ended up having to design my own tool to remove the outer sleeve (will post up on this in the near future wink ) Hopefully will get the rest out today, and then it will be off to the powdercoaters and have new polybushes to go in after. Mine overall will have taken about 3-4 weeks, but that includes faffing around trying to find out the best way to remove the bushes, and sending the bits off for powdercoating.

I would say it is possible to do in a week, but you will be knackered by the end of it.

I would also recommend getting the Steve Heath bolts before you start, as i sheared 2 bolts getting the wishbones off irked

Colin RedGriff

2,541 posts

288 months

Thursday 16th April 2009
quotequote all
Hi

I had all the wishbones shotblasted, zinc primed and powdercoated which brought them up like new - it took a week for them to turn those around. A lot easier though than trying to strip, and repaint.

Rob has designed this tool clicky for removing bushes which I found made the process much easier and I was able to do the rear carriers in situ on the car. It can also be used to press the new bushes fully in.

Fitting the poly bushes is quite fiddly, they need to be pressed fully in or you will struggle to refit the wishbones. They are a little bit wider than the standard ones as they are designed to work differently. So some of the tolerances are very tight, particularly the rear toe-in adjuster and front lower wishbone rear mount.



daz the plumber

14,997 posts

262 months

Thursday 16th April 2009
quotequote all
just purchased two front bottom wish bones, up rated tubular powder coated in black £216 delivered for the pair .half the normal price !

STEV8E

635 posts

240 months

Thursday 16th April 2009
quotequote all
daz the plumber said:
just purchased two front bottom wish bones, up rated tubular powder coated in black £216 delivered for the pair .half the normal price !
Tell us where then fella

sapper

Original Poster:

1,134 posts

236 months

Thursday 16th April 2009
quotequote all
lewis_sharman said:
Mine is all apart at the moment and i have currently got the bushes out of 4 of the wishbones. Getting everything apart took me roughly a day, but the bushes are a pain and ended up having to design my own tool to remove the outer sleeve (will post up on this in the near future wink ) Hopefully will get the rest out today, and then it will be off to the powdercoaters and have new polybushes to go in after. Mine overall will have taken about 3-4 weeks, but that includes faffing around trying to find out the best way to remove the bushes, and sending the bits off for powdercoating.

I would say it is possible to do in a week, but you will be knackered by the end of it.

I would also recommend getting the Steve Heath bolts before you start, as i sheared 2 bolts getting the wishbones off irked
Just ordered the kit from Steve.

Looks like mugs of tea will be dissapearing into the garage for a while

lewis_sharman

5,958 posts

222 months

Thursday 16th April 2009
quotequote all
Just got the last bushes out thumbup

Will be taking a trip to the powdercoaters in a minute after a quick cuppa.

With the correct tools it definately isn't too bad, ive done 4 wishbones in an hour and a half.

Just the hubs left to do!

sapper

Original Poster:

1,134 posts

236 months

Thursday 16th April 2009
quotequote all
lewis_sharman said:
Just got the last bushes out thumbup

Will be taking a trip to the powdercoaters in a minute after a quick cuppa.

With the correct tools it definately isn't too bad, ive done 4 wishbones in an hour and a half.

Just the hubs left to do!
Lewis when you say correct tools what do you mean?
Im looking at using a blowtorch to melt the old bushes' rubber to get them out.

scotty_d

6,795 posts

225 months

Thursday 16th April 2009
quotequote all
I did the full rear ones over the winter get a burner and make your self a drift, This method took no time at all did all of them in a few hours from removing to fitting new ones. painting wish bones is what took the time for me. there are other methods but this was best for me if you can get a burner

HRG

72,863 posts

270 months

Thursday 16th April 2009
quotequote all
sapper said:
lewis_sharman said:
Just got the last bushes out thumbup

Will be taking a trip to the powdercoaters in a minute after a quick cuppa.

With the correct tools it definately isn't too bad, ive done 4 wishbones in an hour and a half.

Just the hubs left to do!
Lewis when you say correct tools what do you mean?
Im looking at using a blowtorch to melt the old bushes' rubber to get them out.
clicky or you can do it the hard way wink

sapper

Original Poster:

1,134 posts

236 months

Thursday 16th April 2009
quotequote all
HRG said:
sapper said:
lewis_sharman said:
Just got the last bushes out thumbup

Will be taking a trip to the powdercoaters in a minute after a quick cuppa.

With the correct tools it definately isn't too bad, ive done 4 wishbones in an hour and a half.

Just the hubs left to do!
Lewis when you say correct tools what do you mean?
Im looking at using a blowtorch to melt the old bushes' rubber to get them out.
clicky or you can do it the hard way wink
looks like it'll be the hard way, I havent got one or access to a machine shop to make one.

HRG

72,863 posts

270 months

Thursday 16th April 2009
quotequote all
A small local machine shop should make you one for about £30-£40. Certainly makes the job easier but as said it's doable without smile