Low oil pressure
Low oil pressure
Author
Discussion

DJD

Original Poster:

66 posts

274 months

Friday 17th April 2009
quotequote all
Could do with some advise here about the above.

The car has had a top end rebuild and while it was being carried out the oil pump gears replaced. The car has since shown low oil pressure. The car is being serviced at the moment and we are trying to get to the bottom of the issue. The pressure before the work being carried out was around 35 rising to 45 when pushing on, now at idle it is around 0 rising to 15 at revs.

The indie has checked out the pressure relief valve and that's fine, what else could we be missing. I thinking that thicker oil should be our next port of call, the guy however want's to pull the engine and rebuild the bottom end also.

He has fitted a pressure gauge in the sender position and this comfirms the gauge readings in the car.

Is there any known issues with the oil pump? (serp engine). Would have thought with the work carried out that oil pressure would have improved slightly not fallen through the floor.

Simon Says

19,466 posts

252 months

Friday 17th April 2009
quotequote all
Have you checked the oil pump pick-up pipe for security and the strainer for blockage? did you drop the sump when this work was carried out to? if you have try another oil & filter change,have you made sure its not the electric gauge giving aggro(not the most reliable) get a workshop kit test done before pulling the motor to pieces wink

DJD

Original Poster:

66 posts

274 months

Friday 17th April 2009
quotequote all
Strainer has been cleaned out. Before all the other work was carried out there was a small leak coming from the sump so that was dropped and a new gasket fitted. The only other thing could be that the pick-up has come loose/has a split.

The pressure has been checked with a remote gauge in place of the electric gauge, this gave the same result.

Simon Says

19,466 posts

252 months

Friday 17th April 2009
quotequote all
Was the 2 bolts that secure the pick up pipe to the block checked for security?

spend

12,581 posts

282 months

Friday 17th April 2009
quotequote all
Piss poor oils that claim to be 20/50 fully synth can do that. Is the pressure dropping as soon as it gets warm...

DJD

Original Poster:

66 posts

274 months

Friday 17th April 2009
quotequote all
Hi spend

Yes the pressure does drop as soon as its warm. The garage doing the work is a TVR indie and I would have thought that the oils they use would be upto the job. Regarding the bolts, I can only assume they were secure.

I am thinking to ask him to drop the sump again check the oil pick up or replace and then fill up with Mobil 15/50 or some other top quailty oil. Small cost if the issue goes away, if not looks like it could be a bottom end rebuild.

Simon Says

19,466 posts

252 months

Friday 17th April 2009
quotequote all
Quinny said:
Don't assume the bolts are secure.

I did a sump gasket on a mates car on Tuesday, I undid the 2 bolts with my fingers (honest)

They came out as easy as pie, and we found this in the pic up pipe.



Your right about that Quinny,my brother resealed his sump(leaking from rear)and found one of the p/up bolts hanging out yikes fortunately the other was still tight,bet they both are now though laugh

Simon Says

19,466 posts

252 months

Friday 17th April 2009
quotequote all
Quinny said:
Loctite is your friendheheyes
Certainly is thumbup

DJD

Original Poster:

66 posts

274 months

Friday 17th April 2009
quotequote all
Cheers for all the input guys, will ask him to drop the sump and check this again. At the end of the day if this cures the issue then all well and good, if not its only a bit of labour and oil/filter. Small change if its something more serious.

Simon Says

19,466 posts

252 months

Friday 17th April 2009
quotequote all
DJD said:
Cheers for all the input guys, will ask him to drop the sump and check this again. At the end of the day if this cures the issue then all well and good, if not its only a bit of labour and oil/filter. Small change if its something more serious.
Sump change,one of the easier Tvr jobs for a change whistle

spend

12,581 posts

282 months

Friday 17th April 2009
quotequote all
Didn't Rob Rob once warn that some folks had used incorrect front cover gaskets on the intermediates that blocked the oil pickup? (since you mention having top end work)

DJD

Original Poster:

66 posts

274 months

Saturday 18th April 2009
quotequote all
I wish I was better placed to do a few of these type of jobs myself, however do not have enough room in the garage.

The gasket issue; spend, the guy working on the car has used all genuine L/R stuff. Was this issue poorly produced parts causing the blockage or are there differnet gaskets for the front cover. Its a big casting would not have thought too many changes were made to it during its production lifecycle.

I am not adverse to having the bottom end rebuilt, I just think that there is a very simple cause to this problem, all the things that I and your good selves have highlighted above. During a rebuild whatever is slightly amiss will be corrected and everything will be fine, and so over looked as the cause.

spend

12,581 posts

282 months

Saturday 18th April 2009
quotequote all
Sorry, don't know, can't recall clearly... just remember Rob mentioning something quite a while ago.. and its generally worth keeping his words in mind hehe

Not sure whether it was crap gaskets or incorrectly using P38 ones (oil pickup gallery is not used), so I always double check carefully the oil galleries on that gasket wink

Clutching at straws really, but it takes an awful lot of miles or something drastically wrong to lose so much pressure due to bottom end slop. Just seems more likely something to do with the top end work, co-incidence is quite rare IMHO I much prefer cause & effect hehe

WOO5IE

968 posts

228 months

Monday 20th April 2009
quotequote all
Do you get the oil red light on as this switches on at around 10lb or lower or is it just the gauge thats reading low

Woosi5

DJD

Original Poster:

66 posts

274 months

Monday 20th April 2009
quotequote all
No lights are lit, this is purely a reading from the gauge.

I have spoken to the guys doing the work today and he is going to drop the sump and look at the oil pick-up and strainer again before going any further forward.

WOO5IE

968 posts

228 months

Monday 20th April 2009
quotequote all
Hi Dave

Its strange that the oil pressure led is unlit. Any pressure below 10lbs and it should be lit. It is a dufferent sender unit for the LED, the guage has its own.
Does it come on when just turning the ignition on.

Woosi5

spend

12,581 posts

282 months

Monday 20th April 2009
quotequote all
WOO5IE said:
Any pressure below 10lbs and it should be lit.
The oil pressure switches are not reliable for calibration against the sender, IIRC there are something like 5, 8 & 10psi switch variants. Essential that they work - just do not rely on them to correlate to the gauge reading. Sounds like he has had the gauge checked using a proper test gauge anyway???...

VictorMeldrew

8,293 posts

308 months

Monday 20th April 2009
quotequote all
My 500 had a recurrent problem from new running cam followers. After the third set it went to TVR Power in Coventry and they found the oil pickup pipe hanging off, one bolt dropped out and the other hanging on by a thread. The pipe was swinging back and forth under acceleration and sucking fresh air half the time. Needless to say the bolts were loctited in place.