wont tick over
Discussion
Could be either a faulty stepper or air leak - effectively the same thing. If you have a faulty stepper then you have an uncontrolled air leak as opposed to a 'controlled' one when it is working.
Follow Blitzracing's excellent tips on stepper cleaning below:
1 - The pipe from the stepper to Plenum.
2 - The Plenum elbow from AFM.
3 - The carbon canister pipe. (1 inch hose on drivers side of Plenum - usually nearest front of car. The other is the brake servo so you'll soon know if you get the wrong one!)
4 - Poor seal around Plenum base
5 - Idle screw. Sometimes whistles if not set correctly. Not sure if this can cause a bad air leak but worth checking it isn't rattling around loose. Under a plastic plug on the Plenum somewhere. Have a search around on here. There are instructions on how to get at it.
HTH
Follow Blitzracing's excellent tips on stepper cleaning below:
blitzracing said:
1) Get the car warm
2) Remove the stepper from the plenum and reconnect it.
3) Hold the stepper in your hand, so you can catch the central cone and spring when it comes out.
4) Get someone to start the car. Without the stepper in place it will rev at around 2k- 2.5k (This is noisy!!), but the ECU will try to slow it down by powering the stepper motor and pushing cone outwards. It will do this in a series of pulses, a few seconds apart, until the cone and spring drop out. (assuming they are not completely stuck). It may take a bit of manual help to get the cone to fully release. Now stop the engine and let it cool.
6) Clean all the muck off the shaft, and lightly lubricate the screw thread inside the motor.
7) To reassemble, wind the shaft back into the motor so far, but align the slot in the shaft with the plastic keyway as best you can by rotating the shaft in its screw thread
8) With the engine cool, then reconnect the stepper motor. Power cycle the ignition on and off, (don't start) and the ECU will try to pull the shaft back in each time the ignition is turned OFF. This is the slightly tricky bit, as if the keyway and shaft are not quite aligned it wont pull home, so you may need a few attempts.
If the stepper is all ok then look/listen for air leaks in the engine bay. Try:2) Remove the stepper from the plenum and reconnect it.
3) Hold the stepper in your hand, so you can catch the central cone and spring when it comes out.
4) Get someone to start the car. Without the stepper in place it will rev at around 2k- 2.5k (This is noisy!!), but the ECU will try to slow it down by powering the stepper motor and pushing cone outwards. It will do this in a series of pulses, a few seconds apart, until the cone and spring drop out. (assuming they are not completely stuck). It may take a bit of manual help to get the cone to fully release. Now stop the engine and let it cool.
6) Clean all the muck off the shaft, and lightly lubricate the screw thread inside the motor.
7) To reassemble, wind the shaft back into the motor so far, but align the slot in the shaft with the plastic keyway as best you can by rotating the shaft in its screw thread
8) With the engine cool, then reconnect the stepper motor. Power cycle the ignition on and off, (don't start) and the ECU will try to pull the shaft back in each time the ignition is turned OFF. This is the slightly tricky bit, as if the keyway and shaft are not quite aligned it wont pull home, so you may need a few attempts.
1 - The pipe from the stepper to Plenum.
2 - The Plenum elbow from AFM.
3 - The carbon canister pipe. (1 inch hose on drivers side of Plenum - usually nearest front of car. The other is the brake servo so you'll soon know if you get the wrong one!)
4 - Poor seal around Plenum base
5 - Idle screw. Sometimes whistles if not set correctly. Not sure if this can cause a bad air leak but worth checking it isn't rattling around loose. Under a plastic plug on the Plenum somewhere. Have a search around on here. There are instructions on how to get at it.
HTH
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


