Can an injector completely stop injecting??
Can an injector completely stop injecting??
Author
Discussion

jonny_c

Original Poster:

170 posts

235 months

Saturday 18th April 2009
quotequote all
Started up last week to very slighly lumpy running and low power. As if i there was a cylinder off. A quick poke around revealed a bit of oil in the suppresion cap on cylinder 8, coupled with some green deposits in the distributer cap, and the exhaust manifold on that cylinder was running cool. Ah - i though - it's due a service, plugs, leads, arm and cap should sort it out with decent spark

Got the parts, messed about (found the vacuum advance unit hanging off distributor with a lost screw which is a very annoying non metric size so i've had to bodge it back on) got it going - runs fine but still somethings not right, even after a blast up the road - manifold still cool on cylinder 8.

Tested spark - blue and strong - Took out the plug, completly clean and no petrol smell, took out plug 7, nice brown colour as expected.

Diognosis seems a duff/blocked injector on cylinder 8?

The bible recommended steering clear of injector removal due to the high fuel pressure in the system - anyone any advice/experience on injector removal?

Seems my Nurburgring trip on Tuesday is a little ambitious.....

Simon Says

19,466 posts

252 months

Saturday 18th April 2009
quotequote all
If the car as been left standing then yes this can happen,i have had this happen with loads of second hand motors where the fuel rail that come with the engine as been left in place(yes even Hondas)try running the engine and giving the injector body a couple of sharp taps from a screwdriver,that's just taps though biggrin it seems to be the carbon/lacquer sometimes jams the mechanism,this as worked for me many times in the past wink got to be worth a go 1st thumbup

jonny_c

Original Poster:

170 posts

235 months

Saturday 18th April 2009
quotequote all
Thanks - nice tip!

Just tried it - used a large philips screwdriver and a socket extension to tap away.



Didn't work though!


Simon Says

19,466 posts

252 months

Saturday 18th April 2009
quotequote all
If you could borrow an old injector or borrow a noid light kit you can at least make sure its being switched,could save you a lot of head scratching,also while the engine is running get a long screwdriver and rest it on one of the working injectors and the handle end to your ear to get a feel for the clicking sound as the unit is being switched you can hear this through the screwdriver while the engine is running(stethoscope style)then try to do the same on the cylinder you think may have the dead injector,please keep the screwdriver away from rotating pulleys & HT leads while you carry out this test yikes good luck smile

Barkychoc

7,848 posts

235 months

Saturday 18th April 2009
quotequote all
The injectors are fired as 2 groups of 4 - 2,4,6 and 8 are fired at the same time so try swapping the connectors for 6 and 8 over and see if there's any difference to cylinder 8.
At least you can then rule out the electrics if it still isn't happening on No.8

jonny_c

Original Poster:

170 posts

235 months

Saturday 18th April 2009
quotequote all
Thanks Simon - tried to screwdriver as a stethoscope trick - I'm amazed at how much you can hear! - No dicernable difference between injectors though, just a mechanical rumble.....

I'd assumed there'd be some fireing sophitication so swapping cap wouldn't work! Anyway I couldn't easily get injector cap 8 to stretch to 6, but 6 went onto 8 no problem. Lost 6 - obviously, and could smell unburnt fuel in the exhaust gas, but still nothing from 8 - cold manifold pipe.....

There must be something up with the injector.

Anyone know if it's a Land Rover part? Would be nice to get one from a dealer on Monday morning.......

GreenV8S

31,027 posts

315 months

Sunday 19th April 2009
quotequote all
If you have an injector that seems to be staying closed, I suggest you test it with the engine off.

The injectors take 12V and make a very loud click when they open and close. By comparing the sound of the suspect injector with a known good one you can tell at once whether it has failed totally. (If it sounds OK that doesn't mean it's flowing properly, but it's a good start.)

Ideally get yourself a mini-power timer connector which you can buy for pence from most auto-electrical outlets, but if you don't have the correct connector you can still connect directly to the terminals with care.

Barkychoc

7,848 posts

235 months

Sunday 19th April 2009
quotequote all
Connectors if you want to get one --> http://www.vehicle-wiring-products.eu/VWP-onlinest...

Those angled boots part no 192152 look a far better idea for the injectors than the existing ones type 192150 they will allow the cables to drop down to the inlet manifold.

jonny_c

Original Poster:

170 posts

235 months

Sunday 19th April 2009
quotequote all
More goog advice! - I was afraid to try 12v direct incase they switched on a lower ECU voltage.

Just tried it - It's neigbour number 6 was definatly switching. 8 was dead - no reaction or sparking as i touched the terminals.

Tried the mulimeter across it - nothing again, number 6 showed a few ohms.


Good 'differential diagnosis' - just needs treatment!



I'll now got to resign myself to that fact that I'll have to go to Germany on my bike, unless I can talk everyone into putting it off for a week....... Pull the TVR reliability card!..... Though it is my fault for assuming it was a spark problem and leaving it too late.


Simon Says

19,466 posts

252 months

Sunday 19th April 2009
quotequote all
Jonny C it is a standard Rover part from the engines own era,sounds like you have a dead injector alright,it can happen with Bosch injectors(i have known it to)so just as possible with Lucas ones,its only a tightly wound coil of wire inside after all wink these cars are hardly in there 1st flush of youth wink

GreenV8S

31,027 posts

315 months

Sunday 19th April 2009
quotequote all
jonny_c said:
Tried the mulimeter across it - nothing again, number 6 showed a few ohms.
You should see around 15 Ohms resistance. When you say 'nothing' do you mean it showed open circuit (infinite resistance)? That sounds like a blown coil meaning new injector required. The standard ones aren't expensive, but beware of buying second hand. Since you have to remove the fuel rail to replace any of them, I suggest you take this opportunity to have *all* of them tested and serviced. No doubt the people who service them will have a good cheap source for replacements.

Simon Says

19,466 posts

252 months

Sunday 19th April 2009
quotequote all
GreenV8S said:
jonny_c said:
Tried the mulimeter across it - nothing again, number 6 showed a few ohms.
You should see around 15 Ohms resistance. When you say 'nothing' do you mean it showed open circuit (infinite resistance)? That sounds like a blown coil meaning new injector required. The standard ones aren't expensive, but beware of buying second hand. Since you have to remove the fuel rail to replace any of them, I suggest you take this opportunity to have *all* of them tested and serviced. No doubt the people who service them will have a good cheap source for replacements.
Could not have put it better myself biggrin

daz the plumber

14,997 posts

262 months

Sunday 19th April 2009
quotequote all
i used these £78 , came back with a computer read out and v8 developments were very pleased
http://cgi.ebay.co.uk/ULTRASONIC-FUEL-INJECTOR-CLE...

jonny_c

Original Poster:

170 posts

235 months

Monday 20th April 2009
quotequote all
My Multimeter is a cheap £5 model - so thinking about it it may have be 20ohms, with the resolution in 10 ohm intervals, well thats my excuse!

Stripped it all down last night - got a mate tracking down a Lucus injector now:

http://www.land-rover-parts-shop.com/shop/lrps/en/...

these guys have one in stock - ERR722 looks the same, except for the blue ring - mine have a green rings.

Anyone know any what thats all about?

GreenV8S

31,027 posts

315 months

Monday 20th April 2009
quotequote all
jonny_c said:
My Multimeter is a cheap £5 model - so thinking about it it may have be 20ohms, with the resolution in 10 ohm intervals, well thats my excuse!

Stripped it all down last night - got a mate tracking down a Lucus injector now:
It sounds as if the electrical test hasn't shown a fault then. So it's possible that the injector is stuck, which can happen due to deposits building up on the inside. Remember that whatever happened inside this injector has happened inside all the others too - I repeat my advice to get them all checked and serviced while they're out.

jonny_c

Original Poster:

170 posts

235 months

Tuesday 28th April 2009
quotequote all
Well - after an epic runaround on Monday I got a full set of injectors from another engine that was in someone's garage - they were all the same, Green bands and everything, and was assured the engine ran fine.

At 2 in the morning I finially finished changing them all, after carefully taking my time.

Set off to Germany at Mid-day - the engine ran perfect for the full trip. Should have reconditioned them while i had everything apart, like Peter said, but I didn't have the time!


Gratuitous 'ring pics:








Simon Says

19,466 posts

252 months

Wednesday 29th April 2009
quotequote all
Well done thumbup glad you made it.