AFM problem - Cold Start
Discussion
Hi all,
Changed my AFM for a shiny new one from eBay at around £60 as have been chasing slightly rough running for ages. There has been plenty of discussion on here about the quality of them and most people seem to say they work ok.
Anyway, the car does seem to run miles better with the new one on - Hooned up to London and back over the weekend so it has had a thorough test.
Engine revs a lot more freely up to 5000. Fuel economy is pretty good too.
The only thing is that when cold starting the tickover is all over the place for a few minutes. The ECU initially holds it high (1800 rpm) for a few secs an then it nearly dies (450 rpm) so the ECU compensates and then it goes high again for a few secs. This happens repeatedly but with the 'difference' between the high and low revs getting less and less as the engine warms. After a few minutes the engine idles perfectly.
It's not a Stepper Motor problem as the car cold-starts and idles fine with the old AFM on. And have also reset the ECU.
There is a adjustment screw on the new AFM which I believe is used for idle but I was under the impression that Cat'ed cars didn't pay attention to it.
Does anyone have any thoughts? Could my ECU be paying attention to the idle screw? (1996 400 Serp BTW)
Cheers
Ryan
Changed my AFM for a shiny new one from eBay at around £60 as have been chasing slightly rough running for ages. There has been plenty of discussion on here about the quality of them and most people seem to say they work ok.
Anyway, the car does seem to run miles better with the new one on - Hooned up to London and back over the weekend so it has had a thorough test.
Engine revs a lot more freely up to 5000. Fuel economy is pretty good too.
The only thing is that when cold starting the tickover is all over the place for a few minutes. The ECU initially holds it high (1800 rpm) for a few secs an then it nearly dies (450 rpm) so the ECU compensates and then it goes high again for a few secs. This happens repeatedly but with the 'difference' between the high and low revs getting less and less as the engine warms. After a few minutes the engine idles perfectly.
It's not a Stepper Motor problem as the car cold-starts and idles fine with the old AFM on. And have also reset the ECU.
There is a adjustment screw on the new AFM which I believe is used for idle but I was under the impression that Cat'ed cars didn't pay attention to it.
Does anyone have any thoughts? Could my ECU be paying attention to the idle screw? (1996 400 Serp BTW)
Cheers
Ryan
debaron said:
Hi all,
Changed my AFM for a shiny new one from eBay at around £60 as have been chasing slightly rough running for ages. There has been plenty of discussion on here about the quality of them and most people seem to say they work ok.
Anyway, the car does seem to run miles better with the new one on - Hooned up to London and back over the weekend so it has had a thorough test.
Engine revs a lot more freely up to 5000. Fuel economy is pretty good too.
The only thing is that when cold starting the tickover is all over the place for a few minutes. The ECU initially holds it high (1800 rpm) for a few secs an then it nearly dies (450 rpm) so the ECU compensates and then it goes high again for a few secs. This happens repeatedly but with the 'difference' between the high and low revs getting less and less as the engine warms. After a few minutes the engine idles perfectly.
It's not a Stepper Motor problem as the car cold-starts and idles fine with the old AFM on. And have also reset the ECU.
There is a adjustment screw on the new AFM which I believe is used for idle but I was under the impression that Cat'ed cars didn't pay attention to it.
Does anyone have any thoughts? Could my ECU be paying attention to the idle screw? (1996 400 Serp BTW)
Cheers
Ryan
I would advise you to check the volts at idle should be 1.8v then reset ecu after.Changed my AFM for a shiny new one from eBay at around £60 as have been chasing slightly rough running for ages. There has been plenty of discussion on here about the quality of them and most people seem to say they work ok.
Anyway, the car does seem to run miles better with the new one on - Hooned up to London and back over the weekend so it has had a thorough test.
Engine revs a lot more freely up to 5000. Fuel economy is pretty good too.
The only thing is that when cold starting the tickover is all over the place for a few minutes. The ECU initially holds it high (1800 rpm) for a few secs an then it nearly dies (450 rpm) so the ECU compensates and then it goes high again for a few secs. This happens repeatedly but with the 'difference' between the high and low revs getting less and less as the engine warms. After a few minutes the engine idles perfectly.
It's not a Stepper Motor problem as the car cold-starts and idles fine with the old AFM on. And have also reset the ECU.
There is a adjustment screw on the new AFM which I believe is used for idle but I was under the impression that Cat'ed cars didn't pay attention to it.
Does anyone have any thoughts? Could my ECU be paying attention to the idle screw? (1996 400 Serp BTW)
Cheers
Ryan
V8 Animal
Ive tweeked that CO trim screw untill im blue in the face, and I can get no change what so ever on the mixture on the catalyst fuel map. Having said that Mark Adams recommends the value be set to 1.8 volts (factory default) as it still alters a fueling offset internally, that the ECU will then compensate for when it gets some lambda feedback. So whatever this setting is it wont do any harm. What you need to do is put the old AFM back on the car and measure the AFM output at a stable idle. This will be around 1.5 -1.7 volts. Now replace it with the new one and repeat the process, and compare the voltages. They should be very near (say within 100mv). If the new one is different The ECU will be putting in more or less fuel than it should as the airflow reading is wrong and then try and it will then try and compensate for it, giving the symptoms you have. The ECU / AFM is very sensitive at low airflows.
Mark
Mark
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


