temperature guage
temperature guage
Author
Discussion

daz the plumber

Original Poster:

14,997 posts

262 months

Wednesday 22nd April 2009
quotequote all
my temperature guage as just stopped working , can any one tell me where the sensor is located on the serp engine and how do i go about testing it .don`t know if its a coincidence or a wire as been damaged due to the new front bottom wish bones being fitted . the needle is hard down to the left and there is no movement .

Chimjunkie

2,879 posts

242 months

Wednesday 22nd April 2009
quotequote all
Sensor is on front of engine hidden behind the distributor. If you pull the single connection off and ground it to the engine the guage needle should move right round to the right. If it does then the wiring and guage are ok. but the sensor is duff. If not then the wiring or guage could be suspect, but the sendor ok.

debaron

878 posts

228 months

Wednesday 22nd April 2009
quotequote all
yes

+1


Pretty straightforward job to change if the sensor is duff:


debaron said:
Dizzy out is the best way to get to the sender unit on the Serp. Mine is also reading low intermittently but the fans cut in now and again regardless of what's on the gauge so will change it.

Simple job - 45 mins.


PAS hose securing clip off (if fitted) - 10 mm ring spanner

14 mm Ring spanner to loosen Dizzy clamp

Twist dizzy when loose to get hand in and remove bolt and clamp

Pull dizzy off - stuff big rag in the hole! Don't want any junk (or water) getting into the engine!

The sender is then right there in front of you. I'd imagine water will come gushing out of the sender hole when removed so make sure you have a rag to stop it getting into the dizzy hole.

New one in and connect up. Dizzy back in and away you go. Obviously pay attention to exactly where the rotor arm is pointing and also mark the dizzy housing against the engine before removal so you can line up when refitting.
Hope this helps!

Ryan


daz the plumber

Original Poster:

14,997 posts

262 months

Wednesday 22nd April 2009
quotequote all
does that mean the timming as to be re set

Edited by daz the plumber on Wednesday 22 April 22:27

debaron

878 posts

228 months

Wednesday 22nd April 2009
quotequote all

Not if you pay attention to a few things.

Firstly, get a long flat head screwdriver and position it so half of the head is on the dizzy base and half on the engine casing directly below the dizzy base.

Next, give the screwdriver a little tap so it makes a mark in the engine casing and the dizzy base at the same time. Now you have a point that you can twist the dizzy base to in order to re-align the timing.

This ONLY works when the following is observed - The rotor arm needs to be pointing to the same place that it was before removal.

Take the cap off and photograph or mark where the arm points. When I did mine the arm was directly in line with one of the clips that hold the cap on. You can also mark the arm position on the black plastic cover under that says 'Do Not Remove'. I did this too for double checking.

Because of the relatively small number of teeth on the dizzy drive, it will either go back in noticeably before, after or exactly on your markings.

Worked fine for me. Twice.

daz the plumber

Original Poster:

14,997 posts

262 months

Thursday 23rd April 2009
quotequote all
just investigated this further to find a small blue resistor about 4" from the spade connector.it as broke away. is this standard or do you think it as been played with .help needed .ive put the cable to earth and the needle goes over to the right .

Chimjunkie

2,879 posts

242 months

Friday 24th April 2009
quotequote all
Sounds like someone has replaced the sensor with an incorrect one and tried to recalibrate. Unfortunately this is a common misconception and it does not work that way. You need the correct sensor. All the resistor will do is give a correct reading at say 80 deg, but all other temperatures will read wrong.

daz the plumber

Original Poster:

14,997 posts

262 months

Friday 24th April 2009
quotequote all
i replaced it for the correct one some time back .ive removed the resistor and its now working thanks .

daz the plumber

Original Poster:

14,997 posts

262 months

Saturday 25th April 2009
quotequote all
the temp sender as now gone erratic .i cleaned the terminals but no difference .can any one give me a part number for sender thanks