Found a chimaera I like
Discussion
Hi guys, I have found a chimaera after seeing about 8 of them. It is a little rusty on the chassis but nothing I think I have to worry about if it is treated now. The exhast is a little rusty too and i think it will eventually need replacing, i'll add a few photos. My main conundrum is do I get it inspected by someone like Rob Ingleby? looks like it will cost between 200 and 300 pounds but I suppose it will be money well spent. just a bit of a gulp if the car turns out to be a dog. Anyway let me know what you think!
Mark
Mark
Since I'm not identifying the car and the advert was actually in auto trader, I hope I'm not breaking any rules! I have got him down to £8750 but that is pretty much all my budget. It needs new rears but body is perfect and the hood is in good order, interior seems to have no issues but in the foot well near the battery there is a small section of carpet missing and there are two shiny pipes (not sure what they are for) and where they enter the central body/tunnel they are corroded. ufortunately I didn't get a picture (one of those Doh! moments!)
Markedman2020 said:
lewis_sharman said:
hmmm 
I might have to drill three holes like that . . . atm i need some boot drainage
Actually I've seen the holes on all of them I was more interested in the ball joint. Lol
I might have to drill three holes like that . . . atm i need some boot drainage


Thats the ARB droplink, the pair can be replaced for around £50 with uprated ones from Steve Heath, but tbh the ones that i have just taken off of my car looked worse than that and were still very sturdy.
My old exhaust was also in similar looking condition, but was just surface rust. Even if it is rusty, see it as an excuse to get the ACT cherrybombs

I think you may need to budget for outrigger replacement at some point. Allowing the dirt and gravel to build up in the corners of the outriggers like that traps moisture for longer that's why the tubes go in this location first.
Here's my chassis shame my car isn't a 450 as it is for sale.

Here's my chassis shame my car isn't a 450 as it is for sale.

Edited by Red Cabbage on Sunday 3rd May 18:44
Red Cabbage said:
I think you may need to budget for outrigger replacement at some point. Allowing the dirt and gravel to build up in the corners of the outriggers like that traps moisture for longer that's why the tubes go in this location first.
How much is that likely to set me back? I saw an article in Sprint that talked about chopping them off and welding on new ones, a company called TvR, but they didn't mention the price.Edited by Markedman2020 on Sunday 3rd May 18:45
Mine has all the same holes/vents as the one you're looking at, so no worries there. However, looking at the picture in your 18:04 post, I would be inclined to have a good dig with a screwdriver where that build-up of road dirt is sitting - you may just find it goes straight through. It looks like a set of Steve Heath drop links would also be on the shopping list. Also, if the chassis hasn't had much attention (as appears to be the case) what are the suspension units like? If they are the originals, you'll probably need to replace them quite soon too.
Red Cabbage said:
I think you may need to budget for outrigger replacement at some point. Allowing the dirt and gravel to build up in the corners of the outriggers like that traps moisture for longer that's why the tubes go in this location first.
Here's my chassis shame my car isn't a 450 as it is for sale.

I have actually got in contact with you but wanted to look at some lower milage versions a little closer to home before I came up. Thinking of putting around 9000miles a year on it and so a little concerned with resale value.Here's my chassis shame my car isn't a 450 as it is for sale.

Edited by Red Cabbage on Sunday 3rd May 18:44
Edited by Markedman2020 on Sunday 3rd May 18:48
Markedman2020 said:
Red Cabbage said:
I think you may need to budget for outrigger replacement at some point. Allowing the dirt and gravel to build up in the corners of the outriggers like that traps moisture for longer that's why the tubes go in this location first.
How much is that likely to set me back? I saw an article in Sprint that talked about chopping them off and welding on new ones, a company called TvR, but they didn't mention the price.Edited by Markedman2020 on Sunday 3rd May 18:45
Edited by Red Cabbage on Sunday 3rd May 19:04
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



