Idle Control - an idea for discussion
Idle Control - an idea for discussion
Author
Discussion

Barkychoc

Original Poster:

7,848 posts

235 months

Wednesday 6th May 2009
quotequote all
I've been rattling an idea around in my head for a while for a simple idle speed controller that could replace the stepper motor.

This is only an idea for discussion, I haven't really thought about the practicalities of installing it etc, but I thought I'd share it anyway even if you shoot me down in flames.

Basically my thought is to establish 2 idle air bleed circuits, one fixed for normal idling, and another which adds additional air via a solenoid valve for cold idling to prevent stalling when cold.
The valves would be adjusted to achieve this then I envisage they would not need to be touched again.
The solenoid valve I thought in its simplest form could just be activated by a dashboard switch - though if you so wished it could clearly get much more elaborate.

A fag packet sketch below.

I await your comments paperbag


450Nick

4,027 posts

243 months

Wednesday 6th May 2009
quotequote all
Thats basically how mine works already... Except the solenoid is an bypass 2 wire stepper motor controlled by the ecu so it can vary the addition air, slowly closing as the car warms up... Works very nicely smile

paulathome

686 posts

249 months

Wednesday 6th May 2009
quotequote all
I was looking at something similar a while ago but doing it electronically. Basically doing away with the stepper motor and using a PWM idle valve and fitting electronics between the stepper motor plug (which would simulate the stepper motor to the ECU) but would then drive a PWM valve which would react much quicker than the rather clockwork stepper.
Not thought yet about how to do it but you now have me thinking all over again.idea
Paul.

spend

12,581 posts

282 months

Wednesday 6th May 2009
quotequote all
If you look at the plenum you have pretty much described the standard system. If only half of them hadn't been buggered about with there'd only behalf the problems. I've even seen idle screws closed and throttle stops opened to defeat the bypass and allow air in past the butterfly!!!

miniman

30,239 posts

293 months

Wednesday 6th May 2009
quotequote all
It always baffled me how an engine as ubiquitous and well developed as the Rover V8 suffers from such a silly problem. It nearly drove me to getting rid of the Chim altogether until I just unplugged the damn stepper motor altogether and put up with 2-3 minutes of rough idle when cold. Do Range Rovers suffer from this problem?

350Matt

3,917 posts

310 months

Thursday 7th May 2009
quotequote all
Nowhere near as bad but yes they do have it.

The issue with TVR's is things get rather hot under there, plus they tend to be driven harder and worried over more than your average landy

blitzracing

6,422 posts

251 months

Thursday 7th May 2009
quotequote all
The problem is no so much the physical stepper, but the way its made to respond. Basicly its "burst" fired to slow the engine rpm, and then waits for a short period for the idle to settle. If its still wrong it applies another burst of pulses, and thats why the rpm steps the way it does. This is fine until either the stepper jams up,(it has no position sensor to tell where it is) or the engine does not slow in the expected manner. The latter is typical if the fueling or ignition is not spot and so the rate of RPM change does not match what the ECU is expecting. It then ends up over shooting, so the tickover is unstable. A well set up and maintained engine with a clean stepper motor should not have problems like this, and its shows an underlaying problem elsewhere. If you suffer an over high tick over you can put a "reduction bung" with a 6mm hole into the stepper feed tube to limit the air so it cant over rev so much, but can still provide some extra air when the engine is cold.

Mark

spend

12,581 posts

282 months

Thursday 7th May 2009
quotequote all
blitzracing said:
... but can still provide some extra air when the engine is cold....
and that is all it should ever be doing otherwise the problem is elsewhere IMHO?

blitzracing

6,422 posts

251 months

Thursday 7th May 2009
quotequote all
The problem is the stepper resets (as it has no feedback for its position) every time you turn off the ignition, so its always wide open on a start, more than is really needed in most conditions.