Fitting a Wideband Lambda Sensor.
Fitting a Wideband Lambda Sensor.
Author
Discussion

Pink_Floyd

Original Poster:

900 posts

252 months

Monday 11th May 2009
quotequote all
The existing Lambda sensors are mounted in a recess so that the sensor tip is in the middle of the exhaust flow. Should I try and mount a wideband sensor in the same way or will it make very little difference if the mount is on the side of the pipe??.

Meatball

1,638 posts

241 months

Monday 11th May 2009
quotequote all
I fitted mine below the main cat at about 10 past or 10 to on a clock.
Ive had no problems with the readings.
HTH

GreenV8S

31,027 posts

315 months

Monday 11th May 2009
quotequote all
I fitted mine with a standard boss welded on the outside of the pipe, and they seem to work fine. Just make sure it isn't at the bottom of the pipe, because condensation running down the pipe following a cold start can wreck the sensor.

Pink_Floyd

Original Poster:

900 posts

252 months

Tuesday 12th May 2009
quotequote all
Meatball said:
I fitted mine below the main cat at about 10 past or 10 to on a clock.
Ive had no problems with the readings.
HTH
Are you using yours to run a Gauge or for engine management?
I was worried that if the sensor is a long way from the engine then the time lag would upset a Megasquirt system.
Initially its to run a gauge but want to move over to megasquirt with wideband next year.

Meatball

1,638 posts

241 months

Tuesday 12th May 2009
quotequote all
Pink_Floyd said:
Meatball said:
I fitted mine below the main cat at about 10 past or 10 to on a clock.
Ive had no problems with the readings.
HTH
Are you using yours to run a Gauge or for engine management?
I was worried that if the sensor is a long way from the engine then the time lag would upset a Megasquirt system.
Initially its to run a gauge but want to move over to megasquirt with wideband next year.
Its currently running a gauge to monitor the fuelling with the option to hopefully fit megasquirt in the winter, Which wideband are you using?

chrispitman

742 posts

285 months

Tuesday 12th May 2009
quotequote all
I fitted mine in the existing place ground out the old boss and a local welder made a plate and welded back in, works fine. Need to get the other side done so if there is a problem the sensor can be switched over. They need to go before the CAT.

Pink_Floyd

Original Poster:

900 posts

252 months

Tuesday 12th May 2009
quotequote all
Meatball said:
Its currently running a gauge to monitor the fuelling with the option to hopefully fit megasquirt in the winter, Which wideband are you using?
The gauge will probably be the Innovate G2 with the Techedge 2J1 with the latest Bosh sensor from Trigger-Wheels.
Was going to use the Innovate LC1 but there seems to be mixed reviews on that one.

Meatball

1,638 posts

241 months

Tuesday 12th May 2009
quotequote all
Pink_Floyd said:
Meatball said:
Its currently running a gauge to monitor the fuelling with the option to hopefully fit megasquirt in the winter, Which wideband are you using?
The gauge will probably be the Innovate G2 with the Techedge 2J1 with the latest Bosh sensor from Trigger-Wheels.
Was going to use the Innovate LC1 but there seems to be mixed reviews on that one.
Im also using the G2 gauge (£40 on ebay) with the LC1 most of the issues with this come downthe grounding, ive had no problems with mine.
Have also spoke the innovate regarding fitment after cat and again theres no problem.

Pink_Floyd

Original Poster:

900 posts

252 months

Tuesday 12th May 2009
quotequote all
Meatball said:
Have also spoke the innovate regarding fitment after cat and again theres no problem.
chrispitman said:
I fitted mine in the existing place ground out the old boss. They need to go before the CAT.
I have just been reading http://wbo2.com/lsu/lsuinstal.pdf And it suggests that WideBand sensors should be 1mtr '40"' from an exhaust outlet otherwise they can get to hot and not work properly. NarrowBand sensors don't have this problem so can go right up to the exhaust port. The level of oxygen should be no different after the cat than before so I am not sure why
chrispitman said:
They need to go before the CAT.
Is it just the time it takes for changes to the fueling to be noticed?

Meatball

1,638 posts

241 months

Tuesday 12th May 2009
quotequote all
Unless you take the main cat out theres nowhere to place the WB sensor so it can read the gasses equally from each bank.

adyw

388 posts

274 months

Tuesday 12th May 2009
quotequote all
I wonder who told you that, wavey

Meatball

1,638 posts

241 months

Wednesday 13th May 2009
quotequote all
adyw said:
I wonder who told you that, wavey
Big head biglaugh
have you fixed your Megasquirt yet?

Pink_Floyd

Original Poster:

900 posts

252 months

Wednesday 13th May 2009
quotequote all
Meatball said:
Unless you take the main cat out theres nowhere to place the WB sensor so it can read the gasses equally from each bank.
I read something some time ago that said the sensor should be before the CAT but didn't explain why, anyone know.
I was going to fit 2 bungs and change the sensor from bank to bank every now and then, not the best. So putting after the CAT if it really does not matter would be better. Have you mounted yours on the pipe below the CAT or after the bend before it joins the rest of the exhaust system.

Meatball

1,638 posts

241 months

Wednesday 13th May 2009
quotequote all

Ant.

5,254 posts

312 months

Wednesday 13th May 2009
quotequote all
Meatball said:
Im also using the G2 gauge (£40 on ebay)
Can't find any for that price on Ebay, got a link to the seller please?

Edited by Ant. on Wednesday 13th May 18:49

adyw

388 posts

274 months

Wednesday 13th May 2009
quotequote all
yesyep all working fine driving complete with G2 guage now.