help b*@@*y ball joints
help b*@@*y ball joints
Author
Discussion

myquest

Original Poster:

78 posts

258 months

Wednesday 13th May 2009
quotequote all
Got new top and bottom ball joints, track rod ends and engine mounts. Did the engine mounts this pm, passenger side a swine driver's a doddle. Thought I'd just do the trackrod ends before finishing, couldn't break the lock nut on either side despite swamping in WD40, eventually got nearside to release and fitted new end allowing for slight differnce in length.

The offside one won't budge and I think I may have rounded it, any suggestions as to anything else I can do ? Or do I have to admit defeat and get the guys doing the geo to do it?

I'm also a bit puzzled as to how I can split the top ball joint from the hub carrier due to the end of the joint being recessed in the carrier.

Any suggestions gratefully received as I am hoping to get all this done by the weekend.

Thanks

steve-V8s

2,924 posts

279 months

hibutts

38 posts

218 months

Wednesday 13th May 2009
quotequote all
Whist you at machine mart this may help with the seized nut:

http://www.machinemart.co.uk/shop/product/details/...

SP6 Animal

6,015 posts

241 months

Wednesday 13th May 2009
quotequote all
Force that tool in with a lump hammer it will soon break the seal.

Pupp

13,044 posts

303 months

Wednesday 13th May 2009
quotequote all
When I did mine, I had a 'mare splitting the joint from the upright. It's the only job on any vehicle where I had to go out and buy a bigger hammer (and it still didn't come apart with big FO joint splitter) evil

In the end, it did came apart with just one very sharp tap from a ball pein hammer and no splitter wedge....on the side of the 'cone' part of the upright. Apparently, done right, this is enough to distort the internal taper so that the bond with the joint is broken.... Was a tip from an indie and worked a treat wink

philmccann

430 posts

231 months

Thursday 14th May 2009
quotequote all
Had mine off last week to fit a new gaiter to the steering rack. Had one similar to this in the garage, worked a treat!!!

HTH

Phil

http://www.shop-com.co.uk/Sealey_Ball_Joint_Puller...

Barkychoc

7,848 posts

235 months

Thursday 14th May 2009
quotequote all
For the track rod end if you can't get it to shift saw the balljoint and socket off the end (so the shaft of the balljoint is still there but you can get the tool below over the remaining bit) then use one of these to split the nut.

http://www.machinemart.co.uk/shop/product/details/...


Adrian@

4,667 posts

313 months

Thursday 14th May 2009
quotequote all
I'm also a bit puzzled as to how I can split the top ball joint from the hub carrier due to the end of the joint being recessed in the carrier.

You can remove the top ball joint adapter by dressing the weld off the lower part of the locating tag (as these are welded on after the adapter is fitted) undoing the locking bolt out of the ford casting, and then work with this off the car (if someone PMs me direct and wants to host a couple of pictures of the parts as new adrian@exactly.demon.co.uk
Adrian@

spend

12,581 posts

282 months

Thursday 14th May 2009
quotequote all
Barkychoc said:
For the track rod end if you can't get it to shift saw the balljoint and socket off the end (so the shaft of the balljoint is still there but you can get the tool below over the remaining bit) then use one of these to split the nut.

http://www.machinemart.co.uk/shop/product/details/...
Hmmm.. quick bit of heat and some agricultural stilsons would be a lot easier IMHO.

spend

12,581 posts

282 months

Thursday 14th May 2009
quotequote all
IIRC I removed the upper BJ's with something like this:


but had to pack a socket / nut to space the thread of the BJ out of the recess.

It was a while ago though....hehe

Adrian@

4,667 posts

313 months

Thursday 14th May 2009
quotequote all
Thanks Dave......These are the 2 parts that make up the top ball joint adaptor, the male part gets dropped into the Ford upright and the locking tang then get welded into place...to remove it, remove the clamp bolt, dress off the the lower weld on the tang and knock out of the upright (this allow stubborn ball joints to be drilled out from the inside)
Adrian@


The tang can be welded back on (if you have dressed that much off that it requires it) when it is off the car, as long as the new weld can pass down the slot on the upright.



Edited by Adrian@ on Thursday 14th May 15:27

myquest

Original Poster:

78 posts

258 months

Thursday 14th May 2009
quotequote all
Thanks for all the assistance guys, finally managed to undo the stubborn track rod and chaged that, then did the offside ball joints. Top came away third sharp hit with hammer and did doth in < 1 hour.

Nearside totally different took 2 1/2 hours as top would not split, then remembered my Vauxhall training and used 2 hammers, 1 held against cone opposite side to the one i hit it with and after 10 or so sharp taps it came appart!

Anyway all done now and booked in for a full geo set up next week, also took the opportunity to clean up the front corners of the chassis and outriggers. Will let dry overnight then put wheels back on and check out the difference in the suspension.

Thanks again for the help.

mike