Camber settings
Camber settings
Author
Discussion

sapper

Original Poster:

1,134 posts

236 months

Monday 18th May 2009
quotequote all
My rear tyres sometimes catch the rear arches when driving over some of our less than perfect road surfaces.
I have 17'' wheels all round and the rear tyre size is 225/45/17.

Ive just fitted new shocks and bushes and then I had the alighnment checked and corner weight adjusted.

Do i need to get the camber settings changed?

If so has anyone got any experience and reccomendations?



steve-V8s

2,924 posts

279 months

Monday 18th May 2009
quotequote all
What offset are the wheels ? Will probably be stamped on them ET and then some numbers.

mlow

21 posts

298 months

Monday 18th May 2009
quotequote all
I use 2 degrees negative on the rear but do a good number of track days where the extra camber is useful. Half a degree less would probably be sufficient for predominantly road use to avoid wearing the inner edge of the tyres.

sapper

Original Poster:

1,134 posts

236 months

Monday 18th May 2009
quotequote all
steve-V8s said:
What offset are the wheels ? Will probably be stamped on them ET and then some numbers.
Sorry for the delay.

Ive had a look and cant find the offset.

sapper

Original Poster:

1,134 posts

236 months

Monday 18th May 2009
quotequote all
mlow said:
I use 2 degrees negative on the rear but do a good number of track days where the extra camber is useful. Half a degree less would probably be sufficient for predominantly road use to avoid wearing the inner edge of the tyres.
If I was to go 1.5 negative on the rear would the front also be adjusted.


steve-V8s

2,924 posts

279 months

Monday 18th May 2009
quotequote all
I asked what the wheel offset was because plainly if you are running 17inch wheels they are not the originals. 225s at the rear are not that wide so I would think if all else is well the camber would have to be a long way off to cause rubbing on the wheel arch. The marking is usually stamped on the rim somewhere, often you will need to take the wheel off to see it. Not looked at the rolling diameter of 225/45/17 but assume you have checked it is similar to the original size. Have you used these wheels /tyres for some time without problems or are they new ?

Konrod

912 posts

259 months

Monday 18th May 2009
quotequote all
Stand to be corrected on this one, but here goes.........

I have the same problem although I am on the standard 225/50R16s. When I asked about it I was told (on here!) that the Avon ZZ3's I have are squarer in the "shoulders" which rubs the inside wheelarch "in extremis" - apparently ZZ3s were designed for Porsches??. I suppose the regularly mentioned tyres have more rounded shoulders which doesn't cause the problem (Falken, Toyo, Dunlop etc.). This may also be your problem if you are on non-standard rims and tyres.

Anyone want to confirm or shoot me down?

As my rears are getting worn (can't imagine how hehe) I might change them before Le-Mans as that is when I usually experience the problem (two up with a boot full of roof and beer!)

J

HRG

72,863 posts

270 months

Monday 18th May 2009
quotequote all
sapper said:
My rear tyres sometimes catch the rear arches when driving over some of our less than perfect road surfaces.
I have 17'' wheels all round and the rear tyre size is 225/45/17.

Ive just fitted new shocks and bushes and then I had the alighnment checked and corner weight adjusted.

Do i need to get the camber settings changed?

If so has anyone got any experience and reccomendations?
Yup, I run 1 degree front and rear camber with 265/35 18 on the back and mine foul too. I'm having my inner arches re-glassed this week smash You sure you're only running 225 on the rear?

Ab Shocks

1,686 posts

251 months

Monday 18th May 2009
quotequote all
mlow said:
I use 2 degrees negative on the rear but do a good number of track days where the extra camber is useful. Half a degree less would probably be sufficient for predominantly road use to avoid wearing the inner edge of the tyres.
I think that 1.5 degrees neg camber is more than enough but I tend to run more rear toe to aid traction.

myquest

78 posts

258 months

Monday 18th May 2009
quotequote all
According to the bible camber should be front and rear -0.5 to -1.0, (ideally -0.75) and toe in should be 20 minutes front and rear.

daz the plumber

14,997 posts

262 months

Monday 18th May 2009
quotequote all
i dont think the geo is the problem .you need a offset around 35 for the rears .i have 17" wheels on the back with 245 tyres and a 8 j rim with no problems .check your ride height . you need it to be anything from 150 mm from the the steel plate infront of the rear wheels .

Chimjunkie

2,879 posts

242 months

Monday 18th May 2009
quotequote all
Konrod said:
Stand to be corrected on this one, but here goes.........

I have the same problem although I am on the standard 225/50R16s. When I asked about it I was told (on here!) that the Avon ZZ3's I have are squarer in the "shoulders" which rubs the inside wheelarch "in extremis" - apparently ZZ3s were designed for Porsches??. I suppose the regularly mentioned tyres have more rounded shoulders which doesn't cause the problem (Falken, Toyo, Dunlop etc.).
Quite true. Tyre brands are very different with their profiles and actual widths.
Some of the tyres i've had on the rear:

225 bridgestone S03 had 9.25" width
245 Toyo T1R had 9" width
245 Toyo R888 have 10" width!!