4.0 or 4.0HC? How do I tell?
4.0 or 4.0HC? How do I tell?
Author
Discussion

BRITISHBEEF

Original Poster:

75 posts

217 months

Tuesday 19th May 2009
quotequote all
This has probably been asked before but I can't seem to find it on search. I bought my Chim about 7mths ago as a standard 4.0, but was bored the other day and had seen the 'we buy any car' crappy advert so got curious. Put in my reg number and it brought it up as a 4.0HC? Is there a quick way of finding out?
They wouldn't give me a figure by the way!!!

Cheers.

daz the plumber

14,997 posts

262 months

Tuesday 19th May 2009
quotequote all
i would not bother about that , there`s not alot of difference between the two .just a slightly higher lift cam ,double valve springs and concave pistons .the cam may of been changed so who knows what it is .ive drove both and i would say the standard 4l drives better at low revs , less shunting .

Simon Says

19,466 posts

252 months

Tuesday 19th May 2009
quotequote all
There is a noticeable difference if you drive both back to back if both have healthy engines,the low speed torque is better on the 4.0 non-HC,cant say the HC would be worth any more money to be honest wink notched pistons,double valve springs and Vernier timing gear,the ECU normally as 40HC on the label written in marker pen and so does the chip inside the case,but its a TVR so anything is liable to be different.

Edited by Simon Says on Tuesday 19th May 11:34

Clippy

196 posts

214 months

Tuesday 19th May 2009
quotequote all
I have a 400HC and all of the above is about right: -
400HC on the plenum (but anyone could add that)
40HC on the ECU and chip
double valve springs
duplex vernier timings gear
pistons etc.

Possibly feels more sluggish around the 2,000 - 3,000 rpm mark than a 'standard' 400 (if you put your foot down at 2k that is - still shoots from a standing start really well) then flys between 3,500 and 5,500. Pulls like a train and that difference was really noticable when I was test driving pretty much back-to-back.

It does shunt a little around town too, but a sensitive right foot can pretty much hide this tendency.

No idea if there's really any difference price wise in the marketplace - I would suggest that condition is still more important than spec, so probably nothing worth writing home about unless you find an absolutley mint HC...

Giles

Simon Says

19,466 posts

252 months

Tuesday 19th May 2009
quotequote all
Clippy said:
I have a 400HC and all of the above is about right: -
400HC on the plenum (but anyone could add that)
40HC on the ECU and chip
double valve springs
duplex vernier timings gear
pistons etc.

Possibly feels more sluggish around the 2,000 - 3,000 rpm mark than a 'standard' 400 (if you put your foot down at 2k that is - still shoots from a standing start really well) then flys between 3,500 and 5,500. Pulls like a train and that difference was really noticable when I was test driving pretty much back-to-back.

It does shunt a little around town too, but a sensitive right foot can pretty much hide this tendency.

No idea if there's really any difference price wise in the marketplace - I would suggest that condition is still more important than spec, so probably nothing worth writing home about unless you find an absolutley mint HC...

Giles
Spot on thumbup

daz the plumber

14,997 posts

262 months

Tuesday 19th May 2009
quotequote all
one good thing is you have more of a choice when it comes to future cam selection due to the pistons , you are very limited with the standard 4l

Simon Says

19,466 posts

252 months

Tuesday 19th May 2009
quotequote all
daz the plumber said:
one good thing is you have more of a choice when it comes to future cam selection due to the pistons , you are very limited with the standard 4l
Depends how wild you want to go,the 285 Piper works well in this motor with no mods so i am lead to believe,as for my choice of cam H404 that would not suit a lot of peoples driving habits(bit spiky/peaky in the 4.0)if i lived in town i think something like the MC1 or Stealth would be more suitable,a piston/valve clearance check is always worthwhile in case the blocks been decked or the heads skimmed all IMHO

BRITISHBEEF

Original Poster:

75 posts

217 months

Tuesday 19th May 2009
quotequote all
I can't find anythihg that says HC, but it deff has the shunt at slow speeds! I think I'll just assume it is the normal 4.0 and not worry about it.

Thanks guys.

Rum Runner

2,349 posts

248 months

Wednesday 20th May 2009
quotequote all
Best thing to do is pull the ECU ouit from under the carpet and you will probably find it painted on the ECU or marker pen 4.0HC.
Oh and if it rev's very un V8 like at the top end it def a HC.

scotty_d

6,795 posts

225 months

Thursday 21st May 2009
quotequote all
My standard 400 has Recently been on the rolling road and running very well I believe the cam has been changed to a spiky one not too long ago as it shunts a lot below 2k but pulls very strong after.

Simon Says

19,466 posts

252 months

Thursday 21st May 2009
quotequote all
Shunting is no indication of cam spec,well not on the RV8 anyway frown plenty of stock 4.0,s shunt like a bd irked

scotty_d

6,795 posts

225 months

Thursday 21st May 2009
quotequote all
Simon Says said:
Shunting is no indication of cam spec,well not on the RV8 anyway frown plenty of stock 4.0,s shunt like a bd irked
Oh well good to no its not just mine then.

Simon Says

19,466 posts

252 months

Thursday 21st May 2009
quotequote all
scotty_d said:
Simon Says said:
Shunting is no indication of cam spec,well not on the RV8 anyway frown plenty of stock 4.0,s shunt like a bd irked
Oh well good to no its not just mine then.
I think you will find...salesman quote...ah yes,they all do that sir laugh