Clutch release bearing
Clutch release bearing
Author
Discussion

drew.h

Original Poster:

526 posts

220 months

Wednesday 20th May 2009
quotequote all
Amusing this is what is causing the awful noise on my clutch when depressed, which one do I need?

I can find two part numbers Q0107 and Q0014. Its is an early Chimaera, but I think someone has fitted the T5 gearbox in the past, because reverse is to the right and back.

S4CJO

429 posts

290 months

Wednesday 20th May 2009
quotequote all
What year is the car, and yes the T5 gate is to the right. The box is a retro fit the to Landie variant.


HRG

72,863 posts

270 months

Wednesday 20th May 2009
quotequote all
Can you do the release bearing without dropping the box?

drew.h

Original Poster:

526 posts

220 months

Wednesday 20th May 2009
quotequote all
Its a '93, so originaly I think it should have had the Rover box.

Any advice on replacing welcome.

spend

12,581 posts

282 months

Wednesday 20th May 2009
quotequote all
drew.h said:
Its is an early Chimaera, but I think someone has fitted the T5 gearbox in the past, because reverse is to the right and back.
I'd check carefully which box is in it, whilst box swaps are not common IIRC there may have been as few (I can't really say 'many' can I now hehe ) LT77-R380 conversions as LT77-T55 conversions, and the R380 also has reverse to the right??? Some 'early' cars did seem to get T5's in advance of others, as usual TVR just loved to keep us guessing wink

IIRC quick way to tell is look at the propshaft, T5 is push on and LT77/R380 are both bolt up flanges

lewis_sharman

5,958 posts

222 months

Wednesday 20th May 2009
quotequote all
The release bearing on mine is also making a horrid noise, but the clutch is fine and i don't really want to be spending £100's at a garage on something that is just making a noise and not affecting drive at all.

Is it a DIY job? Ive not messed around with gearboxes and clutches before.

HRG

72,863 posts

270 months

Wednesday 20th May 2009
quotequote all
I haven't seen inside or a diagram. It'd be nice if you could remove the actuator arm from below or via the slave cylinder but I doubt we're that lucky smash

Does anyone know for sure?

nemasis

310 posts

283 months

Wednesday 20th May 2009
quotequote all
unfortunately its box and bellhousing off to do the release bearing

HRG

72,863 posts

270 months

Wednesday 20th May 2009
quotequote all
thumbup Good job mine only squeals first thing in the morning reversing out of the garage then biggrin

I'll add it to the list of jobs to do if I ever split the engine and box.

Barkychoc

7,848 posts

235 months

Wednesday 20th May 2009
quotequote all
nemasis said:
unfortunately its box and bellhousing off to do the release bearing
...and as a result it wouldn't be wise to replace just the bearing, with the labour involved to get it all apart it makes sense to have a full clutch.

drew.h

Original Poster:

526 posts

220 months

Wednesday 20th May 2009
quotequote all
She had a clutch shortly before I bought her. A bill for one came with the car anyway.

I still don't know which one is correct for what I assume is the T5 box.

Barkychoc

7,848 posts

235 months

Wednesday 20th May 2009
quotequote all
drew.h said:
She had a clutch shortly before I bought her. A bill for one came with the car anyway.

I still don't know which one is correct for what I assume is the T5 box.
Maybe the lazy buggers didn't change the bearing?

drew.h

Original Poster:

526 posts

220 months

Thursday 21st May 2009
quotequote all
I assumed they had put the wrong one in.
No one appears to knows which is the correct one