induction cooling....
induction cooling....
Author
Discussion

darkcat

Original Poster:

2,354 posts

201 months

Thursday 25th March 2010
quotequote all
When i was under the bonet yesturday after attaching my custom stepper bypass mod (more on that later) in a lay-by with the engine running, For some reason i noted the temperature of the induction hose & flow sensor block, they where quite, to very warm.
I can only assume due to radiant head from the manifold, and other general hot air sources.

This of course means that, due to the length of the hose, the air will be at pretty much that same temperature when it hits the plenum, which was quite warm itself. OK in mid winter this may not be too much of a bad thing, helps top stop frosting on the injectors etc, but in mid summer, i can see induction of 60c+

Has anyone fitted any sort of heat shield or similar to help this?

scotty_d

6,795 posts

225 months

Thursday 25th March 2010
quotequote all
Hi
There are quite a few different solutions to reducing the induction temperature due to the manifolds being so close. ACT kit smooth bore with a heat reflective sleeve round the intake is what i have and you could knock up a heat reflective bracket too which i have been looking in too as well.

Sure someone will come up with more.

Scotty

spend

12,581 posts

282 months

Thursday 25th March 2010
quotequote all
It cools pretty well if you are moving and the engine is pumping tons of air through (very quickly). You can improve it, but main benefits are power for traffic light GPs in traffic & rolling roads hehe

Tweaking for little gains is long slippery downhill slope once you start wink

daveparry

988 posts

231 months

Thursday 25th March 2010
quotequote all
I have mused the idea of cutting a hole in the inner wing and routing the induction hose outside of the engine bay all together!

daveparry

988 posts

231 months

Thursday 25th March 2010
quotequote all
If you want shorter trumpets I have a set for sale lol!

K4TRV

1,819 posts

283 months

Thursday 25th March 2010
quotequote all
If your AFM's too hot check this with SC-Power:

http://www.sc-power.co.uk/pages/SC-Power-engine-mo...

HTH

Trev

lewis s

5,958 posts

222 months

Thursday 25th March 2010
quotequote all

cinquecento

558 posts

256 months

Friday 26th March 2010
quotequote all
my 2ps worth


daveparry

988 posts

231 months

Friday 26th March 2010
quotequote all
Your bonnet stay is on the wrong side!

daveparry

988 posts

231 months

Friday 26th March 2010
quotequote all
Did either of you two guys measure the temp before and after?

Del 203

12,728 posts

280 months

Friday 26th March 2010
quotequote all
daveparry said:
Your bonnet stay is on the wrong side!
The correct side on the better car wink

daveparry

988 posts

231 months

Friday 26th March 2010
quotequote all
Dead right Del it is the other side on the better car lol!

domV8

1,409 posts

212 months

Friday 26th March 2010
quotequote all
Del 203 said:
daveparry said:
Your bonnet stay is on the wrong side!
The correct side on the better car wink
You misspelt it, it's spelt "butters"...

hehe

.Mark

11,104 posts

307 months

Friday 26th March 2010
quotequote all
daveparry said:
Your bonnet stay is on the wrong side!
The correct side for a Griff, would take the aging drivers so long to get out and open the bonnet, with the stay on the passenger side the young gold digger can get out and do it wink

cinquecento

558 posts

256 months

Friday 26th March 2010
quotequote all
There was considerably less pressure drop at high map/rpm with the new induction piping which is a 3.5" silicon tube (the small orange piece top LH in pic) which is wrapped in 4/5 layers of fibreglass cloth, then enclosed in a black 4" tube for looks. I have dumped the original air filter in favour for a large one with a 3.5" opening.

There is little difference when driving regarding the air temp, air just doesn't stay that long in the induction pipe to get hot, however heat soak on a hot day is down, as is the time taken for the air temp to come down to around ambient when the engine is re-started.


kenny.R400

1,212 posts

271 months

Saturday 27th March 2010
quotequote all
All cooling mods attached with 3M duel Lock velcrosmile




spend

12,581 posts

282 months

Saturday 27th March 2010
quotequote all
Are you taking the peas?

That's certainly in the NOS style of mods evilhehe

chimaera1855

334 posts

199 months

Monday 16th August 2010
quotequote all
ahaha nice mods!!!where can i order this cooling kit???

markreilly

795 posts

203 months

Monday 16th August 2010
quotequote all
darkcat said:
When i was under the bonet yesturday after attaching my custom stepper bypass mod (more on that later) in a lay-by with the engine running,

Has anyone fitted any sort of heat shield or similar to help this?
Waiting with interest on what you have to say ?

slideways

4,101 posts

252 months

Monday 16th August 2010
quotequote all
chimaera1855 said:
ahaha nice mods!!!where can i order this cooling kit???
Iceland