Running on 7cyls with added hammering noises...
Discussion
Drove my 46k mile Chim 400 to work this morning. Midway through the journey I realised it started running on only 7 cyls; exhaust note 'offbeat' and out-of-balance vibration when parked at idle. At high engine loads there's also a metallic knocking/hammering that sounds like big-end bearing failure but a bit lighter and more 'tappety' (yet still bloody loud). This rattle is engine load/throttle dependant and is not related to revs. I could take the car to high revs but light load and it felt and sounded fine, but give it more gas and the knocking starts and stops with throttle presses. Oil press & temp is fine, I haven't lost any fluids.
I initially thought it might be a localised exhaust gasket/manifold failure, giving a raspy rattle at high gas flow pressure/speed, but why running on only 7? Spark plug semi-backed out giving a loss of compression, and noise when gas leaking past the gap? Rocker failure? Why if it is a valve-gear failure would the noise only come at high throttle/engine load settings as opposed to just high rpms?
Any advice would be gratefully received!
I initially thought it might be a localised exhaust gasket/manifold failure, giving a raspy rattle at high gas flow pressure/speed, but why running on only 7? Spark plug semi-backed out giving a loss of compression, and noise when gas leaking past the gap? Rocker failure? Why if it is a valve-gear failure would the noise only come at high throttle/engine load settings as opposed to just high rpms?
Any advice would be gratefully received!
Thanks for all the replies, chaps.
Peter, I don't think it's pinking I hear, it's more a loud, hard-edged mechanical clatter that sounds ominously like it may be a conrod bearing, yet seems to be slightly louder from the driver's side bank. Any pinking I've heard before was more a ticking or tinkling. It actually sounds similar to the problem you're encountering on your own Chim at the moment.
I may be able to blag an IR spot-temp doofer at work to check for a non-firing cyl without going on a plug-lead pulling frenzy. I'll try and isolate an ignition fault first then take things from there.
Peter, I don't think it's pinking I hear, it's more a loud, hard-edged mechanical clatter that sounds ominously like it may be a conrod bearing, yet seems to be slightly louder from the driver's side bank. Any pinking I've heard before was more a ticking or tinkling. It actually sounds similar to the problem you're encountering on your own Chim at the moment.
I may be able to blag an IR spot-temp doofer at work to check for a non-firing cyl without going on a plug-lead pulling frenzy. I'll try and isolate an ignition fault first then take things from there.
Could be any number of things but what you describe sounds very much like what happened to me about 7 years ago, it did not smoke just rattled/knocked loud under load, did not seem to loose much power either and to be honest i could not say it made it run lumpy and stopped it firing just made the noise you describe, was sorted by David Batty who noticed wear on bottom shells as well, has been fantastic ever since!! (but was a cracked piston). But could be caused by any of the other posts as well, dont think i would want to drive it until i knew for sure though !!!
Edited by only me on Wednesday 14th April 19:35
haircutmike said:
Rattly under load is pre-ignition, (pinking).
Get your ignition timing checked as it will only cause damage!
Pull of the plug extenders one at a time with an insulated pair of pliers to isolate The non igniter!
HCM.
Pinking, I bet he wishes !Get your ignition timing checked as it will only cause damage!
Pull of the plug extenders one at a time with an insulated pair of pliers to isolate The non igniter!
HCM.
Edited by roysum on Wednesday 14th April 21:11
My money would be on a duff HT lead or a plug extender.
Don't be a poof, start the car and wiggle each lead in turn. If its a duff lead it'll soon find you.
If you don't have curly hair after checking the leads, pull them off in turn and see if the car runs noticibly worse when the lead is removed you've found the extender or plug thats knacked.
It all warms up quickly, so don't piss around, and take the opportunity when you get zapped to practice your dad-dancing. Its loads of fun
Don't be a poof, start the car and wiggle each lead in turn. If its a duff lead it'll soon find you.
If you don't have curly hair after checking the leads, pull them off in turn and see if the car runs noticibly worse when the lead is removed you've found the extender or plug thats knacked.
It all warms up quickly, so don't piss around, and take the opportunity when you get zapped to practice your dad-dancing. Its loads of fun

The first thing i would do is remove the spark plugs looking for damage or a different colour.
If you start it from cold and let run for 10 - 15 seconds, you should be able to tell which exhaust manifold is NOT getting hot (indicating the faulty cylinder, assuming 1 is not firing) with out too much risk of burning the skin off your hands.
Camshaft wear ??
mine almost completely wore away one lobe so that the exhaust valve hardly opened.
Under light load the small valve opening was just enough to run ok'ish.
But under heavy load it soon started complain.
When i tried to drive it under load, it sounded like it was pinking except 50 time worse with a metallic sound to it.
It went from
"not running very well" and bad pinking!! under load at 5k rpm.
to
"barely runs at all" and bad pinking!! under load at less than 2k rpm.
in just a couple of weeks of daily use.
Or possibly, you have a rocker arm that has lost the steel pad that pushed the valve down, which sound like hammering noise you mentioned and if the steel pad found it's way past a valve it would of pinged around the cylinder until it hits the spark plug.
i hope it's not either of these, but i think they are worth considering.
good luck
Steve
edited so it makes sense, hopefully !!
If you start it from cold and let run for 10 - 15 seconds, you should be able to tell which exhaust manifold is NOT getting hot (indicating the faulty cylinder, assuming 1 is not firing) with out too much risk of burning the skin off your hands.
Camshaft wear ??
mine almost completely wore away one lobe so that the exhaust valve hardly opened.
Under light load the small valve opening was just enough to run ok'ish.
But under heavy load it soon started complain.
When i tried to drive it under load, it sounded like it was pinking except 50 time worse with a metallic sound to it.
It went from
"not running very well" and bad pinking!! under load at 5k rpm.
to
"barely runs at all" and bad pinking!! under load at less than 2k rpm.
in just a couple of weeks of daily use.
Or possibly, you have a rocker arm that has lost the steel pad that pushed the valve down, which sound like hammering noise you mentioned and if the steel pad found it's way past a valve it would of pinged around the cylinder until it hits the spark plug.
i hope it's not either of these, but i think they are worth considering.
good luck
Steve
edited so it makes sense, hopefully !!
Edited by Bensonv8 on Wednesday 14th April 22:56
Bensonv8 said:
The first thing i would do is remove the spark plugs looking for damage or a different colour.
If you start it from cold and let run for 10 - 15 seconds, you should be able to tell which exhaust manifold is NOT getting hot (indicating the faulty cylinder, assuming 1 is not firing) with out too much risk of burning the skin off your hands.
Camshaft wear ??
mine almost completely wore away one lobe so that the exhaust valve hardly opened, effectively running on 7. and when i tried to drive it, it sounded like it was pinking except 50 time worse. it went from "not running very well" to "barely runs at all" in just a couple of weeks of daily use.
Or possibly, you have a rocker arm that has lost the steel pad that pushed the valve down, which sound like hammering noise you mentioned and if the steel pad found it's way past a valve it would of pinged around the cylinder until it hits the spark plug.
i hope it's not either of these, but i think they are worth considering.
good luck
Steve
Good post!If you start it from cold and let run for 10 - 15 seconds, you should be able to tell which exhaust manifold is NOT getting hot (indicating the faulty cylinder, assuming 1 is not firing) with out too much risk of burning the skin off your hands.
Camshaft wear ??
mine almost completely wore away one lobe so that the exhaust valve hardly opened, effectively running on 7. and when i tried to drive it, it sounded like it was pinking except 50 time worse. it went from "not running very well" to "barely runs at all" in just a couple of weeks of daily use.
Or possibly, you have a rocker arm that has lost the steel pad that pushed the valve down, which sound like hammering noise you mentioned and if the steel pad found it's way past a valve it would of pinged around the cylinder until it hits the spark plug.
i hope it's not either of these, but i think they are worth considering.
good luck
Steve
haircutmike said:
Bensonv8 said:
The first thing i would do is remove the spark plugs looking for damage or a different colour.
If you start it from cold and let run for 10 - 15 seconds, you should be able to tell which exhaust manifold is NOT getting hot (indicating the faulty cylinder, assuming 1 is not firing) with out too much risk of burning the skin off your hands.
Camshaft wear ??
mine almost completely wore away one lobe so that the exhaust valve hardly opened, effectively running on 7. and when i tried to drive it, it sounded like it was pinking except 50 time worse. it went from "not running very well" to "barely runs at all" in just a couple of weeks of daily use.
Or possibly, you have a rocker arm that has lost the steel pad that pushed the valve down, which sound like hammering noise you mentioned and if the steel pad found it's way past a valve it would of pinged around the cylinder until it hits the spark plug.
i hope it's not either of these, but i think they are worth considering.
good luck
Steve
Good post!If you start it from cold and let run for 10 - 15 seconds, you should be able to tell which exhaust manifold is NOT getting hot (indicating the faulty cylinder, assuming 1 is not firing) with out too much risk of burning the skin off your hands.
Camshaft wear ??
mine almost completely wore away one lobe so that the exhaust valve hardly opened, effectively running on 7. and when i tried to drive it, it sounded like it was pinking except 50 time worse. it went from "not running very well" to "barely runs at all" in just a couple of weeks of daily use.
Or possibly, you have a rocker arm that has lost the steel pad that pushed the valve down, which sound like hammering noise you mentioned and if the steel pad found it's way past a valve it would of pinged around the cylinder until it hits the spark plug.
i hope it's not either of these, but i think they are worth considering.
good luck
Steve

(Great Chim in your profile
Thanks guys. I don't think it's camshaft wear as the car idled smoothly and revved very freely all the way until 6250 rpm until Monday morning! It also seems to go pull pretty well for a 400.
I think I'll give pulling HT leads off when it's running a miss. Call me a big girl's blouse, but I don't fancy doing the funny wiggly dance
The plan is to see if it's missing due to an electrical ignition fault first of all, then I'll take the rocker covers off and look for a missing pad/damaged rocker arm/broken rocker shaft spring. Incidentally, the rocker cover bolts seem to be multi-faceted star-headed bolts that look like male torx. Are those standard does anyone know? Buggered if I know what I'll use to get them off...
Edit: Just had a look at BensonV8's other post regarding spline-headed rocker cover bolts. Looks like that's what I have.
I think I'll give pulling HT leads off when it's running a miss. Call me a big girl's blouse, but I don't fancy doing the funny wiggly dance

The plan is to see if it's missing due to an electrical ignition fault first of all, then I'll take the rocker covers off and look for a missing pad/damaged rocker arm/broken rocker shaft spring. Incidentally, the rocker cover bolts seem to be multi-faceted star-headed bolts that look like male torx. Are those standard does anyone know? Buggered if I know what I'll use to get them off...
Edit: Just had a look at BensonV8's other post regarding spline-headed rocker cover bolts. Looks like that's what I have.
Edited by speedtwelve on Wednesday 14th April 23:46
Gassing Station | Chimaera | Top of Page | What's New | My Stuff





